|
DIY (Do-It-Yourself) Guides For all DIYs. |
|
Thread Tools | Search this Thread |
10-28-2012, 11:36 AM | #1 |
Photo Specialist
Join Date: Feb 2012
Drives: 2013 Toyota 86 DGM 6MT
Location: Texas
Posts: 1,152
Thanks: 587
Thanked 1,802 Times in 420 Posts
Mentioned: 94 Post(s)
Tagged: 0 Thread(s)
|
DIY - Strut Tower Brace - FT-86 SpeedFactory
Houston86.com DIY Back again. This time we'll be installing a strut tower brace. We focus on the @FT-86 SpeedFactory version, but this should transfer easily to other vendor's products. The main difference that other braces may actually use the three bolts on the actual strut itself. I'll highlight in a separate post. It's fairly simple to install; you don't even have to jack up your vehicle! It does reduces body roll which I do not like.
Full thoughts and closeups in this post: http://www.ft86club.com/forums/showthread.php?t=20863 As always I am not responsible for any damage done to your vehicle. Please be safe. 20121025-FT86SpeedFactoryStrutTowerBraceDIY-01 by VictorN07, on Flickr Service Manual 20121025-FT86SpeedFactoryStrutTowerBraceDIY-02 by VictorN07, on Flickr 20121025-FT86SpeedFactoryStrutTowerBraceDIY-03 by VictorN07, on Flickr Check out the DIY for the alternate hood prop position here: http://www.ft86club.com/forums/showthread.php?t=20912 20121025-FT86SpeedFactoryStrutTowerBraceDIY-04 by VictorN07, on Flickr 20121025-FT86SpeedFactoryStrutTowerBraceDIY-05 by VictorN07, on Flickr Be careful not to drop your hardware! 20121025-FT86SpeedFactoryStrutTowerBraceDIY-06 by VictorN07, on Flickr 20121025-FT86SpeedFactoryStrutTowerBraceDIY-08 by VictorN07, on Flickr 20121025-FT86SpeedFactoryStrutTowerBraceDIY-09 by VictorN07, on Flickr 20121025-FT86SpeedFactoryStrutTowerBraceDIY-10 by VictorN07, on Flickr The OEM braces have markings to indicate Right and Left. Although reversible, we zip tie the end that goes on the firewall in case we have to reuse them later. 20121025-FT86SpeedFactoryStrutTowerBraceDIY-11 by VictorN07, on Flickr 20121025-FT86SpeedFactoryStrutTowerBraceDIY-12 by VictorN07, on Flickr 20121025-FT86SpeedFactoryStrutTowerBraceDIY-13 by VictorN07, on Flickr 20121025-FT86SpeedFactoryStrutTowerBraceDIY-14 by VictorN07, on Flickr 20121025-FT86SpeedFactoryStrutTowerBraceDIY-15 by VictorN07, on Flickr Torque to specified values in the service manual 20121025-FT86SpeedFactoryStrutTowerBraceDIY-17 by VictorN07, on Flickr This part is optional 20121025-FT86SpeedFactoryStrutTowerBraceDIY-18 by VictorN07, on Flickr You can buy this at any hardware store 20121025-FT86SpeedFactoryStrutTowerBraceDIY-19 by VictorN07, on Flickr 20121025-FT86SpeedFactoryStrutTowerBraceDIY-20 by VictorN07, on Flickr 20121025-FT86SpeedFactoryStrutTowerBraceDIY-21 by VictorN07, on Flickr 20121025-FT86SpeedFactoryStrutTowerBraceDIY-22 by VictorN07, on Flickr
__________________
Last edited by F1point4; 10-29-2012 at 12:23 AM. |
The Following 4 Users Say Thank You to F1point4 For This Useful Post: | FT-86 SpeedFactory (10-28-2012), kykpress (10-28-2012), tripjammer (01-25-2013), Yamaha_R6 (09-05-2014) |
10-28-2012, 11:41 AM | #2 |
Photo Specialist
Join Date: Feb 2012
Drives: 2013 Toyota 86 DGM 6MT
Location: Texas
Posts: 1,152
Thanks: 587
Thanked 1,802 Times in 420 Posts
Mentioned: 94 Post(s)
Tagged: 0 Thread(s)
|
For those products which mount to the stop of the actual strut using the three bolts use these pictures as your reference. A 12mm deep socket is required
20121025-StrutTowerBraceDIYAlt-01 by VictorN07, on Flickr 20121025-StrutTowerBraceDIYAlt-02 by VictorN07, on Flickr
__________________
Last edited by F1point4; 10-28-2012 at 11:56 AM. |
The Following User Says Thank You to F1point4 For This Useful Post: | FT-86 SpeedFactory (10-28-2012) |
10-28-2012, 12:34 PM | #3 |
Banned
Join Date: Aug 2012
Drives: VortechSC,BorlaEL,Perrin,GCRace
Location: HighHeatHighAltitudeAZ,USA
Posts: 2,254
Thanks: 458
Thanked 669 Times in 394 Posts
Mentioned: 9 Post(s)
Tagged: 2 Thread(s)
|
nice what does it weigh please?
|
10-28-2012, 04:01 PM | #4 |
Photo Specialist
Join Date: Feb 2012
Drives: 2013 Toyota 86 DGM 6MT
Location: Texas
Posts: 1,152
Thanks: 587
Thanked 1,802 Times in 420 Posts
Mentioned: 94 Post(s)
Tagged: 0 Thread(s)
|
I knew I forgot something. Didn't weigh it, but carrying it, it isn't more than 2-3 lbs. the stock bars I can weigh soon.
__________________
|
10-28-2012, 04:30 PM | #5 |
Boosted
Join Date: Jul 2012
Drives: Sideways
Location: Atlanta Georgia USA
Posts: 2,377
Thanks: 388
Thanked 716 Times in 414 Posts
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
|
VERY interesting. Won't fit my car but interested to see how it holds up for others.
__________________
Nismo 370Z 300whp -> FR-S Turbo 450whp on E85 -> Z06 Corvette 500whp
|
|
|
Tags |
diy, ft-86 speedfactory, strut tower brace |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
New Release - FT-86 SpeedFactory - Strut Tower Bar / Tri-Bar | FT-86 SpeedFactory | Suspension | Chassis | Brakes -- Sponsored by 949 Racing | 28 | 10-25-2013 04:42 PM |
**NEW PRODUCT** FT-86 Speed Factory - Strut Tower / Engine Brace Bars | FT-86 SpeedFactory | Brakes, Suspension, Chassis | 35 | 06-04-2013 09:27 PM |
SRT Strut Tower Triangulation Bar | Swift Racing Technologies | Brakes, Suspension, Chassis | 34 | 10-24-2012 05:15 AM |
Front Strut Tower Bar Question | russv | Scion FR-S / Toyota 86 GT86 General Forum | 29 | 05-22-2012 02:00 AM |