07-30-2012, 11:42 PM | #127 | |
Senior Member
Join Date: Apr 2012
Drives: '14 Monogram FR-S(RIP)
Location: Long Beach, CA
Posts: 909
Thanks: 258
Thanked 417 Times in 202 Posts
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
|
Quote:
|
|
07-30-2012, 11:43 PM | #128 |
Senior Member
Join Date: Apr 2012
Drives: '14 Monogram FR-S(RIP)
Location: Long Beach, CA
Posts: 909
Thanks: 258
Thanked 417 Times in 202 Posts
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
|
|
07-30-2012, 11:49 PM | #129 | |
give us this day
Join Date: Jul 2012
Drives: AE86 - FRS
Location: Three Stars & A Sun
Posts: 404
Thanks: 138
Thanked 161 Times in 37 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Quote:
So try to just peel off from the side of the letters?
__________________
|
|
07-30-2012, 11:54 PM | #130 |
Senior Member
Join Date: Apr 2012
Drives: '14 Monogram FR-S(RIP)
Location: Long Beach, CA
Posts: 909
Thanks: 258
Thanked 417 Times in 202 Posts
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
|
|
The Following User Says Thank You to Trojan_SC For This Useful Post: | imravenit (07-31-2012) |
07-31-2012, 12:01 AM | #131 |
Member
Join Date: Jul 2012
Drives: 2013 BRZ
Location: Kansas
Posts: 33
Thanks: 0
Thanked 3 Times in 3 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
I know this is an FR-S Debadging Tutorial, But could someone tell me if the toyota logo would fit over the subaru logo? everywhere i look its a scion debadging just curious if its possible for the brz
|
07-31-2012, 12:03 AM | #132 |
Senior Member
Join Date: Apr 2012
Drives: '14 Monogram FR-S(RIP)
Location: Long Beach, CA
Posts: 909
Thanks: 258
Thanked 417 Times in 202 Posts
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
|
Pretty sure it can be done considering both cars are practically identical.
|
07-31-2012, 12:16 AM | #133 |
Senior Member
Join Date: Apr 2012
Drives: '14 Monogram FR-S(RIP)
Location: Long Beach, CA
Posts: 909
Thanks: 258
Thanked 417 Times in 202 Posts
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
|
|
07-31-2012, 12:47 AM | #134 |
Senior Member
Join Date: Jul 2012
Drives: 2023 WRB BRZ (MT)
Location: Coral Springs, SoFlo
Posts: 2,252
Thanks: 1,503
Thanked 534 Times in 430 Posts
Mentioned: 42 Post(s)
Tagged: 5 Thread(s)
|
|
07-31-2012, 12:54 AM | #135 |
Senior Member
Join Date: Apr 2012
Drives: '14 Monogram FR-S(RIP)
Location: Long Beach, CA
Posts: 909
Thanks: 258
Thanked 417 Times in 202 Posts
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
|
|
07-31-2012, 12:56 AM | #136 | |
give us this day
Join Date: Jul 2012
Drives: AE86 - FRS
Location: Three Stars & A Sun
Posts: 404
Thanks: 138
Thanked 161 Times in 37 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Haha took me awhile to find the edge i was too focus on the edges of the lettering.. stood back a bit since im getting frustrated.. N blah saw a slight shadow of line at the very edge of the whole thing just below the right or left corner of the trunk door.. Thanks man! Finally done!
__________________
|
|
07-31-2012, 12:58 AM | #137 | |
Senior Member
Join Date: Apr 2012
Drives: '14 Monogram FR-S(RIP)
Location: Long Beach, CA
Posts: 909
Thanks: 258
Thanked 417 Times in 202 Posts
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
|
Quote:
|
|
The Following User Says Thank You to Trojan_SC For This Useful Post: | imravenit (07-31-2012) |
07-31-2012, 01:28 AM | #138 |
give us this day
Join Date: Jul 2012
Drives: AE86 - FRS
Location: Three Stars & A Sun
Posts: 404
Thanks: 138
Thanked 161 Times in 37 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
So i followed the flossing technique... I did not use a blow dryer.. I was afraid if i heat it up a bit i might chip the paint specially in the front badge..
Tools used: 1. Applied goo gone around badges.. 2. Flossed badges in a sawing motion while pulling towards me 3. Quick waxed after all goos are gone! (notice the reflection and tell me what you see!)
__________________
|
08-02-2012, 09:46 AM | #139 |
Self Entitled
Join Date: Jul 2012
Drives: 13' Red FR-S, 12' Toyota Tundra
Location: Dallas, TX
Posts: 122
Thanks: 17
Thanked 13 Times in 13 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Debadged the FRS and the Tundra yesterday.. my fingers are sore from rolling up all that adhesive haha.
Method that worked for me was: -Heat up the emblem slightly with a heat gun or hair dryer -use some fishing line (and gloves) and using a saw motion back and forth, cut the adhesive behind the emblem. -Use your fingers to roll/peel the left over glue -Use some Goo-Gone to remove any left over glue -Use some spay polish to make the area nice and clean Now I just have to order some Toyota emblems.. |
08-02-2012, 09:51 AM | #140 |
Self Entitled
Join Date: Jul 2012
Drives: 13' Red FR-S, 12' Toyota Tundra
Location: Dallas, TX
Posts: 122
Thanks: 17
Thanked 13 Times in 13 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Anyone know where to get these emblems?
I looked for Carson Toyota on the search but his threads show up as inactive.. maybe he got banned? |
|
|
Tags |
teq emblem |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Debadging - How difficult will it be? | Dadhawk | Scion FR-S / Toyota 86 GT86 General Forum | 86 | 06-24-2014 10:49 PM |