follow ft86club on our blog, twitter or facebook.
FT86CLUB
Ft86Club
Delicious Tuning
Register Garage Community Calendar Today's Posts Search

Go Back   Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > Search Forums
Reload this Page Search Results


Showing results 1 to 15 of 15
Search took 0.79 seconds. Search: Posts Made By: fer3d
Forum: Cosmetic Modification (Interior/Exterior/Lighting) 11-27-2020, 02:02 PM
Replies: 1
Views: 2,254
Posted By MrDignified
Widebody Fender Width Compile

I’m trying to compile fender widths for widebody kits. I’ve gone through the brand owners websites, forums/reddit etc. So far this is what I’ve come up with. I’m sure I’ve missed other kits, so if...
Forum: Issues | Warranty | Recalls / TSB 02-03-2020, 06:41 AM
Replies: 87
Views: 19,302
Posted By tomm.brz
f*ck it. I removed battery, i reflashed,...

f*ck it.

I removed battery, i reflashed, performed a cold start.. vvt didnt enable
i did the procedure that was posted in the previous page (10 sec idle, 20 sec 97km/h ecc ecc)
vvt didn t...
Forum: Forced Induction 07-23-2019, 10:44 AM
Replies: 1,238
Views: 475,873
Posted By rb6freak
Pretty much any vacuum line will work. Since I...

Pretty much any vacuum line will work. Since I already Tee'd off the brake booster, I put a distribution block off that T and put a reference line going through the firewall to my gauge.

...
Forum: Tracking / Autocross / HPDE / Drifting 01-13-2019, 07:33 PM
Replies: 3
Views: 3,442
Posted By VerusEric
Are Flat Floors Necessary For Diffusers to Function?

If you would rather watch than read: https://www.youtube.com/watch?v=Zq2KjcNE50c&t=204s


In this post, we dive into a common incorrect perception that a flat underbody is necessary and vital for...
Forum: Brakes, Suspension, Chassis 01-01-2019, 08:38 PM
Replies: 17
Views: 8,115
Posted By red_rocket
Project Mu Full BBK and Tein Control Master Coilovers

Hello,

I have a Project Mu big brake kit (front and rear). Everything included for installation. It was installed on a Subaru BRZ and was daily driven for roughly 10k miles. Never tracked. ...
Forum: DIY (Do-It-Yourself) Guides 09-08-2018, 06:20 PM
Replies: 8
Views: 11,640
Posted By Mermoz
DIY : Draining the gas tank - Methods to empty fuel tank

Hello,

When I decided to switch to E85 from RON98, I wanted to completely empty my fuel tank. I tried 3 different methods, here is my feedback.


Important note: be extremely carreful when...
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 06-15-2018, 05:26 PM
Replies: 13
Views: 3,097
Posted By Code Monkey
Pad looks ok, I wouldn't worry about the missing...

Pad looks ok, I wouldn't worry about the missing corner.
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 06-13-2018, 08:42 PM
Replies: 13
Views: 3,097
Posted By jmimac351
Yep. Need to add cooling. I've run the Ferodo...

Yep. Need to add cooling. I've run the Ferodo DS1.11 pad based on the recommendation of Jeff Ritter at Essex Parts Service after I shared with him what I was looking for. I LOVED them. Great...
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 06-13-2018, 08:08 PM
Replies: 13
Views: 3,097
Posted By CSG Mike
Cracked edges are a result of overheating + lack...

Cracked edges are a result of overheating + lack of chamfering. It is normal for what you are doing to the pad.
Forum: Forced Induction 05-30-2018, 08:02 PM
Replies: 24
Views: 7,789
Posted By CSG Mike
oldschool brute force: drop compression and push...

oldschool brute force: drop compression and push tons of boost.

New school efficiency: high compression, moderate boost.

Notice that OEMS are all the latter now. They're not stupid; OEMs...
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 10-17-2016, 01:43 AM
Replies: 12
Views: 2,161
Posted By RJasonKlein
Calling All Chassis Gurus - What's the Best Method for Adjusting Front Camber?

Here's a theoretical and practical question for those that understand chassis engineering and setup better than I: For a car like mine that is equipped with SPL Parts adjustable front lower control...
Forum: Forced Induction 03-29-2016, 01:29 PM
Replies: 1
Views: 6,068
Posted By mrk1
PCV System in Pictures

I have a motor apart in my garage and thought I would take some photos to show just where the different ports go.

There seems to be some debate about if both lines need to go to a catch can, or...
Forum: DIY (Do-It-Yourself) Guides 03-22-2016, 09:47 PM
Replies: 0
Views: 6,986
Posted By nickw14
Head Removal

So I have searched around a bit an was unable to find a good (or any) head removal tutorial. I decided I'd throw one together since I need to pull mine anyway. I wrote this tutorial after I already...
Forum: Software Tuning 11-15-2015, 12:30 AM
Replies: 139
Views: 61,338
Posted By ztan
TRAC switch doubleclick

Off topic, but related.

With the Arduino Nano going in as a FlexFuel Sensor controller, there is space for much more to be added on. I decided to make a doubleclick TRAC control switch so I don't...
Forum: Wheels | Tires | Spacers | Hub -- Sponsored by The Tire Rack 06-02-2012, 02:39 AM
Replies: 632
Views: 1,581,728
Posted By DarrenDriven
FR-S / BRZ Wheel Directory, Gallery and Fitment Guide Chart

http://www.darrendriven.com/ft86/title.png (http://tinyurl.com/86wheels)
Mods/Admin DIY Update Topic: http://www.ft86club.com/forums/showthread.php?t=80971

EVERY SINGLE new topic that is posted...
Showing results 1 to 15 of 15

 
Forum Jump

All times are GMT -4. The time now is 07:58 AM.

Contact Us - Toyota GR86, 86, FR-S and Subaru BRZ Forum - FT86CLUB - Archive - Privacy Statement - Terms of Service/DMCA Policy - Top

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.

Garage vBulletin Plugins by Drive Thru Online, Inc.