follow ft86club on our blog, twitter or facebook.
FT86CLUB
Ft86Club
RR Racing
Register Garage Members List Calendar Search Today's Posts Mark Forums Read

Go Back   Scion FR-S Forum | Subaru BRZ Forum | Toyota 86 GT 86 Forum | AS1 Forum - FT86CLUB > Technical Topics > Forced Induction

Forced Induction Turbo, Supercharger, Methanol, Nitrous


User Tag List
go_a_way1

Reply
 
Thread Tools Search this Thread
Old 06-05-2018, 10:33 PM   #4579
idkwhatimdoing
Member
 
idkwhatimdoing's Avatar
 
Join Date: Jan 2018
Drives: 2015 Scion FR-S 1968 Camaro BB402
Location: Thousand Oaks, California
Posts: 75
Thanks: 20
Thanked 16 Times in 13 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by stlgrym3 View Post
Whatís ETune? I will get a custom tune from delicious as well when I pair up my C30 with tomei EL.



Do u have a C30 or C38? I was told C38 requires ACE header plus high boost pulleys.


The term youíre looking for is ďrecommendedĒ. Due to the higher volume and velocity of exhaust gasses exiting the cylinder heads itís wise to equip the motor with headers, as well-engineered headers create a sort of suction effect where the exhaust gasses are pulled from the heads.
Your potentials for power gains will skyrocket with a solid aftermarket header, especially with ACE.


________

~refer to username~
idkwhatimdoing is offline   Reply With Quote
Old 06-06-2018, 02:16 AM   #4580
CSG Mike
 
CSG Mike's Avatar
 
Join Date: Jul 2012
Drives: S2000 CR
Location: Orange County
Posts: 11,702
Thanks: 7,215
Thanked 11,122 Times in 5,342 Posts
Mentioned: 824 Post(s)
Tagged: 13 Thread(s)
Quote:
Originally Posted by Anderzz View Post
Etune is just an electronic tune, in other words I didn't physically bring the car to them. I put the tuning software on my own laptop put on the tune, took logs, sent the log results to Delicious and then they sent back the tune after a few rounds of logs.

I have a C38, whoever told you it "requires" anything is just plain wrong. Neither the C30 or C38 require anything, they can both be run on otherwise stock systems, or with any header setup.

Sent from my XT1650 using Tapatalk
He's not posting the full story. What he was told, is that to use a HBP with any JRSC, with CA 91 octane, safely, without massively pulling timing, the Ace header is the only known option.

Any header is fine without HBP.

With HBP, if you want to use ACN91.... well, only one option. If you use high octane or ethanol, then any header will work.
CSG Mike is offline   Reply With Quote
The Following 2 Users Say Thank You to CSG Mike For This Useful Post:
CxG (06-07-2018), mrg666 (06-06-2018)
Old 06-06-2018, 11:49 AM   #4581
stlgrym3
Senior Member
 
Join Date: Nov 2011
Drives: 2017 Subaru BRZ Limited
Location: socal
Posts: 292
Thanks: 17
Thanked 15 Times in 12 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Anyone else running C38 with non-ACE header? How u like the setup?
stlgrym3 is online now   Reply With Quote
Old 06-06-2018, 01:10 PM   #4582
CSG Mike
 
CSG Mike's Avatar
 
Join Date: Jul 2012
Drives: S2000 CR
Location: Orange County
Posts: 11,702
Thanks: 7,215
Thanked 11,122 Times in 5,342 Posts
Mentioned: 824 Post(s)
Tagged: 13 Thread(s)
Quote:
Originally Posted by stlgrym3 View Post
Anyone else running C38 with non-ACE header? How u like the setup?
Remember, context. On ACN91.

The setup is zero issue when you're flex fuel with significant ethanol content. As I've said in your PMs many times, I do not recommend redlining when on 91.

Because you have an automatic, you need to be especially watchful of this, because heavy throttle application can cause a potentially unwanted downshift, unless you're in manual mode.
CSG Mike is offline   Reply With Quote
Old 06-06-2018, 01:21 PM   #4583
stlgrym3
Senior Member
 
Join Date: Nov 2011
Drives: 2017 Subaru BRZ Limited
Location: socal
Posts: 292
Thanks: 17
Thanked 15 Times in 12 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by CSG Mike View Post
Remember, context. On ACN91.

The setup is zero issue when you're flex fuel with significant ethanol content. As I've said in your PMs many times, I do not recommend redlining when on 91.

Because you have an automatic, you need to be especially watchful of this, because heavy throttle application can cause a potentially unwanted downshift, unless you're in manual mode.
Iím not talking about C38 with HBP, just C38 with stock pulleys and another aftermarket header other than ACE. Basically Iím asking will the following work? Or do I have to go with C30 instead for the following set up?

C38
Non-ACE header (tomei EL in my case)
Factory pulleys
91 petro
Custom tune

I would prefer C38 now even though I wonít be benefiting from its full potentials, but itís good to know the potential is there down the road.
stlgrym3 is online now   Reply With Quote
Old 06-06-2018, 01:28 PM   #4584
Anderzz
Senior Member
 
Anderzz's Avatar
 
Join Date: Jun 2016
Drives: 2013 Subaru BRZ Premium
Location: Maine
Posts: 206
Thanks: 91
Thanked 67 Times in 55 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Garage
Quote:
Originally Posted by stlgrym3 View Post
Iím not talking about C38 with HBP, just C38 with stock pulleys and another aftermarket header other than ACE. Basically Iím asking will the following work? Or do I have to go with C30 instead for the following set up?

C38
Non-ACE header (tomei EL in my case)
Factory pulleys
91 petro
Custom tune

I would prefer C38 now even though I wonít be benefiting from its full potentials, but itís good to know the potential is there down the road.
That will work with a C38.

Sent from my XT1650 using Tapatalk
__________________
Anderzz is offline   Reply With Quote
Old 06-06-2018, 01:34 PM   #4585
CSG Mike
 
CSG Mike's Avatar
 
Join Date: Jul 2012
Drives: S2000 CR
Location: Orange County
Posts: 11,702
Thanks: 7,215
Thanked 11,122 Times in 5,342 Posts
Mentioned: 824 Post(s)
Tagged: 13 Thread(s)
Quote:
Originally Posted by stlgrym3 View Post
Iím not talking about C38 with HBP, just C38 with stock pulleys and another aftermarket header other than ACE. Basically Iím asking will the following work? Or do I have to go with C30 instead for the following set up?

C38
Non-ACE header (tomei EL in my case)
Factory pulleys
91 petro
Custom tune

I would prefer C38 now even though I wonít be benefiting from its full potentials, but itís good to know the potential is there down the road.
That setup will be perfectly fine.
CSG Mike is offline   Reply With Quote
Old 06-06-2018, 01:50 PM   #4586
stlgrym3
Senior Member
 
Join Date: Nov 2011
Drives: 2017 Subaru BRZ Limited
Location: socal
Posts: 292
Thanks: 17
Thanked 15 Times in 12 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by CSG Mike View Post
That setup will be perfectly fine.
Thank you, Iím ready to order Mike :P
stlgrym3 is online now   Reply With Quote
 
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Jackson Racing Supercharger Press Release and Info CounterSpace Garage Forced Induction 110 01-03-2017 10:04 PM
Jackson Racing Rotrex Supercharger System Info and Discussion Jackson Racing Forced Induction 810 05-25-2016 08:46 PM
jackson Racing engine oil cooler - modular to fit the Jackson Racing Supercharger! CSG Mike Forced Induction 24 04-27-2016 12:59 PM
Jackson Racing supercharger NoppyNop Forced Induction 241 06-26-2014 03:05 PM
Jackson Racing Supercharger Pre-Order Sale, $200 off! moto-mike Forced Induction 2 03-05-2014 05:14 PM


All times are GMT -4. The time now is 11:58 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Garage vBulletin Plugins by Drive Thru Online, Inc.