BRZ 2017 Aluminum intake! MT6 - Page 2 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Gearbanger · 10-25-2016, 10:54 AM

Bump for update on these. Thanks

GsxrMe · 10-25-2016, 06:31 PM

Sorry, I added to your thread.

The intake looks sexy as hell but i'm going to wait for the install and do the block, and return style fuel system at the same time. Kinda want to do it the right way and save myself the trouble of dumping money into retunes and possible small issues to do nothing more than to change it again in a few months.

Work has been busy and the $$$ bonuses have been high. I got plenty of cash to dump into the BRZ as a project car. I finally finished my 1997 Wrangler and shes my daily as I pull the motor and take my time on the BURZ!

This thread won't be updated anytime soon, Figure 3 months of my engine sitting in my den on a engine stand.

mrk1 · 10-29-2016, 06:08 PM

Anyone have a part # for this?

Crazypinoy9 · 10-31-2016, 02:45 PM

Quote:

Originally Posted by mrk1

Anyone have a part # for this?

http://www.ft86speedfactory.com/suba...l#.WBeRFuArK70

mrk1 · 11-01-2016, 08:45 PM

Quote:

Originally Posted by Crazypinoy9

http://www.ft86speedfactory.com/suba...l#.WBeRFuArK70

Looking for OEM number, its 14001AC540 for anyone curious

GsxrMe · 11-02-2016, 08:16 PM

Ft86speedfactory.com has a very aggressive price, subi parts website is below

http://parts.subaru.com/p/MANIFOLD-C...4001AC540.html

Gearbanger · 11-29-2016, 09:54 PM

So who's installed this already. Lol easy swap?

F R YESS · 11-29-2016, 10:11 PM

300 doesn't seem too bad from the dealer..

The 86 still comes with the plastic one?!

Sent from my iPhone using Tapatalk

MintyTS · 11-30-2016, 08:58 AM

Quote:

Originally Posted by F R YESS

300 doesn't seem too bad from the dealer..

That's a really surprising dealer price, since I was quoted almost that same amount for a single OEM tail light. I don't want to spend the cash on this and a tune until I'm able to get my headers, but if I ever see that plastic start falling apart I'll be all over this thing.

scottman · 12-09-2016, 10:29 AM

I wanna snaz' up my engine bay a little and grab one of these. Was just quoted $407.00 CAD for the part from the local dealership.
But... Would it mess with my tune..?
Are the runner lengths the same and such?
Would it be safe?

Gearbanger · 12-09-2016, 10:31 AM

I just want to verify its a direct swap. Moto East has done this already.

Thoughts? Inquiring minds want to know!

-Phil · 12-09-2016, 10:41 AM

Quote:

Originally Posted by Gearbanger

I just want to verify its a direct swap. Moto East has done this already.

Thoughts? Inquiring minds want to know!

Everything Bolts up except the Map Sensor which is a 10/32 thread pitch bolt now, then you have the Fuel rail covers which need to be drilled or removed.

Gearbanger · 12-09-2016, 11:22 AM

Quote:

Originally Posted by Moto-Phil

Everything Bolts up except the Map Sensor which is a 10/32 thread pitch bolt now, then you have the Fuel rail covers which need to be drilled or removed.

Thanks for the insight! My next mod.

zeal86 · 07-23-2017, 12:17 AM

I have recently installed this manifold and it is really great looking! One thing that bothered me was the lack of a cover.

Recently I have started fabricating my own... I am almost to the point of fabbing my final product. My final will have two cut out and color backed text logos.

Anyway, here are some pics of my process...

I decided to do things differently here... instead of having the little extensions that meet up with the sides... I'm going to cut that shape last and rivet it to the rear bracket.

2nd Aluminum Prototype...

Btw, the bolt that holds the manifold is an M5 .8tp x 15mm

Also, I will finish my two prototypes... I may have them painted or powder coated... So I will have two extra that I will sell if anyone is interested.

__________________________________________

projekt zeal86 build

zeal.eightsix Facebook

Instagram @zeal.eightsix

10-25-2016, 10:54 AM	#15
Gearbanger Senior Member Join Date: Dec 2009 Drives: Lexus is300 celica gts Location: Pittsburgh Posts: 202 Thanks: 1 Thanked 62 Times in 20 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	Bump for update on these. Thanks __________________

10-25-2016, 06:31 PM	#16
GsxrMe Senior Member Join Date: Jul 2015 Drives: Late 2014 Subaru BRZ Location: Cape Coral, FL Posts: 557 Thanks: 20 Thanked 183 Times in 139 Posts Mentioned: 5 Post(s) Tagged: 2 Thread(s)	Sorry, I added to your thread. The intake looks sexy as hell but i'm going to wait for the install and do the block, and return style fuel system at the same time. Kinda want to do it the right way and save myself the trouble of dumping money into retunes and possible small issues to do nothing more than to change it again in a few months. Work has been busy and the $$$ bonuses have been high. I got plenty of cash to dump into the BRZ as a project car. I finally finished my 1997 Wrangler and shes my daily as I pull the motor and take my time on the BURZ! This thread won't be updated anytime soon, Figure 3 months of my engine sitting in my den on a engine stand. __________________ 2014 Subaru BRZ FBM Turbokit: GTX3076R - ECUTEK HRI FlexFuel tune - FBM 3" Turboback Exhaust - 550cc Injectors - Walbro 485 Fuel Pump - 4bar Map Sensor - FBM Oil Pan - ACT SB7-XTSS - AMSOIL all fluids - Forester XT Oil Cooler - Cusco engine, trans mounts - Whiteline rear differential bushings - Perrin shifter bushing - Firehawk 235/45/17 - AEM Failsafe

10-29-2016, 06:08 PM	#17
mrk1 Senior Member Join Date: Mar 2013 Drives: Sterling BRZ Ltd Location: New England Posts: 1,702 Thanks: 403 Thanked 1,389 Times in 671 Posts Mentioned: 20 Post(s) Tagged: 2 Thread(s)	Anyone have a part # for this? __________________ The Build Thread GT28RS - eBoost2 - 3.91 Final Drive - Supra LSD

11-02-2016, 08:16 PM	#20
GsxrMe Senior Member Join Date: Jul 2015 Drives: Late 2014 Subaru BRZ Location: Cape Coral, FL Posts: 557 Thanks: 20 Thanked 183 Times in 139 Posts Mentioned: 5 Post(s) Tagged: 2 Thread(s)	Ft86speedfactory.com has a very aggressive price, subi parts website is below http://parts.subaru.com/p/MANIFOLD-C...4001AC540.html __________________ 2014 Subaru BRZ FBM Turbokit: GTX3076R - ECUTEK HRI FlexFuel tune - FBM 3" Turboback Exhaust - 550cc Injectors - Walbro 485 Fuel Pump - 4bar Map Sensor - FBM Oil Pan - ACT SB7-XTSS - AMSOIL all fluids - Forester XT Oil Cooler - Cusco engine, trans mounts - Whiteline rear differential bushings - Perrin shifter bushing - Firehawk 235/45/17 - AEM Failsafe

11-29-2016, 09:54 PM	#21
Gearbanger Senior Member Join Date: Dec 2009 Drives: Lexus is300 celica gts Location: Pittsburgh Posts: 202 Thanks: 1 Thanked 62 Times in 20 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	So who's installed this already. Lol easy swap? __________________

11-29-2016, 10:11 PM	#22
F R YESS Member Join Date: May 2016 Drives: 2015 Firestorm FR-S Location: Modesto, California Posts: 52 Thanks: 26 Thanked 18 Times in 14 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	300 doesn't seem too bad from the dealer.. The 86 still comes with the plastic one?! Sent from my iPhone using Tapatalk __________________ Not trying to make it perfect; I'm just trying to make it. 2015 Scion FR-S 6MT 2016 Subaru Crosstrek CVT 1972 Chevy C10 Shortbed 2018 Honda Civic Si Sedan

12-09-2016, 10:29 AM	#24
scottman Member Join Date: Jun 2012 Drives: 13 mt fr-s Location: Halton Hills, Ont. Posts: 171 Thanks: 73 Thanked 96 Times in 48 Posts Mentioned: 0 Post(s) Tagged: 1 Thread(s)	I wanna snaz' up my engine bay a little and grab one of these. Was just quoted $407.00 CAD for the part from the local dealership. But... Would it mess with my tune..? Are the runner lengths the same and such? Would it be safe?

12-09-2016, 10:31 AM	#25
Gearbanger Senior Member Join Date: Dec 2009 Drives: Lexus is300 celica gts Location: Pittsburgh Posts: 202 Thanks: 1 Thanked 62 Times in 20 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	I just want to verify its a direct swap. Moto East has done this already. Thoughts? Inquiring minds want to know! __________________

07-23-2017, 12:17 AM	#28
zeal86 Senior Member Join Date: Jul 2014 Drives: Posts: 1,947 Thanks: 1,149 Thanked 1,773 Times in 872 Posts Mentioned: 23 Post(s) Tagged: 0 Thread(s)	I have recently installed this manifold and it is really great looking! One thing that bothered me was the lack of a cover. Recently I have started fabricating my own... I am almost to the point of fabbing my final product. My final will have two cut out and color backed text logos. Anyway, here are some pics of my process... I decided to do things differently here... instead of having the little extensions that meet up with the sides... I'm going to cut that shape last and rivet it to the rear bracket. 2nd Aluminum Prototype... Btw, the bolt that holds the manifold is an M5 .8tp x 15mm Also, I will finish my two prototypes... I may have them painted or powder coated... So I will have two extra that I will sell if anyone is interested. __________________________________________ projekt zeal86 build zeal.eightsix Facebook Instagram @zeal.eightsix

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New Carbing Aluminum Air Intake Suction Kit	Pekingduck	Engine, Exhaust, Bolt-Ons	11	11-28-2016 07:16 PM
FS: Lower control arm	ssyed	Canada Classifieds	24	10-30-2016 06:13 PM
PRICE DROP New Fujitsubo Authorize-R Catback Exhaust & Carbing Aluminum Air Intake	Pekingduck	Engine, Exhaust, Bolt-Ons	7	07-15-2016 06:30 PM
?? about the 2017 changes.	UAmach1	Scion FR-S / Toyota 86 GT86 General Forum	26	03-28-2016 08:55 PM
GenomeTuning Aluminum Intake Plugs	genometuning	Engine, Exhaust, Bolt-Ons	58	06-23-2014 07:43 PM

User Name		Remember Me?
Password