Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB

		Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > Search Forums
Search Results

Showing results 1 to 9 of 9
Search took 0.01 seconds. Search: Posts Made By: AxisPower

Forum: Engine Swaps

04-06-2021, 12:08 PM

Replies: 13

4A-GE 20v Blacktop

Views: 4,710

Posted By AxisPower

My 4age blacktop with cams and exhaust made...

My 4age blacktop with cams and exhaust made somewhere around 140 whp back in my ae86. In a car that weighs a lot less I guess thats fine, but it would be a pretty noticeable loss of power in a newer...

Forum: Brakes, Suspension, Chassis

09-12-2020, 05:15 PM

Replies: 2

Tein src csg spec

Views: 1,421

Posted By AxisPower

Tein src csg spec

Selling a set of of tein src's that I purchased last year. When I purchased them they had approximately 20,000 km according to the previous owner. I had them sent off to Tein to have them refreshed...

Forum: Mechanical Maintenance (Oil, Fluids, Break-In, Servicing)

05-05-2020, 02:45 PM

Replies: 43

Metal ball on the tranny drain plug magnet. What gives?

Views: 9,653

Posted By AxisPower

Just to avoid confusion, these are different from...

Just to avoid confusion, these are different from the detent balls that sit inside the shiftfork shafts. Those are much bigger than the one in OP's picture. Only way I could see this happening is if...

Forum: Mechanical Maintenance (Oil, Fluids, Break-In, Servicing)

05-05-2020, 01:51 PM

Replies: 43

Metal ball on the tranny drain plug magnet. What gives?

Views: 9,653

Posted By AxisPower

Since I just had the pleasure of taking my...

Since I just had the pleasure of taking my transmission apart I can tell you exactly what that is. Each hub/sleeve has 3 of these spring loaded balls. BRBA02 in the diagram....

Forum: Engine, Exhaust, Transmission

05-16-2019, 10:47 PM

Replies: 7

Differential shims source

Views: 1,942

Posted By AxisPower

I've setup two different rears for a brz and both...

I've setup two different rears for a brz and both times the pinion shim that came with the diff (in both cases a 1.97mm) always gave the best pattern. Side shims I've found usually a set of 2.80mm -...

Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing

07-17-2018, 09:00 PM

Replies: 20

SPL Rear Toe Links issues

Views: 3,973

Posted By AxisPower

I didn't completely read the OPs post, didn't...

I didn't completely read the OPs post, didn't realize it was the little clamp thats loosening up. My only thought is that on the rear lower control arm they offer, there are essentially 2 clamps: the...

Forum: Engine, Exhaust, Transmission

11-10-2017, 11:29 AM

Replies: 123

SARD ITB (4 Throttle) News!

Views: 32,129

Posted By AxisPower

Curious to see the results. Kind of lame though...

Curious to see the results. Kind of lame though they're charging 2k+ for a kit that uses 20 year old 20v 4age itbs that were originally for a 1.6l motor.

Forum: Engine, Exhaust, Transmission

01-24-2017, 02:32 PM

Replies: 50

SARD Surge Tank Kit w/ ITB from TAS 2017

Views: 24,134

Posted By AxisPower

Each ae111 throttle body is its own individual...

Each ae111 throttle body is its own individual unit, they're just held together with linkages which can be disassembled.

Forum: Member's Car Journals

03-30-2014, 09:15 PM

Replies: 5

Tofu Delivery Vehicle for The 21st Century

Views: 2,216

Posted By AxisPower

Fronts: 17x8 +35 with a 20mm adapter 205/45/17...

Fronts: 17x8 +35 with a 20mm adapter 205/45/17 dz101
Rear: 17x9 +38 with a 15mm adapter 225/45/17 dz101

Rear fitment is spot on at -1.5. Front is at -3 and still has some room. Probably could've...

Showing results 1 to 9 of 9

Forum Jump

All times are GMT -4. The time now is 12:03 PM.

User Name		Remember Me?
Password