Kraftwerks Supercharger Owners Thread - Page 133 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Jcl · 07-31-2014, 12:11 AM

Anyone have problems with the car not holding idle after kws map?

mit_peid · 07-31-2014, 01:19 AM

Quote:

Originally Posted by Jcl

Anyone have problems with the car not holding idle after kws map?

Did you change the map sensor to the KW map sensor and not the denso one that originally came with kit?

zERoTu · 07-31-2014, 05:20 AM

Quote:

Originally Posted by Jcl

Anyone have problems with the car not holding idle after kws map?

I have same problem too. And there is a kw map sensor? I got the denso one.

Jcl · 07-31-2014, 09:38 AM

Name: ImageUploadedByTapatalk1406813886.178805.jpg
Views: 1226
Size: 309.1 KB

This is what came with.

captain_jack · 07-31-2014, 01:30 PM

That's the one included in the kit, it doesn't look like mine but I have an earlier kit. The newer kits have that one. I'd call them if it were me.

Jcl · 07-31-2014, 08:21 PM

Thanks to Joe @KraftWerks I am up and running. Looks like the map sensor they sent was a 2.5bar vs their regular ones.

KraftWerks · 07-31-2014, 08:50 PM

Quote:

Originally Posted by Jcl

Thanks to Joe @KraftWerks I am up and running. Looks like the map sensor they sent was a 2.5bar vs their regular ones.

Glad we could help!

zoth · 07-31-2014, 10:48 PM

Anyone have pics of the oil cooler kit installed? Thanks...

Freeman · 07-31-2014, 11:00 PM

Quote:

Originally Posted by zoth

Anyone have pics of the oil cooler kit installed? Thanks...

Name: ImageUploadedByTapatalk1406861980.629703.jpg
Views: 1075
Size: 249.7 KB

Name: ImageUploadedByTapatalk1406861994.210667.jpg
Views: 995
Size: 247.0 KB

That's all I got for now

If you need me to snap some more I can try

Also the instructions don't mention it, but clamp the ends of the lines. Otherwise lines will pop off....

KraftWerks · 08-01-2014, 12:47 PM

Quote:

Originally Posted by Freeman

Attachment 86727 Attachment 86728

That's all I got for now

If you need me to snap some more I can try

Also the instructions don't mention it, but clamp the ends of the lines. Otherwise lines will pop off....

@Freeman - The line and fittings are rated to up to 250psi without a clamp. You should not have any issues with these while running without clamps.

Freeman · 08-01-2014, 01:09 PM

Quote:

Originally Posted by KraftWerks

@Freeman - The line and fittings are rated to up to 250psi without a clamp. You should not have any issues with these while running without clamps.

And according to the instructions the lines and fittings are supposed to come pre-assembled. Mine weren't so I assembled myself. I should have put hose clamps on them, rookie mistake. Then this happened....

Attachment 86803 Attachment 86804 Attachment 86805 Attachment 86806

... So I say again, good idea to put hose clamps on.

Calum · 08-01-2014, 06:18 PM

Quote:

Originally Posted by Freeman

And according to the instructions the lines and fittings are supposed to come pre-assembled. Mine weren't so I assembled myself. I should have put hose clamps on them, rookie mistake. Then this happened....

Attachment 86803 Attachment 86804 Attachment 86805 Attachment 86806

... So I say again, good idea to put hose clamps on.

The link is broken.

CSG Mike · 08-01-2014, 08:05 PM

Quote:

Originally Posted by KraftWerks

@Freeman - The line and fittings are rated to up to 250psi without a clamp. You should not have any issues with these while running without clamps.

Key words.. "up to". Not "at least".

KraftWerks · 08-01-2014, 08:31 PM

Quote:

Originally Posted by CSG Mike

Key words.. "up to". Not "at least".

We're not quite sure what your motor is referencing but the average pressure on one of these motors at operating temperature would be something like 80-105psi at a maximum? This would not come close to even an 'up to' rating.

07-31-2014, 10:48 PM	#1856
zoth Senior Member Join Date: Aug 2013 Drives: 2013 BRZ Premium Dark Gray Metallic Location: McAllen, TX Posts: 534 Thanks: 306 Thanked 199 Times in 127 Posts Mentioned: 18 Post(s) Tagged: 0 Thread(s)	Anyone have pics of the oil cooler kit installed? Thanks... __________________ KraftWerks SuperCharger C30=HB-Waterless Coolant-(Mishi)Racing Thermostat & Oil Can Tomei EL-PLM Overpipe-HKS Dual Resonated Front Pipe-Invidia N1 DR31 18x9+38 Square w/ 255/40r18 PT-722, TRD Quickshifter, ACT Streetlite Kit Moto-East Flex-Fuel Kit (Almost running 100% E85 all the time) DW 700 cc Injectors-Tune by (Moto-East)-KW Oil Cooler

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Innovate (Sprintex) Supercharger Owners Topic	DarrenDriven	Forced Induction	9139	12-29-2023 10:58 PM
Kraftwerks Rotrex Supercharger Discussion	nelsmar	Forced Induction	697	01-18-2022 12:06 PM
All SUPERCHARGER kits compilation thread	subatoy	Forced Induction	76	03-10-2016 12:38 PM
Kraftwerks Supercharger??	umpadupa	Forced Induction	1	08-05-2013 05:27 PM

07-31-2014, 12:11 AM	#1849
Jcl Senior Member Join Date: Feb 2014 Drives: 2014 BRZ Location: Alberta, Canada Posts: 189 Thanks: 19 Thanked 23 Times in 17 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	Anyone have problems with the car not holding idle after kws map?

07-31-2014, 09:38 AM	#1852
Jcl Senior Member Join Date: Feb 2014 Drives: 2014 BRZ Location: Alberta, Canada Posts: 189 Thanks: 19 Thanked 23 Times in 17 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	This is what came with.

07-31-2014, 01:30 PM	#1853
captain_jack Senior Member Join Date: Sep 2012 Drives: '13 raven frs, '10 taco,09 gsxr 600 Location: Tucson AZ Posts: 1,342 Thanks: 530 Thanked 394 Times in 297 Posts Mentioned: 81 Post(s) Tagged: 0 Thread(s)	That's the one included in the kit, it doesn't look like mine but I have an earlier kit. The newer kits have that one. I'd call them if it were me.

07-31-2014, 08:21 PM	#1854
Jcl Senior Member Join Date: Feb 2014 Drives: 2014 BRZ Location: Alberta, Canada Posts: 189 Thanks: 19 Thanked 23 Times in 17 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	Thanks to Joe @KraftWerks I am up and running. Looks like the map sensor they sent was a 2.5bar vs their regular ones.

User Name		Remember Me?
Password