SINGLE EXIT EXHAUST

[AznKirby]

T1R

[NickDC88]

Originally Posted by Kevinmp7

I'm running a Tomei type 80
What spoiler are you using, it is exactly what I'm looking for!



My type 80 sits a little low also but I think that is how its suppose to be. I know I scraped it a couple times when I did a run through the canyons lol.

Abflug replica. Got it from modbargains.com

Originally Posted by TrogDor the Burninator

I've got the 60S, too ...

Looks like your ride height is a little lower than mine, but I can see that the pipe leading to the muffler is a bit low. After I installed the Tomei 60S, I had to loosen all the fittings and then work to get it sung and as high as possible to the rear axle. Lots of twisting the pipe fittings to get the maximum height on the piping.

I noticed it looked a little low but it sits in line with the wheels so I figured it shouldn't be too much of a problem.

[ichitaka05]

Originally Posted by phobos512

Berk single exit delete with a 4" tip from corner3garage.com. Innovative Dynamics carbon fiber delete cover on the passenger side.

How loud is it? Cuz isn't it no muffler?

[Kevinmp7]

Here is the Tomei Type 80


The pipe sits around 2.5 inches off the ground with the Tein S. tech springs installed (around 1 inch drop).

[mike the snake]

I have the same exhaust. Originally, mine was mounted like yours, but with some twisting and tweaking, I got the pipe up to where it almost touches the crossmember, gaining another 1.5'' of ground clearance.

My car is lowered 1.5'' and the pipe does not scrape anywhere (so far).

I LOVE my 80R exhaust by the way.

Originally Posted by Kevinmp7

Here is the Tomei Type 80


The pipe sits around 2.5 inches off the ground with the Tein S. tech springs installed (around 1 inch drop).

[Kevinmp7]

Originally Posted by mike the snake

I have the same exhaust. Originally, mine was mounted like yours, but with some twisting and tweaking, I got the pipe up to where it almost touches the crossmember, gaining another 1.5'' of ground clearance.

My car is lowered 1.5'' and the pipe does not scrape anywhere (so far).

I LOVE my 80R exhaust by the way.

I haven't scraped yet but I'll see if I can tweak it this weekend. Thanks for the info

[ichitaka05]

Anyone here have these single exit exhausts & have any pics & vids?
Blitz Nur Spec R
ARK Design Racing Spec
EVS Tuning SSP
Fujitsubo Authorize RM
Kakimoto Racing GT1.0
Tanabe Medalion Concept G
Ultimate Racing 3" single exit

[TrogDor the Burninator]

Here's a few vids of a Tomei 60S with stock header, overpipe, and frontpipe, without the silencer, and with ...

And the second set are are the same Tomei 60s but with the FT-86 SpeedFactory Catted UEL, with stock overpipe and frontpipe ...



Stock header, overpipe, frontpipe and Tomei 60S:
[ame="https://www.youtube.com/watch?v=DnDrO32UzfU"]Tomei Expreme Ti 60S Catback on 2013 Scion FR-S - YouTube[/ame]



Stock header, overpipe, frontpipe and Tomei 60S with silencer:
[ame="https://www.youtube.com/watch?v=PB4MeN4HSy4"]Tomei Expreme Ti 60S Catback with Silencer - YouTube[/ame]



FT-86 SpeedFactory Catted UEL Header, stock overpipe and frontpipe, and Tomei 60S without silencer:
[ame="https://www.youtube.com/watch?v=CLk08OC89aw"]FT-86 SpeedFactory Catted UEL Header Testing - YouTube[/ame]



FT-86 SpeedFactory Catted UEL Header, stock overpipe and frontpipe, and Tomei 60S without silencer:
[ame="https://www.youtube.com/watch?v=d6Goc9EVwJY"]FT86 SpeedFactory Catted UEL Header Testing Cold Start to Stationary Revs - YouTube[/ame]



Enjoy!

[ichitaka05]

Originally Posted by TrogDor the Burninator

Here's a few vids of a Tomei 60S with stock header, overpipe, and frontpipe, without the silencer, and with ...

And the second set are are the same Tomei 60s but with the FT-86 SpeedFactory Catted UEL, with stock overpipe and frontpipe ...



Stock header, overpipe, frontpipe and Tomei 60S:

Stock header, overpipe, frontpipe and Tomei 60S with silencer:

FT-86 SpeedFactory Catted UEL Header, stock overpipe and frontpipe, and Tomei 60S without silencer:

FT-86 SpeedFactory Catted UEL Header, stock overpipe and frontpipe, and Tomei 60S without silencer:

Enjoy!

Thanks!

Full setup make pretty mean sound! How the sound inside the cabin? is it loud?

[phobos512]

Originally Posted by ichitaka05

How loud is it? Cuz isn't it no muffler?

I dunno...not as loud as my motorcycle with a stock muffler but the butterfly valve removed. I rather like the sound compared to stock which for me was essentially silent. It drones a bit around 2500 RPM but it's plenty manageable. It's also not as loud as my totally stock 13 Ram 2500 diesel was.

It totally removes the stock muffler so it's just the cats doing the work of reducing sound output.

[TrogDor the Burninator]

Originally Posted by ichitaka05

Thanks!

Full setup make pretty mean sound! How the sound inside the cabin? is it loud?

I made a new video of the in-cabin sound experience and some commentary on the FT-86 SpeedFactory header ... The video is currently processing, so once it is done and I load it up to YouTube I will put the link in here.

I really like the combination of this header and the Tomei 60S ... It's loud outside, but not completely ridiculous ... and inside the cabin the header makes it quite good actually ...

Seems like the best of both worlds ....

[ichitaka05]

Originally Posted by phobos512

I dunno...not as loud as my motorcycle with a stock muffler but the butterfly valve removed. I rather like the sound compared to stock which for me was essentially silent. It drones a bit around 2500 RPM but it's plenty manageable. It's also not as loud as my totally stock 13 Ram 2500 diesel was.

It totally removes the stock muffler so it's just the cats doing the work of reducing sound output.

I rarely see Ram 2500 diesel around here, but I kinda get the idea what you're trying to say

Originally Posted by TrogDor the Burninator

I made a new video of the in-cabin sound experience and some commentary on the FT-86 SpeedFactory header ... The video is currently processing, so once it is done and I load it up to YouTube I will put the link in here.

I really like the combination of this header and the Tomei 60S ... It's loud outside, but not completely ridiculous ... and inside the cabin the header makes it quite good actually ...

Seems like the best of both worlds ....

Nice! Can't wait to hear it

[TrogDor the Burninator]

Originally Posted by ichitaka05

Thanks!

Full setup make pretty mean sound! How the sound inside the cabin? is it loud?

Alright ... here's the link to the video of the in-cabin sound of the FT-86 SpeedFactory Catted UEL Header paired with my Tomei 60S ...

The video is still uploading at this moment ... 82% so should be up in about 15 minutes ... or about 6 central time.

[ame="https://www.youtube.com/watch?v=m-bEAUm3dAs"]FT-86 SpeedFactory Catted UEL Header - In cabin Sound Experience and Commentary - YouTube[/ame]

[akahenry]

Originally Posted by TrogDor the Burninator

Alright ... here's the link to the video of the in-cabin sound of the FT-86 SpeedFactory Catted UEL Header paired with my Tomei 60S ...

The video is still uploading at this moment ... 82% so should be up in about 15 minutes ... or about 6 central time.

Video appears to be "Private"