|
Forced Induction Turbo, Supercharger, Methanol, Nitrous |
|
Thread Tools | Search this Thread |
04-16-2018, 02:41 PM | #43 |
Senior Member
Join Date: Jan 2014
Drives: 2013 frs
Location: Miami fl
Posts: 206
Thanks: 38
Thanked 49 Times in 38 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Also any reason why I’m not getting a low fuel pressure code?
Sent from my iPhone using Tapatalk |
04-22-2018, 03:11 AM | #44 |
Senior Member
Join Date: Jan 2014
Drives: 2013 frs
Location: Miami fl
Posts: 206
Thanks: 38
Thanked 49 Times in 38 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
So I switched the tune and loaded both my tune from full blown and my stock tune and with both of them I had no maf sensor code.
As for my fuel pressure I have 2 high pressure pumps and a known good DI module. Low side fuel pressure is getting there confirmed with mechanical gauge but it doesn’t seem to be creating pressure. I disconnected the connector for the high pressure pump and checked with noid light to make sure it was receiving the signal and it is receiving it. This is a issue that I had at times before the built engine too just now on a completely larger scale. My fuel presussure on high side would randomly just drop. Normally I would turn the car off and let it cool down a bit and it came right back. I was thinking the fuel pressure sensor maybe? But again wouldn’t that throw a code? I bench tested as per service manual but from experience it doesn’t always mean it’s good even if you bench test it. Still fighting this issue please any help is appreciated!!! |
04-27-2018, 08:16 PM | #45 |
Senior Member
Join Date: Jan 2014
Drives: 2013 frs
Location: Miami fl
Posts: 206
Thanks: 38
Thanked 49 Times in 38 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Alright people idk if any of you are still keeping up with this thread but I hope this will help people that have my same issue in the future
I had everything I needed to run. Compression, air coming in, spark, and fuel Just didn’t have enough fuel pressure. My cylinder 1 and 4 spark plugs were sooty and cylinders 2 and 3 were looking good still. Car started but didn’t build fuel pressure nor idled properly So after what seemed like endless fault tracing and swapping parts I so happened to comment on a post on the gulf coast 86 Facebook page and the homie @Frs300 replied to the comment saving my sanity I was off timing on drivers side bank. Good thing is I was 180 off which then turned my compression to exhaust stroke and vise versa explaining why I had compression but the cam lobe was off for the high pressure pump so no pressure being built. Can’t thank you guys enough for all your Yelp fault tracing, now it’s time to break in my engine and pray nothing else happens lol Sent from my iPhone using Tapatalk |
The Following User Says Thank You to sid94 For This Useful Post: | Irace86.2.0 (04-27-2018) |
04-27-2018, 09:13 PM | #46 | |
Senior Member
Join Date: Sep 2017
Drives: 2022 BRZ Limited Silver
Location: Jacksonville, FL
Posts: 2,532
Thanks: 882
Thanked 2,045 Times in 1,188 Posts
Mentioned: 68 Post(s)
Tagged: 0 Thread(s)
|
Quote:
That’s great news. I just started rebuilding mine today. Destroyed a rod bearing on the way to work yesterday doing a pull to redline in 4th on the interstate. Oil level is to the top dot. I got mine with 83k and I’ve always felt it had a faint rod knock. Everyone on this forum said it’s normal for them to sound like ass so after about three months of stressing out over it I accepted that it really was just normal. Anyways, I think my plan right now is a short block. Tonight I started the engine pull. So far it’s been an easy project. All I have left is to unbolt the tranny and do the pull. I can’t wait to split the block and see if it’s seal material blocking flow to #4. |
|
04-27-2018, 09:17 PM | #47 | |
Senior Member
Join Date: Jan 2014
Drives: 2013 frs
Location: Miami fl
Posts: 206
Thanks: 38
Thanked 49 Times in 38 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Go for it man I haven’t had my car for 7 months so the excitement I have right now is beyond explanation Sent from my iPhone using Tapatalk |
|
04-27-2018, 10:37 PM | #49 | |
Senior Member
Join Date: Jan 2014
Drives: 2013 frs
Location: Miami fl
Posts: 206
Thanks: 38
Thanked 49 Times in 38 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
No my timing was off my cams were 180 off so nothing got bent it just took off timing cover and re did my timing Sent from my iPhone using Tapatalk |
|
04-28-2018, 12:02 AM | #50 |
Senior Member
Join Date: Mar 2017
Drives: Q5 + BRZ + M796
Location: Santa Rosa, CA
Posts: 7,884
Thanks: 5,668
Thanked 5,805 Times in 3,299 Posts
Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
|
Oh the whole camshaft was rotated 180 degrees? Both? Who did that one? You?
|
04-28-2018, 12:50 PM | #51 |
Senior Member
Join Date: Jan 2014
Drives: 2013 frs
Location: Miami fl
Posts: 206
Thanks: 38
Thanked 49 Times in 38 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
|
The Following User Says Thank You to sid94 For This Useful Post: | Irace86.2.0 (04-28-2018) |
04-28-2018, 02:59 PM | #52 |
Senior Member
Join Date: Mar 2017
Drives: Q5 + BRZ + M796
Location: Santa Rosa, CA
Posts: 7,884
Thanks: 5,668
Thanked 5,805 Times in 3,299 Posts
Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
|
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Building the engine for 400+hp | Dogster70 | Forced Induction | 20 | 07-16-2017 09:59 AM |
New motor - starting issue | protpibe | Engine Swaps | 24 | 06-01-2015 12:01 AM |
Starting issue? | winsometang | Issues | Warranty | Recalls / TSB | 7 | 11-26-2014 05:25 PM |
Starting issue | Hawaiian | Scion FR-S / Toyota 86 GT86 General Forum | 33 | 08-15-2013 07:40 AM |
Van starting issue-need advice. | LivingLegend | Off-Topic Lounge [WARNING: NO POLITICS] | 3 | 01-15-2013 10:48 PM |