09-17-2012, 09:20 PM | #85 | |
Senior Member
Join Date: Jul 2012
Drives: GTS 86
Location: Australia
Posts: 989
Thanks: 873
Thanked 475 Times in 272 Posts
Mentioned: 12 Post(s)
Tagged: 1 Thread(s)
|
3D vinyl vs 3M Di Noc
Quote:
Hi there mate, I was wondering how would you compare this product with 3m di Noc. I have worked with DiNoc extensively and I am quite happy with the way it shapes and everything. However, your film looks game, and I really like it. How doe it feel when you touch it? Does it have that CF dry feel (like Dinoc) or it's smooth? Also, how easy does it go around difficult shapes? Is the adhesive good enough or strong enough? Is this a bit shinnier than the DiNoc 3M? Good job by the way, it looks good. |
|
09-18-2012, 02:35 AM | #86 | |
Join Date: Jun 2012
Drives: Sonic Blue 86 GTS 6AT
Location: Cairns
Posts: 360
Thanks: 147
Thanked 155 Times in 83 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Feeling wise - you can feel the CF texturing and strength of adhesive is good. When I was re-doing the centre dash pieces around the HVAC controls, I had to warm the vinyl up to get it off easily otherwise I found it only coming off in little bits, once warmed up it came off in one or two large pieces. In regards of ease of use and shaping I had no issues, it softens really easily with a hairdryer, molds well to corners etc and easy to stretch out creases. I am looking at some 3M di-Noc to cover the two dash board pieces due to a problem that I discuss in this thread: http://www.ft86club.com/forums/showthread.php?t=17380 I am hoping with the air release channels, there'll be less heating and stretching involved and less chance of further damage to my dashboard pieces. Due to price of the eBay stuff it was more of a cheap solution to try out to see if a) I was any good at it and b) if I liked the effect. That way if either a or b failed it wasn't going to be a lot of money down the drain. Having seen the effect now and liking the product I'm not adverse to shelling out a bit more $$$$ to finish off the dash board pieces. I would have had to buy some more anyway to finish these two pieces off and I reckon the 3M shouldn't cost too much more for a small area. Hope this helps. |
|
09-25-2012, 02:56 AM | #87 | |
Memphis
Join Date: May 2012
Drives: 1989 MR2 S/C, 2014 Scion FR-S
Location: Langley, B.C.
Posts: 559
Thanks: 270
Thanked 98 Times in 78 Posts
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
|
I want. Where did you get it?
Quote:
__________________
"It's ok... It's not structural."- Mikey
|
|
09-25-2012, 02:59 AM | #88 |
Join Date: Jun 2012
Drives: Sonic Blue 86 GTS 6AT
Location: Cairns
Posts: 360
Thanks: 147
Thanked 155 Times in 83 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
|
09-25-2012, 03:01 AM | #89 | |
Join Date: Jun 2012
Drives: Sonic Blue 86 GTS 6AT
Location: Cairns
Posts: 360
Thanks: 147
Thanked 155 Times in 83 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
Quote:
|
|
09-25-2012, 03:02 AM | #90 |
Memphis
Join Date: May 2012
Drives: 1989 MR2 S/C, 2014 Scion FR-S
Location: Langley, B.C.
Posts: 559
Thanks: 270
Thanked 98 Times in 78 Posts
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
|
Sweet for you, not for me...$$?? lol
__________________
"It's ok... It's not structural."- Mikey
|
09-25-2012, 03:06 AM | #91 |
Join Date: Jun 2012
Drives: Sonic Blue 86 GTS 6AT
Location: Cairns
Posts: 360
Thanks: 147
Thanked 155 Times in 83 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
|
09-25-2012, 08:34 PM | #93 |
Senior Member
Join Date: Jul 2012
Drives: GTS 86
Location: Australia
Posts: 989
Thanks: 873
Thanked 475 Times in 272 Posts
Mentioned: 12 Post(s)
Tagged: 1 Thread(s)
|
3M Dinoc
Cheers mate, looking forward to it. By the sounds of it, it would be very similar to Dinoc 3M, but I will weait for your feedback first. I have some Dinoc left overs at home I could use to do my GTS when it comes.
|
The Following User Says Thank You to Hawk77FT For This Useful Post: | Sutty (09-26-2012) |
09-26-2012, 02:20 AM | #95 |
Join Date: Jun 2012
Drives: Sonic Blue 86 GTS 6AT
Location: Cairns
Posts: 360
Thanks: 147
Thanked 155 Times in 83 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
Yes
This store normally has them - sold out at the moment by the looks of it: http://stores.ebay.com.au/SydneyCityParts?_rdc=1 |
09-26-2012, 02:23 AM | #96 |
Join Date: Jun 2012
Drives: Sonic Blue 86 GTS 6AT
Location: Cairns
Posts: 360
Thanks: 147
Thanked 155 Times in 83 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
|
09-26-2012, 02:28 AM | #97 |
Join Date: Jun 2012
Drives: Sonic Blue 86 GTS 6AT
Location: Cairns
Posts: 360
Thanks: 147
Thanked 155 Times in 83 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
Here's the latest addition to Hedgehog, my @GrimmSpeed Limited Edition oil filler cap, it's as good as it looks:
I'm also down to get the matching L.E. battery tie down. Nice bit of under bonnet bling. Thanks to @cto424 too for selling it to me |
|
|
|
|