|
Mechanical Maintenance (Oil, Fluids, Break-In, Servicing) Everything related to the mechanical maintenance of the FR-S and BRZ |
|
Thread Tools | Search this Thread |
01-29-2018, 01:17 PM | #1 |
Member
Join Date: Aug 2017
Drives: BRZ
Location: Asia
Posts: 48
Thanks: 7
Thanked 7 Times in 5 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Need advice... changing oil filter
Hello,
I am thinking to do a mid-interval EO & Oil Filter change myself. Have some question regarding the oil filter.... The Svc Manual state "Use an oil filter wrench with a size of 80 mm (3.15 in"), Is the tooling in the link the correct size for my Brz ? I suppose it will work on any Oil Filter that is compatible with Brz right, or at least most oil filter brand ? https://www.lazada.sg/sunshine-903-a...7376c303yVEgKk Also, if you dont have a torque meter, the Manual state "3/4 turn". That means upon "finger tight" (filter lip touching the base), you turn another 270deg right ? Thanks |
01-29-2018, 01:46 PM | #2 |
The Gunshine State
Join Date: Aug 2016
Drives: '14 BRZ Limited
Location: Florida
Posts: 1,463
Thanks: 631
Thanked 1,163 Times in 587 Posts
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
|
It all depends on which filter was used. The one in the link looks like it will fit the OEM filter and possibly 80% of all the filters out there.
I didn't need any tools when removing mine, it came off with a little elbow grease. I have only screwed them on until hand tight. Just check for leaks after you crank it up.
__________________
Current DD: M235i |
01-29-2018, 02:31 PM | #3 |
Senior Member
Join Date: Jun 2017
Drives: BRZ Yellow, 2019 Ranger, 2011 Evora
Location: Dallas
Posts: 1,685
Thanks: 352
Thanked 1,475 Times in 771 Posts
Mentioned: 14 Post(s)
Tagged: 1 Thread(s)
|
3/4 turn after touching is correct of you do not have torque wrench. This filter is easy to access so a wrench for removal should not be needed if installed and lubricated corect. Instead of oil use Dow Corning DC4 or equivalent to lubricate gasket when installing. Will make removal a lot easier.
|
01-29-2018, 03:24 PM | #4 |
Geo Tyrebighter Esq
Join Date: Mar 2013
Drives: '13 scion fr-s
Location: pnw
Posts: 4,186
Thanks: 6,323
Thanked 4,981 Times in 2,197 Posts
Mentioned: 39 Post(s)
Tagged: 1 Thread(s)
|
You don't need a specific wrench. The filter is on top and fairly easy to access.
I use a strap wrench since I already had one. Hand tighten only. Check each time that the gasket hasn't stuck onto the block and clean the surface. The FuMoto quick drain oil pan plug replacement comes in handy to get the old oil out. This should be torqued to spec, but that's only once and you won't strip the plug hole later.
__________________
--
"I gotta rock." -- Charley Brown |
01-29-2018, 03:39 PM | #5 |
Loading...████████] 99%
Join Date: Jul 2013
Drives: #0517
Location: southern california
Posts: 586
Thanks: 227
Thanked 251 Times in 171 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
The location of the filter makes it nice and easy, as mentioned. When removing, a strap wrench or one of these makes it a snap if hand-twist is not sufficient.
Tighten according to specifications in manual, check for leaks after installation.
__________________
R1 3 5
╘┼┼┤ . 2 4 6 |
01-29-2018, 04:49 PM | #6 |
Senior Member
Join Date: Jul 2012
Drives: BRZ
Location: ATL, GA
Posts: 1,021
Thanks: 289
Thanked 397 Times in 265 Posts
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
|
If you can't remove it by hand, just wait til the engine/filter is cold.. it'll twist off alot easier. If you can't remove it by hand when it's cold, then it was over-tightened when it was previously put on.
And yes, tighten it 3/4 turn once the filter touches the base is correct. |
01-29-2018, 08:37 PM | #7 |
Senior Member
Join Date: Nov 2015
Drives: Car
Location: Location
Posts: 646
Thanks: 374
Thanked 422 Times in 254 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
I use this oil filter tool with a ratchet to remove. For tightening I use hand tight + a little bit more.
|
01-29-2018, 08:39 PM | #8 |
Senior Member
Join Date: May 2013
Drives: 2013 FR-S, white, MT
Location: Puyallup, WA
Posts: 29,872
Thanks: 28,793
Thanked 31,826 Times in 16,429 Posts
Mentioned: 708 Post(s)
Tagged: 2 Thread(s)
|
Bubba says just to stick a screwdriver in it and turn ......
(however, Bubba's hands are so greasy, he can't get a grip on them ..... because he don't use none of those sissy blue shop gloves) humfrz |
The Following 2 Users Say Thank You to humfrz For This Useful Post: | gravitylover (01-30-2018), Tcoat (01-30-2018) |
01-30-2018, 08:14 AM | #9 |
Member
Join Date: Aug 2017
Drives: BRZ
Location: Asia
Posts: 48
Thanks: 7
Thanked 7 Times in 5 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Appreciate all the responses.
You guys must have strong hand. The only torque meter i have only goes up to 50 lbf-inc. (the manual torque setting is 14Nm / 124 Ibf-inc) Yes, i like the location of the oil filter Wouldnt bother if its beside the engine sump. (Dont have Jack Stand & my head cant clear the bottom gap) I intend to DIY every alternate EO change (by oil pump). So the wrench will be helpful. Rgds |
01-30-2018, 08:17 AM | #10 |
The Gunshine State
Join Date: Aug 2016
Drives: '14 BRZ Limited
Location: Florida
Posts: 1,463
Thanks: 631
Thanked 1,163 Times in 587 Posts
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
|
Well, I don't like to brag... lol.
Having a pump will eliminate the need to even jack up the car and crawl under (although with the Fumoto valve it makes it very easy and quick), I've been thinking about buying one too.
__________________
Current DD: M235i |
01-30-2018, 12:43 PM | #11 | |
Undisputed El Presidente
Join Date: Jun 2012
Drives: Zenki 37J ZN6
Location: Stockton, CA
Posts: 11,571
Thanks: 9,382
Thanked 9,397 Times in 5,261 Posts
Mentioned: 374 Post(s)
Tagged: 33 Thread(s)
|
Quote:
Fumoto plus ramps (I use Cusco Jack Assists ramps). No tools required |
|
01-30-2018, 01:01 PM | #12 |
Senior Member
Join Date: Jul 2014
Drives: 2020 Hakone
Location: London, Ont
Posts: 69,845
Thanks: 61,656
Thanked 108,284 Times in 46,456 Posts
Mentioned: 2495 Post(s)
Tagged: 50 Thread(s)
|
Was never a fan of the idea of pumping oil out. You don't get the same flushing effect and it can leave heavier bits and the worst sludge behind. Not that you should have heavier bits nor sludge but just in case...
__________________
Racecar spelled backwards is Racecar, because Racecar.
|
01-30-2018, 02:57 PM | #13 |
Senior Member
Join Date: Nov 2015
Drives: Car
Location: Location
Posts: 646
Thanks: 374
Thanked 422 Times in 254 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
|
01-30-2018, 02:59 PM | #14 |
Senior Member
Join Date: May 2013
Drives: 2013 FR-S, white, MT
Location: Puyallup, WA
Posts: 29,872
Thanks: 28,793
Thanked 31,826 Times in 16,429 Posts
Mentioned: 708 Post(s)
Tagged: 2 Thread(s)
|
|
The Following User Says Thank You to humfrz For This Useful Post: | 8RZ (01-30-2018) |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
TRD Intake Filter Air Filter Cleaner Element FRS BRZ 86 Toyota Racing Development | hirollaz | Engine, Exhaust, Bolt-Ons | 0 | 03-15-2017 02:46 AM |
Consensus on changing whole transmission versus changing solenoids | dem00n | Engine, Exhaust, Transmission | 7 | 07-20-2016 03:50 AM |
upload video of changing filter | Dr. BRZ | DIY (Do-It-Yourself) Guides | 5 | 11-14-2012 04:27 PM |
Drop In filter test! Stock, Apexi, No filter | RallySport Direct | Engine, Exhaust, Transmission | 14 | 06-25-2012 02:40 PM |