follow ft86club on our blog, twitter or facebook.
FT86CLUB
Ft86Club
Speed By Design
Register Garage Members List Calendar Search Today's Posts Mark Forums Read

Go Back   Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > Technical Topics > Mechanical Maintenance (Oil, Fluids, Break-In, Servicing)

Mechanical Maintenance (Oil, Fluids, Break-In, Servicing) Everything related to the mechanical maintenance of the FR-S and BRZ


User Tag List

Reply
 
Thread Tools Search this Thread
Old 05-24-2015, 04:58 PM   #1
Scenic Driver
Senior Member
 
Join Date: Feb 2013
Drives: 13 Subaru BRZ, 02 Audi TTQ
Location: Orange County, NY
Posts: 456
Thanks: 61
Thanked 320 Times in 168 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Changing spark plugs

So the car is at around 66k miles so it was time to do the plugs. It's certainly not a job I would want to do often but if you have patience and can work in tight spaces it's not terrible to do. If you do not have a lot of DIY experience you may want to consider paying someone to do this.

Like any other writeup on the internet, if you mess up your car while following this it's your responsibility not mine.



Right side plugs
Remove the injector ecu (10mm bolts x 3), the bottom one is a little annoying. Don't unplug the wiring from the ecu, there's enough slack on the wiring that you can just squeeze it past the hose and move it toward the back of the engine.




Remove the 10mm bolt and unclip the wiring from each of the coil packs and remove them.



You can now remove the spark plugs. Here's the tools I used, if I had another small extension I would have tried that instead of the universal joint but I didn't feel like running to the store. The mini ratchet isn't necessary but I found it helpful. Also, make sure you have a magnet on a stick, the potential for dropping stuff is high, I actually tethered my ratchets to the car with some twine.



I always prefer to insert and start threading the plugs with a piece of vacuum line or an old spark plug boot.



Left side plugs

Because of all of the lines and hoses running on this side there's even less room to work. To get a little more room I removed the bolts from the injector cover (12mm) and to keep from rubbing the shit out my arm I also removed the clip that holds the 3 hoses (it just unclips from the metal bracket). If you have thick arms you may want to remove the strut brace (and master cylinder brace if you have one) as well. It was just too difficult to get good pics of this side but it's not any different than the other side.
__________________
Scenic Driver is offline   Reply With Quote
The Following 43 Users Say Thank You to Scenic Driver For This Useful Post:
8R6 (11-20-2015), BillyStrato (07-18-2016), Black Tire (05-25-2015), Bonburner (05-24-2015), brzbrad (02-14-2017), Carlitoz3 (06-03-2015), civicdrivr (05-26-2015), Dadhawk (05-25-2015), DocWalt (06-16-2015), drewbot (05-09-2016), DustinS (06-05-2015), D_Thissen (12-07-2018), FR-S Future Owner (06-22-2016), FunnyGopher (07-04-2018), Gen3MR2 (08-22-2016), GhostOp86 (05-25-2015), GotBRZ1691 (06-05-2015), hmong337 (05-25-2015), humfrz (05-25-2015), jcw99 (02-27-2016), jliongh (05-23-2018), JMon85 (05-05-2018), Kaotic Lazagna (05-25-2015), Keenercarguy (10-20-2017), Muaddib (05-26-2015), mx5 2nr (04-21-2016), Myv (05-24-2015), Pacific (05-25-2015), pooch (10-10-2016), PoorMansRacing (12-02-2015), Satanasso (11-17-2017), series420 (03-25-2021), Shoebox (08-28-2016), smg1138 (06-14-2017), spdfreak (05-25-2015), steve86gt (08-12-2016), Takumi788 (11-15-2016), Tcoat (05-25-2015), Teseo (04-26-2017), Tt3Sheppard (06-03-2015), waterbison777 (10-12-2016), wbradley (05-24-2015), zc06_kisstherain (06-16-2015)
Old 05-24-2015, 10:08 PM   #2
Myv
Senior Member
 
Myv's Avatar
 
Join Date: Dec 2012
Drives: SWP BRZ Limited MT
Location: Thornhill, Ont, Canada
Posts: 531
Thanks: 124
Thanked 113 Times in 82 Posts
Mentioned: 6 Post(s)
Tagged: 1 Thread(s)
Myv is offline   Reply With Quote
Old 05-24-2015, 10:11 PM   #3
BRZtoni
Turbo E85
 
BRZtoni's Avatar
 
Join Date: Sep 2013
Drives: 13 wrb brz
Location: torrance, ca
Posts: 1,093
Thanks: 172
Thanked 555 Times in 349 Posts
Mentioned: 32 Post(s)
Tagged: 0 Thread(s)
teach me more!
__________________
Flex Fuel Turbo BRZ
BRZtoni is offline   Reply With Quote
Old 05-25-2015, 06:53 AM   #4
hmong337
Emperor JDM
 
hmong337's Avatar
 
Join Date: Jun 2013
Drives: '91 MR2 Gen3 3SGTE, '13 FRS
Location: Onterrible, Canada
Posts: 1,750
Thanks: 3,498
Thanked 909 Times in 495 Posts
Mentioned: 20 Post(s)
Tagged: 3 Thread(s)
Subbed
__________________
hmong337 is offline   Reply With Quote
Old 05-25-2015, 01:31 PM   #5
humfrz
Senior Member
 
Join Date: May 2013
Drives: 2013 FR-S, white, MT
Location: Puyallup, WA
Posts: 29,861
Thanks: 28,777
Thanked 31,796 Times in 16,418 Posts
Mentioned: 707 Post(s)
Tagged: 2 Thread(s)
Quote:
Originally Posted by Scenic Driver View Post
So the car is at around 66k miles so it was time to do the plugs. It's certainly not a job I would want to do often but .
Good write up, there Scenic Driver ......thanks for posting ......

I think when my FR-S gets up to that point ..... I'll just trade it in .....

Oh, the "good old days", ...... just open the hood, climb in the engine compartment and change the plugs; a 5 minute job.....


humfrz
Attached Images
 
humfrz is offline   Reply With Quote
The Following 5 Users Say Thank You to humfrz For This Useful Post:
chaoskaze (08-07-2016), civicdrivr (05-26-2015), Dadhawk (05-25-2015), lantsalot (05-22-2018), sroby (07-16-2019)
Old 05-25-2015, 02:11 PM   #6
Scenic Driver
Senior Member
 
Join Date: Feb 2013
Drives: 13 Subaru BRZ, 02 Audi TTQ
Location: Orange County, NY
Posts: 456
Thanks: 61
Thanked 320 Times in 168 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by humfrz View Post
Oh, the "good old days", ...... just open the hood, climb in the engine compartment and change the plugs; a 5 minute job.....
If it was an I4 engine it would probably only take 10 minutes, that's all it takes on my Audi.
__________________
Scenic Driver is offline   Reply With Quote
Old 05-26-2015, 12:32 PM   #7
GotMunchies?
Senior Member
 
Join Date: Feb 2014
Drives: '14 WRB BRZ 6MT Limited
Location: United States
Posts: 105
Thanks: 4
Thanked 75 Times in 39 Posts
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Wait... that's it?

No removing engine mounts and jacking the engine up? No soaking two piece plugs in PB Blaster and praying to the car gods they don't break when removing them? (Looking at you Ford Mod V8's) No enlisting seven year olds with slender wrists to grab them from under the firewall? (Looking at you, GM W Bodies)
GotMunchies? is offline   Reply With Quote
The Following User Says Thank You to GotMunchies? For This Useful Post:
MJones_RB (12-18-2018)
Old 05-26-2015, 12:40 PM   #8
aghuman
Senior Member
 
aghuman's Avatar
 
Join Date: Mar 2013
Drives: 2013 Asphalt FR-S
Location: Toronto, ON
Posts: 222
Thanks: 116
Thanked 53 Times in 30 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Thanks for this write up, Im getting to the point I need to change mine too and was debating doing it myself so this definitely helps. If anyone has done this or is planning to do this, are you just using OEM plugs or changing to something else?
aghuman is offline   Reply With Quote
Old 05-26-2015, 04:27 PM   #9
Scenic Driver
Senior Member
 
Join Date: Feb 2013
Drives: 13 Subaru BRZ, 02 Audi TTQ
Location: Orange County, NY
Posts: 456
Thanks: 61
Thanked 320 Times in 168 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by GotMunchies? View Post
Wait... that's it?

No removing engine mounts and jacking the engine up? No soaking two piece plugs in PB Blaster and praying to the car gods they don't break when removing them? (Looking at you Ford Mod V8's) No enlisting seven year olds with slender wrists to grab them from under the firewall? (Looking at you, GM W Bodies)
Unbolting the engine from the mounts and jacking it up is the way the service manual says to do it but as myself and others have found, it's not the only way.
__________________
Scenic Driver is offline   Reply With Quote
Old 05-26-2015, 06:01 PM   #10
Muaddib
Mentat
 
Muaddib's Avatar
 
Join Date: Jun 2013
Drives: 2013 Scion FRS 6MT
Location: Vancouver
Posts: 542
Thanks: 666
Thanked 358 Times in 198 Posts
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Lifting the motor to replace the plugs is just another way for Toyota to "lighten" up your wallet.
Muaddib is offline   Reply With Quote
The Following 4 Users Say Thank You to Muaddib For This Useful Post:
ddevl_86 (02-26-2021), FRSBRZGT86FAN (02-08-2016), hmong337 (11-20-2015), MaXimus (02-23-2016)
Old 05-26-2015, 09:23 PM   #11
Fastbrew
Senior Member
 
Join Date: Apr 2014
Drives: 2014 Pearl White BRZ
Location: USA
Posts: 764
Thanks: 123
Thanked 461 Times in 233 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
I am putting in a set of these soon:
HKS M50HL
Fastbrew is offline   Reply With Quote
The Following 3 Users Say Thank You to Fastbrew For This Useful Post:
aghuman (05-29-2015), chaoskaze (05-28-2015), zeal86 (02-25-2016)
Old 06-03-2015, 11:37 AM   #12
mreddie
Junior Member
 
Join Date: May 2015
Drives: 2015 BRZ
Location: Houston, Tx
Posts: 4
Thanks: 0
Thanked 1 Time in 1 Post
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
I'm a new owner here (1 month!), but it's good to see a successful alternative to changing plugs. Actually, lifting the engine slightly doesn't look too hard either - the mounts are easily accessible. I know changing plugs on some of the Ford V6 requires unplugging and removing the intake :-(
mreddie is offline   Reply With Quote
Old 06-03-2015, 02:27 PM   #13
Black Tire
Senior Member
 
Black Tire's Avatar
 
Join Date: Jun 2012
Drives: Whiteout Scion FR-S
Location: Minnesota
Posts: 508
Thanks: 367
Thanked 209 Times in 129 Posts
Mentioned: 5 Post(s)
Tagged: 1 Thread(s)
Garage
Great thread with some good tips!

I will be needing to change spark plugs soon, so I really appreciate this thread!

I guess we can be thankful the maintenance isn't as insane as a Ferrari F355. Here is a quote from an article on the subject (link below):

Quote:
What’s that? You heard “routine engine-out service”? Yes, ladies and gentlemen, that’s right: the F355 requires a complete engine-out service every three to five years in order to change the timing belts. This is another six to eight grand – remember, every three to five years – depending on where you do it. Some Ferrari dealers charge as much as $10,000. Although Ferrari is famous for these engine-out services, the 355 is the last modern model to require it.
Here’s Why You Should Never Buy A Ferrari F355
__________________
My cars always dress formally. They all wear black tires.

Black Tire is offline   Reply With Quote
Old 06-03-2015, 02:44 PM   #14
yaguphire
Senior Member
 
Join Date: Sep 2013
Drives: white-out FR-S
Location: Austin
Posts: 170
Thanks: 12
Thanked 15 Times in 14 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
nice write up. thank you.
yaguphire is offline   Reply With Quote
 
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Spark plugs for turbo whitefrs Forced Induction 88 05-05-2018 09:18 PM
boosted spark plugs? 350matt Forced Induction 9 08-09-2014 03:54 PM
Spark plugs Triumphrider Engine, Exhaust, Transmission 12 06-19-2014 10:47 AM
spark plugs subaruferrucci Engine, Exhaust, Transmission 22 04-10-2013 11:24 AM


All times are GMT -4. The time now is 08:45 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.

Garage vBulletin Plugins by Drive Thru Online, Inc.