![]() |
Quote:
|
Quote:
Have you driven one yet? |
Quote:
|
Quote:
1. Power Power difference you can get out of V engine and boxer engine is ridiculous. For an example I'll use new Legacy 3.6R, which has 3.6L H6 engine. That engine name is EZ36D 3629CC DOHC, 260ps (256 hp) @6000rpm, 335Nm (247lbf-ft) @4400rpm. Top of my head, Toyota v6 engine that comes to mind is v6 engine from GS350, iirc it was 2GR-FE (correct me if I'm wrong), it's pressing 303hp w 289lbf-ft. 0.1 litter smaller and it's pressing 47hp & 42lbf-ft difference... but of course this EZ36D engine is just a bored out EZ30R, so technically it's 3L block was bore to the limit. 2. Modification I have seen some shop swap the STI engine out and put EZ30R engine and put big turbo to press over 800hp... but we're talkin' bout over $20k of work and lasting the engine for few yrs and blow up. While v engine you spent half of that and make much or more hp and last longer. Those are the simple reasons why Quote:
|
[QUOTE=ichitaka05;14916]A lot of reason, but I'll just list 2
1. Power Power difference you can get out of V engine and boxer engine is ridiculous. For an example I'll use new Legacy 3.6R, which has 3.6L H6 engine. That engine name is EZ36D 3629CC DOHC, 260ps (256 hp) @6000rpm, 335Nm (247lbf-ft) @4400rpm. Top of my head, Toyota v6 engine that comes to mind is v6 engine from GS350, iirc it was 2GR-FE (correct me if I'm wrong), it's pressing 303hp w 289lbf-ft. 0.1 litter smaller and it's pressing 47hp & 42lbf-ft difference... but of course this EZ36D engine is just a bored out EZ30R, so technically it's 3L block was bore to the limit. 2. Modification I have seen some shop swap the STI engine out and put EZ30R engine and put big turbo to press over 800hp... but we're talkin' bout over $20k of work and lasting the engine for few yrs and blow up. While v engine you spent half of that and make much or more hp and last longer. Those are the simple reasons why /QUOTE] So are you saying they arent strong and cant make power because they are flat though? Or does it just happen that the ones they currently make don't output big numbers? I always thought the flat engines were smoother |
Quote:
Is the EZ36 really bored? I know its quite different to the EZ30D in almost every way... to the point you cant use any parts of the 30 on a 36 or vice verser. What I thought they did was they left the bore the same put went with flexible conrods to get the extra .6L One reason it is lower on power is due to being made to run on low grade crap gas, not perium |
Quote:
Like in the above quote I said the 3.6 has flexible con rods and they are made to run on the crap gas. Subaru wanted to increase the tourqe and power on the 3L with out increasing its size to much. So they went with flexible conrod to help. The flexible conrods wouldnt handle any FI. Sadly Subaru never has done a factory turbo 6.. If they had done that, it would had been alot cheaper to play with mod etc. The boxer motor is smooth. Even really ancient flat twins from 1910 where natually smooth. You could stand a old coin up on its edge and it would stay on top of the running motor with out falling off. I was walking past the local Subaru dealership a few years ago and they had the bonnets up on a few legacys... I stopped and looked. I didnt even realise they where running. I put my hand on the motor and didnt feel any vibration. I only realised they were running when I looked at the spinning pulleys. |
Quote:
I do side with him in that I'd prefer a V though. |
Quote:
TO ME YES, and I'm not the only one. Many articles state that the car is souless almost to a point where all of the computers are driving you instead of the other way around. Despite it's unquestionable supercar performance levels, in the fantasy world where I could afford one, I would never consider buying one because of the dual clutch transmission. If they offered a traditional 6 speed manual then I would be all over it. I have driven many cars with automatics and DCT's and I just don't like them. |
Quote:
Quote:
If you have chance to test drive current Legacy 3.6R or Tribeca check it out, I can guarantee Legacy GT is smoother. Quote:
|
Quote:
I will agree with you. I would prefer 3 peddles but technology is technology. And its growing everyday. What do you guys mean by flexible connecting rods? (im to lazy to search) |
Quote:
|
power production has zero, nada, nothing, zilch, to do with cylinder layout. NOTHING.
head, intake, and exhaust design make power. UGH. -Mike |
Quote:
MY STEREO! http://www.youtube.com/watch?v=z33tH-JdPDg |
| All times are GMT -4. The time now is 02:46 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
User Alert System provided by
Advanced User Tagging v3.3.0 (Lite) -
vBulletin Mods & Addons Copyright © 2026 DragonByte Technologies Ltd.