Jackson Racing Supercharger Owners Thread - Page 46 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

bacon_cheese_beer · 06-28-2014, 09:22 PM

washed my baby today!

Ethan · 07-01-2014, 09:58 PM

Quote:

Originally Posted by Ralph Spoilsport

I keep hoping that someone will figure out how to get this right reliably and publish a DIY. Or maybe I'll get to be that guy.

Any luck with the bumper separation issue? I have the same problem. Tried new clips and that didn't help.

CSG David · 07-02-2014, 12:52 AM

Quote:

Originally Posted by Ethan

Any luck with the bumper separation issue? I have the same problem. Tried new clips and that didn't help.

Typical bumper issue if you're not too careful during removal. It's kind of annoying, but if you got the finesse down, it goes back in perfectly. In terms of the intake piping, just remember to massage it to fit properly. Everything was sized so your pipes don't randomly pop out if you didn't tighten down the clamps enough.

Suddenly... · 07-02-2014, 09:13 AM

Quote:

Originally Posted by bacon_cheese_beer

washed my baby today!

I love how this car looks. Any chance I can ask one of the photoshop gurus to try and shop it to look like firestorm? I would love to see how my car would look with this setup. Beautiful man, and so clean too

2ndgenhachi · 07-02-2014, 04:19 PM

Can anybody clarify if there is a way to get the ecutek features like launch control, ffs, rev matching etc onthecarb tune for the Jr kit? I've been trying to research this but haven't found a concrete answer.

CSG David · 07-03-2014, 02:09 PM

Quote:

Originally Posted by 2ndgenhachi

Can anybody clarify if there is a way to get the ecutek features like launch control, ffs, rev matching etc onthecarb tune for the Jr kit? I've been trying to research this but haven't found a concrete answer.

The latest EcuTek software revision contains those modules/parameters. The CARB tune was developed prior to that EcuTek software update so it does not have that programmed in. That doesn't mean you can't dial that parameter yourself...

*LongFella · 07-03-2014, 03:55 PM

Anybody with the JR Oil Cooler kit notice oil residue building up around the extension piece (right below where the two lines come out)? Is that normal? It doesn't look like it is leaking... but it is certainly not clean...

I was away for a few weeks (got married and honeymoon) and when I started the car... did the walk around and engine check... I noticed it for the first time...

Don't have a picture yet... but can post one later if needed...

*LongFella · 07-05-2014, 01:59 PM

Not the best photos, but is anybody else getting some oil build up here with the oil cooler kit?

I'm doing an oil change now, so I'll tighten the extension bolt a little more...
Name: ImageUploadedByTapatalk1404583150.186398.jpg
Views: 1878
Size: 207.1 KB

Name: ImageUploadedByTapatalk1404583150.186398.jpg
Views: 1878
Size: 207.1 KB

Name: ImageUploadedByTapatalk1404583158.402640.jpg
Views: 1874
Size: 235.9 KB

*LongFella · 07-05-2014, 05:42 PM

Just finished an oil change and checked the kit for any issues... Absolutely nothing wrong or any wear on any part!

I've got just over 10k miles with over half of them with this kit and oil cooler...and not one issue. Awesome! We made the right choice going with this kit!

Avo1789 · 07-05-2014, 11:20 PM

Quote:

Originally Posted by CSG David

Any time you plan on changing the factory catalytic converters, a tune will be required. Catback exhausts and aftermarket overpipes will work with the CARB tune, but any modification to those OEM factory catalytic converters will pose a little problem.

What if the only exhaust change is catted headers(such as FT86SF uel). Would it need a custom tune?

CSG David · 07-06-2014, 05:24 AM

Quote:

Originally Posted by Avo1789

What if the only exhaust change is catted headers(such as FT86SF uel). Would it need a custom tune?

Yes. High flow catalytic converter is not an OEM catalytic converter. You are changing the factory OEM emissions components and therefore the flow characteristics will change.

*LongFella · 07-06-2014, 06:52 PM

Any thoughts on my oil cooler seepage issue?

enivid · 07-07-2014, 12:02 AM

Quote:

Originally Posted by *LongFella

Any thoughts on my oil cooler seepage issue?

Mine had a slight leak from down there and from the tubing connections. I took it all apart when I did my oil change a month ago and so far everything is clean now.

CSG Mike · 07-07-2014, 12:38 AM

Quote:

Originally Posted by *LongFella

Any thoughts on my oil cooler seepage issue?

Just make sure everything is tightened to spec, and you shouldn't see any seepage. It's a bit awkward to tighten without the proper tools.

06-28-2014, 09:22 PM	#631
bacon_cheese_beer Senior Member Join Date: Aug 2012 Drives: Fr-S Location: Everett, WA Posts: 141 Thanks: 124 Thanked 128 Times in 43 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	washed my baby today! __________________ "mr.Balloon hands, no way, get real..."

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Jackson Racing Rotrex Supercharger System Info and Discussion	Jackson Racing	Forced Induction	827	04-06-2020 04:56 PM
Jackson Racing Supercharger Press Release and Info	CounterSpace Garage	Forced Induction	110	01-03-2017 09:04 PM
jackson Racing engine oil cooler - modular to fit the Jackson Racing Supercharger!	CSG Mike	Forced Induction	24	04-27-2016 12:59 PM
Jackson Racing supercharger	NoppyNop	Forced Induction	241	06-26-2014 03:05 PM
Jackson Racing Supercharger Pre-Order Sale, $200 off!	Xero-Limit	Forced Induction	2	03-05-2014 04:14 PM

07-02-2014, 04:19 PM	#635
2ndgenhachi Member Join Date: Feb 2014 Drives: 2013 fr-s, sr20 180sx Location: Birmingham Posts: 71 Thanks: 4 Thanked 15 Times in 14 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Can anybody clarify if there is a way to get the ecutek features like launch control, ffs, rev matching etc onthecarb tune for the Jr kit? I've been trying to research this but haven't found a concrete answer.

User Name		Remember Me?
Password