Sprintex 335 Testing & Progress - Page 29 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

SprintexUSA · 09-07-2015, 10:49 AM

Quote:

Originally Posted by smudge

@SprintexUSA

Are you aware of any issues with the 335 units? Just been told that mine may need some "slight adjustments" by the garage...

Could you be a little more specific?

smudge · 09-07-2015, 12:15 PM

Quote:

Originally Posted by SprintexUSA

Could you be a little more specific?

That's all I've been given so far

I've asked the question but not had an answer back yet

SprintexUSA · 09-07-2015, 08:22 PM

I hope they're adjusting fuel capacity, exhaust pipe diameter, and throttlebody size

.

smudge · 09-08-2015, 12:45 PM

Quote:

Originally Posted by SprintexUSA

I hope they're adjusting fuel capacity, exhaust pipe diameter, and throttlebody size

.

Not quite that drastic lol

Been told that my charger doesn't come into the bracket of serial numbers that had a slight issue...but not told what the issue was

Hopefully this time next week I'll have her back

sam69 · 09-15-2015, 04:52 AM

Anyone getting the 335 plus SC with the coated rotors ?

Smudge how's progress going with your setup?

smudge · 09-15-2015, 05:16 AM

Quote:

Originally Posted by sam69

Anyone getting the 335 plus SC with the coated rotors ?

Smudge how's progress going with your setup?

Almost there, engine is all finished

Just a few niggling issues with the oil cooler but then we're ready to get base-mapping and running in underway before changing the oils in a week or so to have a full map and some fun

smudge · 09-18-2015, 11:44 AM

Picking her up tomorrow with a base map limited to 5500rpm for a few hundred miles

sam69 · 09-19-2015, 08:31 AM

Quote:

Originally Posted by smudge

Picking her up tomorrow with a base map limited to 5500rpm for a few hundred miles

The waiting game .

smudge · 09-19-2015, 08:59 AM

Quote:

Originally Posted by sam69

The waiting game .

The wait is over

[ame="https://www.youtube.com/watch?v=CTowc7UxuxU"]GT86 with Sprintex 335 supercharger base map - YouTube[/ame]

Only on a base map for the moment with a 5500rpm limit to let the new engine run in. A few hundred miles on that and then it's back to Abbey for the full tune in a week or so

Dan66 · 09-24-2015, 08:02 AM

Hi Mike,

What is the final build spec (parts and power/tq) of the engine and have you had to do anything to gearbox and diff to withstand the power/torque? Very interested in going down a similar path and would like to work out what this will ultimately involve.

I've page skipped a little through the post so if you have posted the build spec, I missed it sorry.

xwd · 09-25-2015, 02:44 PM

There was some talk about the throttle body in here. I looked at the larger one I have with the TRD setup and the PN is 22030-0S010 which is off a 08-2013 Toyota Tundra. Stupid expensive new but they can be found on Ebay for cheap.

It's the same 6-pin plug as ours. I don't think the bolt spacing is the same though so it wouldn't be a PnP operation to attach it to a manifold.

dallenj · 09-25-2015, 03:35 PM

Quote:

Originally Posted by dwx

There was some talk about the throttle body in here. I looked at the larger one I have with the TRD setup and the PN is 22030-0S010 which is off a 08-2013 Toyota Tundra. Stupid expensive new but they can be found on Ebay for cheap.

It's the same 6-pin plug as ours. I don't think the bolt spacing is the same though so it wouldn't be a PnP operation to attach it to a manifold.

How much larfer than stock is that throttle body.

sato · 09-25-2015, 04:09 PM

It's a 5.7l tb. Looks like it's 70mm

Sent using Tapatalk

dallenj · 09-25-2015, 04:32 PM

Quote:

Originally Posted by sato

It's a 5.7l tb. Looks like it's 70mm

Sent using Tapatalk

What is factory size of throttle body

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
The new sprintex 335 supercharger	jet86	Forced Induction	39	11-01-2014 11:27 AM
Innovate/sprintex SC	rudysaliby	Scion FR-S / Toyota 86 GT86 General Forum	3	10-28-2014 03:14 PM
Innovate/ Sprintex vs vortech	GeeTee86	AFRICA	24	04-04-2014 02:38 PM
Innovate/ Sprintex vs vortech	GeeTee86	AFRICA	5	03-05-2014 07:26 AM
TyperRspec789's Full Blown Stage 1 Base Turbo & e85 Progress and Testing	TyperRspec789	Forced Induction	63	12-31-2013 07:39 PM

09-07-2015, 08:22 PM	#395
SprintexUSA Join Date: Aug 2014 Drives: 2014 FT86 Location: Oklahoma City, OK Posts: 88 Thanks: 15 Thanked 109 Times in 48 Posts Mentioned: 25 Post(s) Tagged: 1 Thread(s)	I hope they're adjusting fuel capacity, exhaust pipe diameter, and throttlebody size .

09-15-2015, 04:52 AM	#397
sam69 Senior Member Join Date: Feb 2014 Drives: GT 86 Location: australia Posts: 369 Thanks: 84 Thanked 121 Times in 77 Posts Mentioned: 3 Post(s) Tagged: 0 Thread(s)	Anyone getting the 335 plus SC with the coated rotors ? Smudge how's progress going with your setup?

09-18-2015, 11:44 AM	#399
smudge Senior Member Join Date: Feb 2015 Drives: Supercharged GT86 Location: UK Posts: 287 Thanks: 75 Thanked 163 Times in 85 Posts Mentioned: 4 Post(s) Tagged: 2 Thread(s)	Picking her up tomorrow with a base map limited to 5500rpm for a few hundred miles

09-24-2015, 08:02 AM	#402
Dan66 Junior Member Join Date: Aug 2015 Drives: Too many to list. Location: Ireland Posts: 5 Thanks: 0 Thanked 2 Times in 1 Post Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Hi Mike, What is the final build spec (parts and power/tq) of the engine and have you had to do anything to gearbox and diff to withstand the power/torque? Very interested in going down a similar path and would like to work out what this will ultimately involve. I've page skipped a little through the post so if you have posted the build spec, I missed it sorry.

09-25-2015, 02:44 PM	#403
xwd Senior Member Join Date: Feb 2012 Drives: 2013 DGM Subaru BRZ (Subie #9) Location: ATL, US Posts: 2,667 Thanks: 123 Thanked 860 Times in 552 Posts Mentioned: 32 Post(s) Tagged: 0 Thread(s)	There was some talk about the throttle body in here. I looked at the larger one I have with the TRD setup and the PN is 22030-0S010 which is off a 08-2013 Toyota Tundra. Stupid expensive new but they can be found on Ebay for cheap. It's the same 6-pin plug as ours. I don't think the bolt spacing is the same though so it wouldn't be a PnP operation to attach it to a manifold.

User Name		Remember Me?
Password