|
Forced Induction Turbo, Supercharger, Methanol, Nitrous |
|
Thread Tools | Search this Thread |
06-05-2015, 06:15 PM | #1 |
Kouki-Monster
Join Date: May 2012
Drives: 2013 Scion FR-S
Location: Saskatoon, SK
Posts: 1,137
Thanks: 11
Thanked 562 Times in 261 Posts
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
|
Header to make gains / improve torque with SC?
Hey guys, short and sweet - I have an HKS V2 SC kit installed with a 43mm restrictor and am tuned on E10 94 Octane.
I am making 248whp right now and still have that dip down low. My question is - has anyone had better luck with one header vs another for forced induction? Mostly looking for power under the curve, torque curve results and the closest to OEM fit.
__________________
Rich Anderson
EMPOWER AUTO |
06-05-2015, 06:26 PM | #2 |
Senior Member
Join Date: Oct 2012
Drives: 2013 Ultramarine FR-S
Location: Liberty Lake
Posts: 1,209
Thanks: 1,978
Thanked 539 Times in 327 Posts
Mentioned: 18 Post(s)
Tagged: 2 Thread(s)
|
Do you have a dyno of your setup? I've got a C30 rotrex, with a JDL UEL with no dip.
Give me a few and I'll dig up my dyno sheet. |
06-05-2015, 06:38 PM | #3 |
Senior Member
Join Date: Oct 2012
Drives: 2013 Ultramarine FR-S
Location: Liberty Lake
Posts: 1,209
Thanks: 1,978
Thanked 539 Times in 327 Posts
Mentioned: 18 Post(s)
Tagged: 2 Thread(s)
|
KW C30, A/T, Base tune, JDL UEL, 3 Inch Header beack.
|
06-08-2015, 11:50 AM | #4 |
Driving Coach
Join Date: Jun 2012
Drives: BRZ
Location: Atlanta
Posts: 3,666
Thanks: 3,723
Thanked 4,137 Times in 1,707 Posts
Mentioned: 90 Post(s)
Tagged: 6 Thread(s)
|
|
06-08-2015, 12:42 PM | #5 |
Sarcastic SOB
Join Date: May 2012
Drives: '13 FR-S M6, '23 Volvo V60 CC
Location: Thornhill Ontario
Posts: 4,614
Thanks: 1,344
Thanked 2,844 Times in 1,635 Posts
Mentioned: 32 Post(s)
Tagged: 3 Thread(s)
|
According to the dyno sheet from the guy that previously had my HKS S/ C w/ header, the torque rise was very linear, no discernible dip. I'll post my dyno after the 18th.
__________________
5:AD kit, HKS V1+ S/C, ECUtek dyno'd, Ohlins MP20, Magnaflow cb, Revworks UEL, Topspeed overpipe, Pinnacle Ceramic tint, VG shark fin, HID's, yellow DRL's, full LEDs, red floor lights, Homelink mirror, trunk lid liner, Perrin LWCP, Valenti smoked, Flossy Grip Tape Shorty, GT86 plaque, lighted vanity mirror, Michelin PSS, Project mU +800, DOT4 fluid, 720 Form GTF1 17x8&9, stitched leather bits, EZ valve.
|
12-18-2019, 08:48 AM | #6 |
Guest
Posts: n/a
Mentioned: Post(s)
Tagged: Thread(s)
|
So has anybody experience which header is the best for an supercharged car?
I´m driving an 2016 BRZ with an HKS Supercharger V3 Kit. Unfortunatly my first engine got destroyed by an catted JDL UEL Header(Catalyzer melted togehter and blocked the exhaust) only 15km after installation. Due the emission laws here in Germany I can´t drive a catless UEL Header. Right now I´m using a modified OEM Header with an 100 Cell HJS Catalyzer but I´m still looking for a durable catted UEL Header. |
12-18-2019, 09:57 AM | #7 |
Senior Member
Join Date: Mar 2018
Drives: 17 Asphalt 86
Location: Ottawa
Posts: 2,172
Thanks: 1,710
Thanked 2,217 Times in 1,132 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
|
You could be cheeky and run a 17+ decatted OEM header. They flow good and will look stock to a visual inspection.
|
The Following User Says Thank You to RToyo86 For This Useful Post: | sroby (12-18-2019) |
12-18-2019, 10:11 AM | #8 |
Senior Member
Join Date: Jan 2017
Drives: brz 2017 hksv2
Location: italy
Posts: 2,196
Thanks: 500
Thanked 1,067 Times in 775 Posts
Mentioned: 65 Post(s)
Tagged: 0 Thread(s)
|
I had a hks uel header with my hks v2 supercharger
When I switcher over to a ACE 350 header I was able to run at least 0.4 leaner and gained almost 2 degrees of ignition timing without knocking, and the torque dip that was present with hks header was total filled up and you could feel the car pulling a lot stronger around 4k rpm I vote for Ace header |
12-18-2019, 11:42 PM | #9 |
Senior Member
Join Date: May 2012
Drives: 2013 Series 10 6MT FR-S
Location: Moreno Valley, CA
Posts: 5,529
Thanks: 1,999
Thanked 2,013 Times in 1,457 Posts
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
|
Or JDL 4-2-1 EL header. Bit cheaper than the ace and works with stock or aftermarket overpipes
Sent from my GM1915 using Tapatalk
__________________
2013 Series 10 FRS #553
RCE T2's, SPC LCAs -4/2.6 camber JDL 4-2-1 EL, FP and OP, Tuned by Zach@CSG on e85 RR Wilwood Front/Rear Sport BBK, Motul 600 Fluid ARC-8 17x9 SX2 GTs 245s/Koing 17x8 v730's 225's |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Which EL Header Correct Torque Dip Best? | slava | Engine, Exhaust, Transmission | 56 | 02-20-2019 07:50 AM |
Header torque specs | Triumphrider | Engine, Exhaust, Transmission | 4 | 06-15-2014 10:09 AM |
Header + Android Torque -Tune | major quicknap | Software Tuning | 4 | 04-29-2014 05:07 PM |
Nut torque for header to block? | Overland'n'5thGEN | Engine, Exhaust, Transmission | 10 | 09-12-2013 11:19 PM |
Torque gains, what does the job? | JoeBoxer | Engine, Exhaust, Transmission | 21 | 10-01-2012 05:46 AM |