mkodama
|
Last Activity: 01-24-2026 05:06 PM
Trader Rating
| iTrader Profile | Recent Ratings | ||||||||||||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||||||||||
Positive
Neutral
Negative
Contact Info
- Home Page
- https://86challenge.us/
- This Page
- https://www.ft86club.com/forums/member.php?u=141159
Quotes
| 07-09-2025 |
| 01:37 AM - NoHaveMSG quoted mkodama in post Compression Ratio Change 12.5:1 to 13.5:1 ...ttps://datazap.me/u/mkodama/log-1748279724?log=0... |
| 07-06-2025 |
| 03:18 PM - mkodama quoted NoHaveMSG in post Compression Ratio Change 12.5:1 to 13.5:1 I’m assuming a few factors. Cu... |
| 06-21-2025 |
| 02:23 PM - mkodama quoted tomm.brz in post Data Logs! Post them here. make it leaner and raise igni... |
| 09:28 AM - tomm.brz quoted mkodama in post Data Logs! Post them here. ...ttps://datazap.me/u/mkodama/log-1748279724?log=0... |
| 04-14-2025 |
| 06:54 AM - mkodama quoted norcalpb in post Found a solution to the P0193 CEL I hope it lasts a while too. ... |
| 12:06 AM - norcalpb quoted mkodama in post Found a solution to the P0193 CEL Sensor makes the most sense.... |
| 04-13-2025 |
| 02:38 AM - mkodama quoted norcalpb in post Found a solution to the P0193 CEL I need a few more test drives... |
| 04-12-2025 |
| 06:02 PM - norcalpb quoted mkodama in post Found a solution to the P0193 CEL Yep, those are all the parts... |
| 04-04-2025 |
| 04:29 PM - NoHaveMSG quoted mkodama in post Engine cranking but not running after rebuild. I timed it 180 degrees off! ... |
| 03:02 AM - mkodama quoted NoHaveMSG in post Engine cranking but not running after rebuild. It sounds like the crankshaft ... |
| 03:02 AM - mkodama quoted Tokay444 in post Engine cranking but not running after rebuild. It sounds like the crankshaft... |
| 02:37 AM - mkodama quoted norcalpb in post Found a solution to the P0193 CEL To be honest I'm not too sure... |
| 04-03-2025 |
| 01:29 PM - norcalpb quoted mkodama in post Found a solution to the P0193 CEL I have a 2017 engine so I al... |
| 03:49 AM - mkodama quoted norcalpb in post Found a solution to the P0193 CEL When you rebuilt your engine,... |
| 04-02-2025 |
| 11:46 PM - norcalpb quoted mkodama in post Found a solution to the P0193 CEL Thanks, good to know.
I was... |
| 03-30-2025 |
| 04:43 AM - mkodama quoted tomm.brz in post Found a solution to the P0193 CEL i have 1065 flashes on my ecu... |
| 01-11-2025 |
| 01:56 AM - mkodama quoted Tokay444 in post Upper oil pan baffle prototyping So only a LITTLE worse head d... |
| 01-08-2025 |
| 01:13 PM - callisto quoted mkodama in post Main bearing oil clearance measuring out of spec I wish there was more data o... |
| 12:58 PM - mkodama quoted Eaton PSI in post Main bearing oil clearance measuring out of spec There is always the chance tha... |
| 09:04 AM - Grady quoted mkodama in post Main bearing oil clearance measuring out of spec I don’t get my equipment cal... |