Scangauge oil temp xgauge code [Working] - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

pkny · 02-06-2013, 10:38 PM

Working code for FR-S/BRZ/86:

Code:

Gauge                          Unit           TXD                  RXF                      RXD      MTH                      Note
Oil temp                       C         07E02101       010702E80324     3008    00010001FFD8    Required FW 4.05 or higher
Oil temp                       F         07E02101       010702E80324     3008    00090005FFD8    Required FW 4.05 or higher
 
Precise Fuel Level         %         07C02129       046105290000     2808    000100010000    Faster refresh rate
Precise Fuel Level    US Gallons   07C02129       046145290000     2808    052900640000    Faster refresh rate
Precise Fuel Level       Liters      07C02129        046145290000     2808    01F4000A0000    Faster refresh rate
 
Seat Belt Beep Query               07C021A7        046115A70000     2808    000100010000   C0 for stock, 00 for disable
Seat Belt Beep Disable              07C03BA700    047B15A70000     2008    000100010000   Should return 0000. Replace '00' in the TXD with 'C0' to go back to stock.
 
Relative Throttle Position      %           07E00145            044185450000         2808     03E800FF0000     
Absolute Throttle Position     %           07E00147            044185470000         2808     03E800FF0000
 
Fuel Pressure                     PSI         07E00123            046105230000         2810     006400450000 
Fuel Pressure                    MPa         07E00123            046145230000         2810     000100010000

86 Standard PIDs.doc is the list of supported standard (mode 01) PID for 86/BRZ/FR-S. This list is created from the Wiki’PID, and I highlighted the ones that are supported by our cars.

Here is an example of how to make use of the doc I created:
From the Xgauge cansf list, the short Term Fuel Trim Bank 1 has the TXD 07E00106. The 01 (07E00106) is the mode #. The 06 (07E00106) is the PID. Now look at the doc I attached. It shows the PID 06 is supported, which means that xgauge code works on our cars. The PID 07, On the other hand, is not highlighted on the list. That means the Short Term Fuel Trim Bank 2 is not supported.

Thank you Andery for finding the PID and torque’s code for oil temperature. Without him, I don’t think I can get the oil temp for xgauge.

jonnyboy · 02-06-2013, 10:49 PM

You are amazing!
Thanks for figuring this out!

jonnyboy · 02-07-2013, 02:26 AM

Not sure if my the codes would vary by locality, but on my scangauge I had to alter one value in the MTH:
MTH 00010001FFD8

pkny · 02-07-2013, 02:45 AM

Jonnyboy, thank you for catching my typo. Yeah, it should be 00010001FFD8. It has been a long day. Anyway, the 1st post was corrected.

86•BRZ · 02-07-2013, 05:03 AM

worked for me... a million thanks!

Nardi330 · 02-07-2013, 06:22 AM

Sorry for bring a noob. Can you also post the steps to setup in the scangauge?

Thanks in advance.

Edit: never mind, found some instruction online and Weill try it later.

Synack · 02-07-2013, 10:34 PM

Quote:

Originally Posted by 86•BRZ

worked for me... a million thanks!

The IA is intake air temp?

What's WT, water?

R2 · 02-07-2013, 10:43 PM

I've had my eye on the ScanGuage for quite awhile, this is great. By the way, will the Scanguage fit in the slot under the a/c controls? It looks close, maybe not for the push button start equipped cars but perhaps the ones without.

TIE Pilot · 02-07-2013, 10:51 PM

Quote:

Originally Posted by R2

I've had my eye on the ScanGuage for quite awhile, this is great. By the way, will the Scanguage fit in the slot under the a/c controls? It looks close, maybe not for the push button start equipped cars but perhaps the ones without.

http://www.scangauge.com/image-resou..._with-dims.jpg

Sent from my iPhone using Tapatalk

R2 · 02-07-2013, 11:07 PM

Quote:

Originally Posted by mr_m

http://www.scangauge.com/image-resou..._with-dims.jpg

Sent from my iPhone using Tapatalk

Boom. There it is, thanks.

TIE Pilot · 02-07-2013, 11:09 PM

You can set the The ScanGaugeE the same right? Since is more than an 1" shorter should fit b/w start button and usb

Sent from my iPhone using Tapatalk

R2 · 02-07-2013, 11:24 PM

Quote:

Originally Posted by mr_m

You can set the The ScanGaugeE the same right? Since is more than an 1" shorter should fit b/w start button and usb

Sent from my iPhone using Tapatalk

So I couldn't find my tape measure but with a shitty ruler I found that there is plenty of width for the standard unit. However, height is an issue and you may have to remove or trim the rubber in the slot. The height of the slot without that rubber is over 1.5" though so it can work. My other concern is the display contrast - can you see the display clearly from the drivers position if it were installed there flush with the dash?

86•BRZ · 02-08-2013, 02:03 AM

Quote:

Originally Posted by Synack

The IA is intake air temp?

What's WT, water?

yep, exactly right

86•BRZ · 02-08-2013, 02:07 AM

here is a pic I found on these forums somewhere

Ill have to look into the scangauge E, hopefully it will fit in the start button models. I pinched this scangage from my other car anyway..

02-06-2013, 10:38 PM	#1
pkny Senior Member Join Date: Feb 2012 Drives: Firestorm FR-S 6MT Location: SF Bay area Posts: 103 Thanks: 12 Thanked 91 Times in 27 Posts Mentioned: 2 Post(s) Tagged: 1 Thread(s)	Scangauge xgauge code for oil temp, seat belt beep disable, and more Working code for FR-S/BRZ/86: Code: Gauge Unit TXD RXF RXD MTH Note Oil temp C 07E02101 010702E80324 3008 00010001FFD8 Required FW 4.05 or higher Oil temp F 07E02101 010702E80324 3008 00090005FFD8 Required FW 4.05 or higher Precise Fuel Level % 07C02129 046105290000 2808 000100010000 Faster refresh rate Precise Fuel Level US Gallons 07C02129 046145290000 2808 052900640000 Faster refresh rate Precise Fuel Level Liters 07C02129 046145290000 2808 01F4000A0000 Faster refresh rate Seat Belt Beep Query 07C021A7 046115A70000 2808 000100010000 C0 for stock, 00 for disable Seat Belt Beep Disable 07C03BA700 047B15A70000 2008 000100010000 Should return 0000. Replace '00' in the TXD with 'C0' to go back to stock. Relative Throttle Position % 07E00145 044185450000 2808 03E800FF0000 Absolute Throttle Position % 07E00147 044185470000 2808 03E800FF0000 Fuel Pressure PSI 07E00123 046105230000 2810 006400450000 Fuel Pressure MPa 07E00123 046145230000 2810 000100010000 86 Standard PIDs.doc is the list of supported standard (mode 01) PID for 86/BRZ/FR-S. This list is created from the Wiki’PID, and I highlighted the ones that are supported by our cars. Here is an example of how to make use of the doc I created: From the Xgauge cansf list, the short Term Fuel Trim Bank 1 has the TXD 07E00106. The 01 (07E00106) is the mode #. The 06 (07E00106) is the PID. Now look at the doc I attached. It shows the PID 06 is supported, which means that xgauge code works on our cars. The PID 07, On the other hand, is not highlighted on the list. That means the Short Term Fuel Trim Bank 2 is not supported. Thank you Andery for finding the PID and torque’s code for oil temperature. Without him, I don’t think I can get the oil temp for xgauge. __________________ 2013 Scion Firestorm FR-S MT Last edited by pkny; 06-11-2013 at 09:12 PM. Reason: Updated the code

02-07-2013, 02:45 AM	#4
pkny Senior Member Join Date: Feb 2012 Drives: Firestorm FR-S 6MT Location: SF Bay area Posts: 103 Thanks: 12 Thanked 91 Times in 27 Posts Mentioned: 2 Post(s) Tagged: 1 Thread(s)	Jonnyboy, thank you for catching my typo. Yeah, it should be 00010001FFD8. It has been a long day. Anyway, the 1st post was corrected. __________________ 2013 Scion Firestorm FR-S MT Last edited by pkny; 02-07-2013 at 03:07 AM.

02-07-2013, 05:03 AM	#5
86•BRZ Senior Member Join Date: Nov 2012 Drives: 86 GTS Location: brisbane Posts: 270 Thanks: 46 Thanked 102 Times in 65 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	worked for me... a million thanks! Attached Images

02-07-2013, 06:22 AM	#6
Nardi330 Senior Member Join Date: Sep 2011 Drives: 86 Location: Brisbane Australia Posts: 2,168 Thanks: 287 Thanked 374 Times in 264 Posts Mentioned: 9 Post(s) Tagged: 1 Thread(s)	Sorry for bring a noob. Can you also post the steps to setup in the scangauge? Thanks in advance. Edit: never mind, found some instruction online and Weill try it later. Last edited by Nardi330; 02-07-2013 at 07:16 AM.

02-07-2013, 11:09 PM	#11
TIE Pilot Senior Member Join Date: Sep 2012 Drives: TIE interceptor; BRZ13 Location: Miami Posts: 309 Thanks: 131 Thanked 132 Times in 88 Posts Mentioned: 18 Post(s) Tagged: 3 Thread(s)	You can set the The ScanGaugeE the same right? Since is more than an 1" shorter should fit b/w start button and usb Sent from my iPhone using Tapatalk __________________ "Speed has never killed anyone. Suddenly becoming stationary, that's what gets you." Jeremy Clarkson

02-06-2013, 10:49 PM	#2
jonnyboy Member Join Date: Jun 2012 Drives: GTS 86 6AT Location: Sydney, AUstralia Posts: 53 Thanks: 8 Thanked 5 Times in 5 Posts Mentioned: 4 Post(s) Tagged: 0 Thread(s)	You are amazing! Thanks for figuring this out!

02-07-2013, 02:26 AM	#3
jonnyboy Member Join Date: Jun 2012 Drives: GTS 86 6AT Location: Sydney, AUstralia Posts: 53 Thanks: 8 Thanked 5 Times in 5 Posts Mentioned: 4 Post(s) Tagged: 0 Thread(s)	Not sure if my the codes would vary by locality, but on my scangauge I had to alter one value in the MTH: MTH 00010001FFD8

02-07-2013, 10:43 PM	#8
R2 Senior Member Join Date: Nov 2012 Drives: FR-S Location: Sask., Canada Posts: 250 Thanks: 84 Thanked 89 Times in 55 Posts Mentioned: 20 Post(s) Tagged: 1 Thread(s)	I've had my eye on the ScanGuage for quite awhile, this is great. By the way, will the Scanguage fit in the slot under the a/c controls? It looks close, maybe not for the push button start equipped cars but perhaps the ones without.

02-08-2013, 02:07 AM	#14
86•BRZ Senior Member Join Date: Nov 2012 Drives: 86 GTS Location: brisbane Posts: 270 Thanks: 46 Thanked 102 Times in 65 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	here is a pic I found on these forums somewhere Ill have to look into the scangauge E, hopefully it will fit in the start button models. I pinched this scangage from my other car anyway.. Attached Images

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FT-86 low temp THERMOSTAT	ft86-UAE	Engine, Exhaust, Transmission	52	08-30-2016 03:46 PM
A/C Oil/Water temp gauge	Exhaust	Scion FR-S / Toyota 86 GT86 General Forum	16	02-07-2013 01:19 PM
Engine oil temp now available in Torque App	Yruyur	Engine, Exhaust, Transmission	8	02-03-2013 10:52 PM
exterior temp. gauge off?	Rayme	CANADA	8	01-23-2013 09:06 PM
Simple Oil Temp. Gauge	Sportsguy83	Cosmetic Modification (Interior/Exterior/Lighting)	4	01-19-2013 08:25 PM

User Name		Remember Me?
Password