Spektyr
|
Last Activity: 03-24-2023 08:34 PM
Trader Rating
| iTrader Profile | Recent Ratings | ||||||||||||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||||||||||
Positive
Neutral
Negative
Mentions
| 05-24-2021 |
| 11:02 AM - Dadhawk mentioned Spektyr in post A few basic questions ...r a 2022 GR86. .
Spektyr welcome to the forum... |
Quotes
| 03-25-2023 |
| 03:38 PM - DocWalt quoted Spektyr in post Official FT86Club 3D printing thread! What's the dimensions on tha... |
| 03-22-2023 |
| 12:47 AM - rennlistuser3 quoted Spektyr in post Toyota GR86 v Mazda MX-5 v Alpine A110 GT (EVO Magazine Review) As much as the kid in me wan... |
| 03-15-2023 |
| 04:44 PM - Spektyr quoted removedonut in post Dealer Software Customization I’ve used techstream V18 success... |
| 03-14-2023 |
| 11:15 AM - removedonut quoted Spektyr in post Dealer Software Customization I remember reading that Gen1... |
| 11:12 AM - dragoontwo quoted Spektyr in post Dealer Software Customization That link, this thread, and ... |
| 11:07 AM - Spektyr quoted dragoontwo in post Dealer Software Customization I don't know asbout Techstream,... |
| 11:02 AM - dragoontwo quoted Spektyr in post Dealer Software Customization I remember reading that Gen1... |
| 10:59 AM - Spektyr quoted removedonut in post Dealer Software Customization https://www.ft86club.com/forums/... |
| 03-13-2023 |
| 02:57 PM - removedonut quoted Spektyr in post Dealer Software Customization Can someone confirm this?
I ... |
| 03-02-2023 |
| 01:47 PM - Spektyr quoted VoltsFRS2013 in post Solution for Silicone in the Oil Pickup by Killer B Motorsport - Beta Testers Needed The "issues" with the new gen are... |
| 02-16-2023 |
| 09:08 AM - Spektyr quoted x808drifter in post Owners Manual Oil Anomaly I don't see 85 anywhere on what ... |
| 02-06-2023 |
| 10:11 PM - treedodger quoted Spektyr in post Trueno Blue GR86 Thread I went with the tinted film ... |
| 02-03-2023 |
| 03:39 PM - NoHaveMSG quoted Spektyr in post Official FT86Club 3D printing thread! Good point.
PC (Polycarbona... |
| 03:25 PM - Spektyr quoted NoHaveMSG in post Official FT86Club 3D printing thread! Just don't get any brake fluid... |
| 03:13 PM - NoHaveMSG quoted Spektyr in post Official FT86Club 3D printing thread! ABS is good to 105C / 220F. ... |
| 01:41 PM - Racecomp Engineering quoted Spektyr in post Official FT86Club 3D printing thread! Yup. PLA gets soft around 55... |
| 01:00 PM - Spektyr quoted Racecomp Engineering in post Official FT86Club 3D printing thread! To be clear, don't print these in regular... |
| 01-18-2023 |
| 02:23 PM - zeroomega quoted Spektyr in post Oil pressure drops on race track in S corners This is probably too simple ... |
| 01:25 PM - NoHaveMSG quoted Spektyr in post Oil pressure drops on race track in S corners This is probably too simple ... |
| 01-13-2023 |
| 10:02 AM - Tcoat quoted Spektyr in post End of the era Yep. We took a bus tour in S... |