TheHapaOne's CBS BRZ Limited
 

Current Mod List:
Interior
-JPM Coachworks Dash/Gauge Hood/Knee Pads/Speaker Panels
-JDM Black Interior pieces http://www.ft86club.com/forums/showp...3&postcount=46
-Anarchy Motive California Gold Shift Knob
-Diode Dynamics RGB footwell lighting
-Yospeed Heated Seat Switch Surround
-Perrin Drift Button/Reverse Lockout
-Full interior LED conversion

Exterior/Engine Bay
-Miro 398 18x8.5 +35 Matte Black
-Driveway Labs Version 1 Diffuser Prototype
-Rally Armor Mudflaps
-Perrin Short Antenna
-Perrin Brake Reservoir Coozy
-Tinted Windows
-Yellow Tinted Headlights and Foglights
-Cut and Blacked out Taillights
-Diode Dynamics LED Front/Rear Blinkers and Boomerang Always On Module
-LED Sidemarkers
-Password:JDM Gold Engine Dress-up
-Password:JDM Gold Battery Tie Down
-Debadged Trunk

Performance
-Perrin 2.75" CAI Powder coated Gold
-Perrin Black Inlet Hose
-Perrin 3" Resonated Catback
-Perrin Master Cylinder Brace
-Perrin Oil Cooler
-Nameless Catted FP/OP Prototype
-Tomei UEL Header
-HKS Hipermax SP Coilovers
-Password:JDM Gold Strut Bar/Diagonal Braces
-ATE Type 200 Dot 4 Brake Fluid
-DBA T2t Front/Rear Rotors
-Project Mu HC-800 Front Pads
-Hawk HPS Rear Pads



Dated Change Log:
7/18/2013 - Swapped side markers with smoked ones
7/19/2013 - Windows Tinted 25% all around
7/27/2013 - Perrin Front License Plate Relocation & Shorty Antenna
CF Vinyl covering on drill holes & Subaru letters debadged
8/5/2013 - Perrin Inlet Tube, Master Cylinder Brace, Drop in Filter
8/6/2013 - Apexi RS Extreme Catback Exhaust
http://i.imgur.com/vzdMzAM.jpg
That 4.8" really fills out the diffuser
8/12/2013 - Installed Perrin Oil Cap/Filter Cover and Master Cylinder Fluid Coozy
Installed OEM Black Shifter boot Bezel and Sport/TSC Buttons
8/13/2013 - Installed JPM Coachworks dash panels & had Eibach springs installed at Derrin's
9/16/2013 - Password:JDM strut kit and dress up kit installed
9/18/2013 - TOM'S USDM taillights installed - swapped to clear lens with @BRZPDX
11/3/2013 - installed nameless catted front/over pipe
11/23/2013 - tinted Headlights & Foglights Yellow Guys at Tommy's Tint did a good job
12/2/2013 - forgestars came in forgot to get Lug Nuts to fit them though :/ size is 18x9 +36 all around
2/22/2014 - after a while of no real mods decided to finish my interior black out
3/26/2014 - Perrin Cold Air intake and Oil Cooler installed
4/4/2014 - Springtime review http://www.ft86club.com/forums/showp...9&postcount=60
4/5/2014 - Drift Office tune
http://i.imgur.com/Ah6SPJP.jpg
Some time in April - Installed DBA rotors and Hawk Pads
11/9/2015 - Installed HKS Hipermax SP Coilovers
2/8/2015- Swapped Perrin 2.5" Catback to Perrin 3" Catback

4/17/2015 - Tomei UEL installed and FT86SF Catted Header Removed...Tuned In Eugene by VitTuned
http://i.imgur.com/4uqniPK.jpg
http://i.imgur.com/3XI1zlZ.jpg
http://i.imgur.com/5LP2Y2J.png
[ame="https://www.youtube.com/watch?v=FSvhSUpCThs"]2013 BRZ Dyno pull/Exhaust Video - YouTube[/ame]
Video Clip for your viewing pleasure

7/21/15 - Forgestars removed Miros installed
7/22/15 - Stickers removed
COMING SOON: Turbo?

Awesome i also have a black brz

Never seen one with a gas cover, and how do you like the diffuser?

Looking good

Diffuser is nice...but not sure it actually does anything just looks good

I honestly hate the gas cover just not willing to pull it off I am planning on getting the JDM trunk applique that matches it if I can find it

I highly recommend installing the clear side markers, they are a must (especially on black)

Have smoked ones they look much better than clear IMO

Good point they probably would look better!

I'll take some pictures of it this weekend and post them up

With the OEM diffuser, will the Perrin tips fit? I haven't seen the diffuser in person, not sure if it would be worth while to install the diffuser if I am planning on installing a Perrin exhaust further down the road. :iono:

I certainly like the look of the OEM diffuser and would definitely install it if it will work with my future mods.

I'll let you know after I install my exhaust which is 123mm

more parts added to the purchased list will be putting all the perrin stuff on today and will take pictures

Installed all the perrin stuff was going to take pictures but my toolbox decided to dump its contents all over the parking lot and I had somewhere to be will be taking pictures tomorrow and posting them up. Car has a noticeably different sound with the drop in filter and inlet tube as well as being quieter in the cabin since the resonator was deleted. Like it so far still making sure I installed it all correctly had some weird sounds but probably just due to increased air flow

Welcome from a fellow Hapa!

added new pictures of exhaust taking pics of engine bay and side markers right now will be posted soon

The Apexi exhaust really filled out the diffuser and gave the car a nice deep voice. Install took about 1 1/2 hours done on some ramps in my carport. I may have to get a torque wrench and torque the front bolts but the fitment seemed good and didn't feel overtighted and I tried to make both bolts even we will see.

Picked up some perrin stuff and put it on will take pics today after I lower and install my JPM Coachworks dash panels

Ordered some Forgestar f14s 18 x 9 +38 today from Modbargains should be here in 6-10 weeks

Just got my car back from the dealership (they were finally repairing a chip that was on it when I bought it) will be taking pictures of the stance after lowering it today.

Also ordered a CS style lip kit today hopefully it comes soon

Just got my car back from the dealership (they were finally repairing a chip that was on it when I bought it) will be taking pictures of the stance after lowering it today.

Also ordered a CS style lip kit today hopefully it comes soon

Ordered some more stuff today also decided to go with red TOM's hopefully I can get those soon along with the Password JDM stuff

Build is looking great, keep the pics comin! :clap:

Installed some more stuff this week...toms taillights and password JDM engine bay dress up kit and strut set

Installed a nameless catted front pipe today no pictures unfortunately

Had my headlights tinted yellow today will post pics this weekend

updated op with some new pics hopefully I can get the Forgestars on this weekend ordered some Muteki lugs that should be here tomorrow

Any plans for bbk? If not, painting the stock calipers would dress up those forgestars nicely. The car is coming along nicely btw!

Sent from my SCH-I535 using Tapatalk

haven't fully decided if I want to go bbk or not will probably paint my calipers red when it's not so cold around here

That will look pretty awesome in my opinion, can't wait to see more pics! :clap:

Well guess I got the wrong lug nuts now I had to pay an additional 50 for the ones from les schwab Damn should a just came in yesterday

sneak peak at the new wheels and tires will be taking full car photos tomorrow with the new set up

http://i.imgur.com/AgBI56A.jpg

Posted up a pic of my wheels installed wrapped with Federal tires (cheap and effective) Had a great experience dealing with @ModBargains.com to get these forgestars ordered Jurrian was super helpful and answered all my questions throughout the process. Definitely recommend them for putting in expensive orders. Now I just need some nice lugs to go with my wheels...anyone got a hookup on neo chrome or black lugs?

http://i.imgur.com/ClJli5B.jpg

installed this today...will need to get some padding to prevent too much unwanted banging but the drive home it didn't make any noise so may be ok

What are the specs of the wheels?

18x9 +36 all around

Great progress on this thing

ended up caving in an buying a header last night...can't wait to get some torque dip eliminating UEL goodness in a few weeks

Next Up: Brakes any suggestions? Going to do Fluid and Pads for sure want something not too squeaky but good enough for track/daily drive

http://i.imgur.com/621raMD.jpg
Finally got around to cleaning my baby...looks beautiful from this angle

so after washing my car I drove around for a good hour and found a couple spots to take some pictures

http://i.imgur.com/7PNDk5V.jpg
http://i.imgur.com/QuSa66R.jpg
http://i.imgur.com/b8sPA2t.jpg
http://i.imgur.com/qSHAocT.jpg
http://i.imgur.com/2AO9eVh.jpg
http://i.imgur.com/zUlHA7Y.jpg
http://i.imgur.com/RcFpKJ7.jpg
http://i.imgur.com/e9PTVsD.jpg

Car is looking good Brandon @thehapaone.

You've been busy.

Thanks man...and yup spending all my dough on the car

Glad to know you are still kicking been a while since you have been around here

Where did you get the shifter boot bezel and TC/VSC buttons? That looks really nice.