|
Software Tuning Discuss all software tuning topics. |
|
Thread Tools | Search this Thread |
12-09-2019, 06:15 AM | #1 |
Senior Member
Join Date: Aug 2018
Drives: turbo frs
Location: worldwide
Posts: 173
Thanks: 122
Thanked 8 Times in 7 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
AFTER FLASH 03TIMES
DEAR steve and all
i have flash oft rom of ZA1JD00C US MY15 6MT throw tactrix openport 2 it download ok the stock rom to car ECU secound i try rom ZA1JA01G stage 1 also downloaded ok to ecu but i try to download again other rom ecuflash gave error msg i try to upload and download not except at all what colud be the issue ??? thnx |
12-09-2019, 09:13 PM | #2 |
Banned
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
|
Take a screenshot of the ecuflash\tactrix logging screen
Make sure ignition full on not just accessory Wait 15 seconds after you tirn ignition full on before trting to read or write to ecu Make sure battery volts with ignition on is 12v or more Reboot pc Check cavles and obd port Try bending both rows of pins on the tactrix adapter inwards very slightly use al old full size SD memory card or similar. |
The Following User Says Thank You to steve99 For This Useful Post: | gt7877 (12-10-2019) |
12-10-2019, 05:42 AM | #3 | |
Senior Member
Join Date: Aug 2018
Drives: turbo frs
Location: worldwide
Posts: 173
Thanks: 122
Thanked 8 Times in 7 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Similar to this image http://s644.photobucket.com/user/agr...p6dlm.jpg.html I removed driver of openport I change tactrix adapter by new one Both gave same error |
|
12-10-2019, 05:43 AM | #4 |
Senior Member
Join Date: Aug 2018
Drives: turbo frs
Location: worldwide
Posts: 173
Thanks: 122
Thanked 8 Times in 7 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
|
12-10-2019, 07:05 AM | #5 |
Senior Member
Join Date: Aug 2018
Drives: turbo frs
Location: worldwide
Posts: 173
Thanks: 122
Thanked 8 Times in 7 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
|
12-10-2019, 07:49 AM | #6 | |
Banned
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
|
Quote:
Are you using tactrix version 2.0 hardware ? As in fhat picture its version 1.3 the older tactrix will not work with bz\86. Also male sure you select brz as vehicle in ecuflash. If it doesnt even read the VIN or the ecu calibration id calid then its almost certianly an obd port connection issue with car. Even on a ecutek flashed ecu tactrix will still read vin and calid. Try testing tactrix on differnt car i think it obd port of car |
|
The Following User Says Thank You to steve99 For This Useful Post: | gt7877 (12-10-2019) |
12-10-2019, 11:58 PM | #7 |
Senior Member
Join Date: Aug 2018
Drives: turbo frs
Location: worldwide
Posts: 173
Thanks: 122
Thanked 8 Times in 7 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Hi Steve
That image just for the same issue I have 2 adapters Openport 2.0 It's read Vin and cid But cannot write or red after flashing 03 times |
12-11-2019, 03:57 AM | #8 | |
Banned
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
|
Quote:
Ok if it reads vin and calid the connection is provably ok. But if you can do a test read on another car to check tactrix would be good. I assume ecu has not ben locked by ecutek or BRZEdit ?. And car starts and runs fine ? try removing battery terminal for 30 minutes, then replace connection, then try flasging at first turn on of ignition |
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
SOLD: Open Flash Tablet, Open Flash Header, Crawford Power Blocks | Totemo_Hayai | Engine, Exhaust, Bolt-Ons | 14 | 09-15-2019 02:28 AM |
My experience with Shiv & his products at Open Flash Tablet / Open Flash Header | TouchMyHonda | User/Vendor/Sponsor Reviews, Feedback, Comments | 5 | 10-23-2015 09:57 AM |
FS: open flash headers / open flash tablet - SOLD | alanhung85 | Canada Classifieds | 12 | 02-10-2015 02:08 PM |
EcuTek Flash finished but now it shows only a Partial Flash... | Cross | Software Tuning | 32 | 02-12-2014 10:55 AM |