2017 BRZ front bumper conversion 2014MY

[RavioliG]

Originally Posted by TOLM

I have a 2017 brz and i like the pre 2017 front bumpers way better ((

TRADE ME THEN

[tweedbean]

Is there a gap around the headlights when doing this swap? Or is it a perfect fit?

[TheBRZsKnees]

So if you go with the 2017 fog lights, can this be done without any cutting or modification? Curious if I could do the swap in my apartment carport with minimal tools lol.

Shout out to OP for the walkthrough, and for recommending a good place for paint in the PNW.

Edit: Those stock fog lights aint cheap! The Winjet ones seem like a good alternative though.

[malubawla]

you can reuse your factory fogs in the 2017 bumper swap. just need to attach with one bolt and one ziptie

[TheBRZsKnees]

Originally Posted by malubawla

you can reuse your factory fogs in the 2017 bumper swap. just need to attach with one bolt and one ziptie

After taking a closer look at this thread, it looks like people are using the pre-facelift DRLs, not the fog lights

But it looks like you did the swap and were actually able to fit your pre-facelift fogs?

[malubawla]

Originally Posted by tweedbean

Is there a gap around the headlights when doing this swap? Or is it a perfect fit?

no gap as long as you use the headlight bracket from the 2017

[malubawla]

Originally Posted by ph4zon

After taking a closer look at this thread, it looks like people are using the pre-facelift DRLs, not the fog lights

But it looks like you did the swap and were actually able to fit your pre-facelift fogs?

sure was, held with one bolt and one ziptie, rotated slightly. even has my 2013 front lip on

[Byeezus10]

Originally Posted by malubawla

sure was, held with one bolt and one ziptie, rotated slightly. even has my 2013 front lip on

Car looks amazing man! Do you know if the swap would work with a 2015 FRS? Not sure how different bolts and how lights were setup. Thanks!

[malubawla]

pmed..

[B T]

Originally Posted by malubawla

no gap as long as you use the headlight bracket from the 2017

So using the 2015 brackets isn't going to work? Thought I saw they had the same part number.

57707CA181
57707CA191

[ChicagoNole]

I just did the 2017 bumper on my 2014 FRS and its not fitting too well in the corners.

I bought the bumper bracket set, part #s 57707CA040 57707CA050 , but...and maybe I didn't look too closely, they seemed to be the same ones already on my car so I returned them.

In the post you have these 2 parts:
57707CA180
57707CA190
Are these the parts that run under the headlight area? When I go to buy them online, all of the websites say there is a new part available: 57707CA181 and 57707CA191.. does anyone know if those will work or do I need to find the old ones?

[blown]

anyone know if the olm drl works with the oem plugs for 13 brz drl?

http://www.ft86speedfactory.com/olm-...l#.XMFhMOhKiHt

[bobmcboberston]

Originally Posted by blown

anyone know if the olm drl works with the oem plugs for 13 brz drl?

http://www.ft86speedfactory.com/olm-...l#.XMFhMOhKiHt

It does not, it comes with an add a fuse and both wires are already connected.

[Irace86.2.0]

Originally Posted by bobmcboberston

It does not, it comes with an add a fuse and both wires are already connected.

Already connected to a plug that doesn’t match the 13 drls?

Is it a simple two wire in and out? I am curious if the Drls can be wired up the same even if the plugs don’t match and if they work with the DD Always On system.