follow ft86club on our blog, twitter or facebook.
FT86CLUB
Ft86Club
Delicious Tuning
Register Garage Members List Calendar Search Today's Posts Mark Forums Read

Go Back   Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > Technical Topics > Software Tuning

Software Tuning Discuss all software tuning topics.


User Tag List

Reply
 
Thread Tools Search this Thread
Old 01-25-2016, 04:22 PM   #1
Grip Ronin
The Mechanic
 
Grip Ronin's Avatar
 
Join Date: Mar 2012
Drives: Civic Turbo,FR-S
Location: NJ
Posts: 928
Thanks: 130
Thanked 171 Times in 119 Posts
Mentioned: 2 Post(s)
Tagged: 1 Thread(s)
a/f command problem

So ive been using, logging and tuning on oft since just about when it was released for this car but ive never encountered this problem. I went turbo about 3 months back and put on shivs base map, it seem to run fine and log fine for a while but recently its started to give weird readings while cruising.
On start up the car will only go as high as 14.2 when it should be 14.7, after about 10 min of driving i will notice it creeping richer and richer until its about 12.9 at partial throttle actual af and commanded. around this point the car will little by little stay in closed loop longer and the command will read 15.05 but actual af will be 12s-13s light throttle. During full throttle it sometimes goes to open loop and af actual and command is normally about right. I have no fault codes and no noticed exhaust leaks. I have tried different maps and reflashing it. shiv is leaning towards 02 sensor but id like to know if anyone has some knowledge on this before i drop a couple hundred on a sensor.
this is a pic of it cruising on the highway, fully warmed up.
Attached Images
 
__________________
IG-Joey_Soul
Progress Thread Ported billet 20G
Grip Ronin is offline   Reply With Quote
Old 01-25-2016, 04:23 PM   #2
go_a_way1
Not Bаnned Anymore
 
go_a_way1's Avatar
 
Join Date: Jan 2015
Drives: Heavily Modified FRS
Location: Calgary, AB
Posts: 9,827
Thanks: 14,918
Thanked 8,274 Times in 4,797 Posts
Mentioned: 355 Post(s)
Tagged: 374 Thread(s)
Quote:
Originally Posted by Grip Ronin View Post
So ive been using, logging and tuning on oft since just about when it was released for this car but ive never encountered this problem. I went turbo about 3 months back and put on shivs base map, it seem to run fine and log fine for a while but recently its started to give weird readings while cruising.
On start up the car will only go as high as 14.2 when it should be 14.7, after about 10 min of driving i will notice it creeping richer and richer until its about 12.9 at partial throttle actual af and commanded. around this point the car will little by little stay in closed loop longer and the command will read 15.05 but actual af will be 12s-13s light throttle. During full throttle it sometimes goes to open loop and af actual and command is normally about right. I have no fault codes and no noticed exhaust leaks. I have tried different maps and reflashing it. shiv is leaning towards 02 sensor but id like to know if anyone has some knowledge on this before i drop a couple hundred on a sensor.
this is a pic of it cruising on the highway, fully warmed up.
Don't quote me but isn't the window our ECU see fairly small? I didn't think it would read past certain readings both high and low.
__________________
Quote:
Originally Posted by 1GiantTurtle View Post
This thread got de-railed quick now it's just about Penis guitars
go_a_way1 is offline   Reply With Quote
Old 01-25-2016, 11:12 PM   #3
Grip Ronin
The Mechanic
 
Grip Ronin's Avatar
 
Join Date: Mar 2012
Drives: Civic Turbo,FR-S
Location: NJ
Posts: 928
Thanks: 130
Thanked 171 Times in 119 Posts
Mentioned: 2 Post(s)
Tagged: 1 Thread(s)
Quote:
Originally Posted by go_a_way1 View Post
Don't quote me but isn't the window our ECU see fairly small? I didn't think it would read past certain readings both high and low.
i believe you can set your limits and scaling inside romraider
__________________
IG-Joey_Soul
Progress Thread Ported billet 20G
Grip Ronin is offline   Reply With Quote
The Following User Says Thank You to Grip Ronin For This Useful Post:
go_a_way1 (01-26-2016)
Old 01-26-2016, 01:25 AM   #4
steve99
Banned
 
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
commanded afr is the afr the ecu is targeting
afr is the measeured afr at front o2 sensor

maybe check maf is clean, no intake leaks check catch cans an pcv valves etc

if its a boost leak past maf, maf will meter the air then some lost so it will run rich as less air getting to engine than maf saw.

yep you can rescale front o2 to read down to about 10 afr with reasnoble accuracy, stock scaling stops at about 12 from memory
steve99 is offline   Reply With Quote
The Following User Says Thank You to steve99 For This Useful Post:
go_a_way1 (01-26-2016)
Old 01-26-2016, 08:12 AM   #5
go_a_way1
Not Bаnned Anymore
 
go_a_way1's Avatar
 
Join Date: Jan 2015
Drives: Heavily Modified FRS
Location: Calgary, AB
Posts: 9,827
Thanks: 14,918
Thanked 8,274 Times in 4,797 Posts
Mentioned: 355 Post(s)
Tagged: 374 Thread(s)
Quote:
Originally Posted by Grip Ronin View Post
i believe you can set your limits and scaling inside romraider
Quote:
Originally Posted by steve99 View Post
commanded afr is the afr the ecu is targeting
afr is the measeured afr at front o2 sensor

maybe check maf is clean, no intake leaks check catch cans an pcv valves etc

if its a boost leak past maf, maf will meter the air then some lost so it will run rich as less air getting to engine than maf saw.

yep you can rescale front o2 to read down to about 10 afr with reasnoble accuracy, stock scaling stops at about 12 from memory
Okay sweet I am glad I was right
Is it possible that the AFR difference he is seeing is due to thr fact that the stock ecu cant read far enough in either direction to match the commanded AFR?
__________________
Quote:
Originally Posted by 1GiantTurtle View Post
This thread got de-railed quick now it's just about Penis guitars
go_a_way1 is offline   Reply With Quote
Old 01-26-2016, 08:46 AM   #6
Grip Ronin
The Mechanic
 
Grip Ronin's Avatar
 
Join Date: Mar 2012
Drives: Civic Turbo,FR-S
Location: NJ
Posts: 928
Thanks: 130
Thanked 171 Times in 119 Posts
Mentioned: 2 Post(s)
Tagged: 1 Thread(s)
Quote:
Originally Posted by steve99 View Post
commanded afr is the afr the ecu is targeting
afr is the measeured afr at front o2 sensor

maybe check maf is clean, no intake leaks check catch cans an pcv valves etc

if its a boost leak past maf, maf will meter the air then some lost so it will run rich as less air getting to engine than maf saw.

yep you can rescale front o2 to read down to about 10 afr with reasnoble accuracy, stock scaling stops at about 12 from memory
so your thinking the maf would cause it to throw inaccurate commands like that? 15:05 is what it wil throw on decel
__________________
IG-Joey_Soul
Progress Thread Ported billet 20G
Grip Ronin is offline   Reply With Quote
Old 01-26-2016, 10:49 AM   #7
phrosty
Senior Member
 
Join Date: Apr 2013
Drives: 2013 FR-S
Location: Seattle
Posts: 806
Thanks: 202
Thanked 320 Times in 199 Posts
Mentioned: 18 Post(s)
Tagged: 1 Thread(s)
afaik Commanded AFR of 15 shouldn't happen unless it's cutting fuel e.g. you're decelerating.
__________________
2013 Whiteout 6AT FR-S | Perrin Inlet Tube + 2.75" CAI | OpenFlash Header | P&L Catback | 4.88 Final Drive | Dialed in OFT 2.0x Stage 2 E85 | 18x8 Enkei Raijin + 225/40 Michelin Pilot Super Sport | 17x7 Stock + 215/45 Michelin X-Ice Xi-2
phrosty is offline   Reply With Quote
Old 01-26-2016, 04:42 PM   #8
steve99
Banned
 
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
yes it very weird the ecu commanded afr is 15 and engine load 0.48,

i dont know whats in tune tables but it very difficult to get the ecu to target anything leaner than 14.7 under load

The open loop fuel table generally wont let you target anthing leaner than 14.7

and closed loop table is an offset from 14.7 ie values are generally negitive eg -0.3 in closed loop table ,ecu will target 14.7 - 0.3=14.4

if you put positive values or zero in the closed loop table then weird stuff happens ltft is disabled.

also i once messed up my closed loop table by highlighting entire table and applying an offset in romraider it leaned out all the cells richer than 14.7 , and the cells at 14.7 showed 14.7 , but when i drove the car it targeted rearly lean values. I had to copy in a fresh table to fix it even though it looked ok something was weird.

if you try to enter values leaner than 14.7 manually romraider wont allow it.

maybe it a rearly weird tune corruption

Last edited by steve99; 01-26-2016 at 05:08 PM.
steve99 is offline   Reply With Quote
Old 01-26-2016, 04:47 PM   #9
steve99
Banned
 
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
Quote:
Originally Posted by go_a_way1 View Post
Okay sweet I am glad I was right
Is it possible that the AFR difference he is seeing is due to thr fact that the stock ecu cant read far enough in either direction to match the commanded AFR?
the stock o2 sensor scaling will read as lean as 20 on deceleration fuel cut.
steve99 is offline   Reply With Quote
The Following User Says Thank You to steve99 For This Useful Post:
go_a_way1 (01-26-2016)
Old 01-27-2016, 10:09 AM   #10
Grip Ronin
The Mechanic
 
Grip Ronin's Avatar
 
Join Date: Mar 2012
Drives: Civic Turbo,FR-S
Location: NJ
Posts: 928
Thanks: 130
Thanked 171 Times in 119 Posts
Mentioned: 2 Post(s)
Tagged: 1 Thread(s)
Quote:
Originally Posted by steve99 View Post
yes it very weird the ecu commanded afr is 15 and engine load 0.48,

i dont know whats in tune tables but it very difficult to get the ecu to target anything leaner than 14.7 under load

The open loop fuel table generally wont let you target anthing leaner than 14.7

and closed loop table is an offset from 14.7 ie values are generally negitive eg -0.3 in closed loop table ,ecu will target 14.7 - 0.3=14.4

if you put positive values or zero in the closed loop table then weird stuff happens ltft is disabled.

also i once messed up my closed loop table by highlighting entire table and applying an offset in romraider it leaned out all the cells richer than 14.7 , and the cells at 14.7 showed 14.7 , but when i drove the car it targeted rearly lean values. I had to copy in a fresh table to fix it even though it looked ok something was weird.

if you try to enter values leaner than 14.7 manually romraider wont allow it.

maybe it a rearly weird tune corruption
ya exactly but this is a base turbo map from shiv. everyone else gets the same thing lol. it didnt use to do this. funny cause it doesnt even try to run what the command is, it just goes rich the whole time never leaner then 13.0 under throttle while it says 15.05...my values are 14.7 at the leanest, but when i start the car it will command 14.2 and get richer and richer till it locks out and just says 15.05.. im at a loss
__________________
IG-Joey_Soul
Progress Thread Ported billet 20G
Grip Ronin is offline   Reply With Quote
Old 01-28-2016, 10:00 AM   #11
Grip Ronin
The Mechanic
 
Grip Ronin's Avatar
 
Join Date: Mar 2012
Drives: Civic Turbo,FR-S
Location: NJ
Posts: 928
Thanks: 130
Thanked 171 Times in 119 Posts
Mentioned: 2 Post(s)
Tagged: 1 Thread(s)
Quote:
Originally Posted by steve99 View Post
the stock o2 sensor scaling will read as lean as 20 on deceleration fuel cut.
http://datazap.me/u/grip-hooligan/ri...og=0&data=1-10

here is a log of it if you wanted to take a peak. maybe kodename has an idea (i dont know how to tag people on here)
__________________
IG-Joey_Soul
Progress Thread Ported billet 20G
Grip Ronin is offline   Reply With Quote
Old 01-28-2016, 05:14 PM   #12
steve99
Banned
 
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
Quote:
Originally Posted by Grip Ronin View Post
http://datazap.me/u/grip-hooligan/ri...og=0&data=1-10

here is a log of it if you wanted to take a peak. maybe kodename has an idea (i dont know how to tag people on here)
hmm certianly weird when it gous open loop it seem to go strange and hold open loop and afr and commanded afr drift apart.

i did not study logs when i had that open loop table issue but it did similar thing,

kodename 47 is on holidays sking to tag just put @ infront of username
steve99 is offline   Reply With Quote
Old 01-28-2016, 08:06 PM   #13
Grip Ronin
The Mechanic
 
Grip Ronin's Avatar
 
Join Date: Mar 2012
Drives: Civic Turbo,FR-S
Location: NJ
Posts: 928
Thanks: 130
Thanked 171 Times in 119 Posts
Mentioned: 2 Post(s)
Tagged: 1 Thread(s)
Quote:
Originally Posted by steve99 View Post
hmm certianly weird when it gous open loop it seem to go strange and hold open loop and afr and commanded afr drift apart.

i did not study logs when i had that open loop table issue but it did similar thing,

kodename 47 is on holidays sking to tag just put @ infront of username
so i swapped maps again, at first it was kinda retarted while idling it would flicker 10.0 af then back to 14.7 then the oft shut off i adjusted the cable and the car has been perfect all day. command and all staying at 14.7 when it should, no freaking out after weeks of it doing that its just fine i guess its ok now lol
__________________
IG-Joey_Soul
Progress Thread Ported billet 20G
Grip Ronin is offline   Reply With Quote
Old 01-28-2016, 10:36 PM   #14
steve99
Banned
 
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
Quote:
Originally Posted by Grip Ronin View Post
so i swapped maps again, at first it was kinda retarted while idling it would flicker 10.0 af then back to 14.7 then the oft shut off i adjusted the cable and the car has been perfect all day. command and all staying at 14.7 when it should, no freaking out after weeks of it doing that its just fine i guess its ok now lol
Id give it a couple of days and at least a 100 miles or more driving before you get too excited it may be related to some weird fuel trim learning or something else that only shows up after a while.

this maybe why people dont see it they only log just after a flash possibly and not after a week or so.
steve99 is offline   Reply With Quote
 
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Dash Command App and Oil Temp on iPhone and iPad nzer Scion FR-S / Toyota 86 GT86 General Forum 38 03-19-2017 12:33 PM
Dash command for BOOST Flat_4_Life Forced Induction 5 01-18-2016 12:13 PM
idle afr is 14.05? command and actual...what gives? Lytheum Issues | Warranty | Recalls / TSB 1 06-24-2013 01:21 PM
Voice or GUI command to pause guidance? Sovran Electronics | Audio | NAV | Infotainment 0 09-25-2012 02:21 PM
handsfree voice command help lbroskee Electronics | Audio | NAV | Infotainment 5 09-13-2012 04:51 PM


All times are GMT -4. The time now is 09:27 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.

Garage vBulletin Plugins by Drive Thru Online, Inc.