follow ft86club on our blog, twitter or facebook.
FT86CLUB
Ft86Club
Speed By Design
Register Garage Community Calendar Today's Posts Search

Go Back   Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > Technical Topics > Engine, Exhaust, Transmission

Engine, Exhaust, Transmission Discuss the FR-S | 86 | BRZ engine, exhaust and drivetrain.


User Tag List

Reply
 
Thread Tools Search this Thread
Old 01-08-2014, 02:27 PM   #1
Mikem53
Senior Member
 
Join Date: Apr 2013
Drives: FR-S 6MT
Location: Somewhere in Space
Posts: 1,565
Thanks: 500
Thanked 882 Times in 433 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Nameless axle back - Install and initial impression.

My Nameless axleback 2.5" with 5" mufflers arrived yesterday, but it was too
fricken cold to install it. But I did unbox it and admired my purchase.
The exhaust was very well packed and was wrapped to protect the tips from
scratches.
I waited until it warmed up to 25 degrees and the sun was shining on my garage door before I was up to the install challenge. A cup of coffee in hand and some warm thoughts and I was ready to tackle this puppy.
I backed up onto my rhino ramps and proceeded to remove the stock 1960's looking cadillac muffler from the car.
I carefully removed the 14mm bolts and fished out the gasket to reuse.
Next was getting rubber hangers to give up their grip on the stock muffler..
Some gloves and foul language were all that was needed to eventually un-hang the OEM axleback piece.
I then suspended the new exhaust in place on the hangers and slipped the gasket into place and tightened it up. To my surprise, no adjustments were necessary after I straightened out the hangers onto the muffler supports.
Checked and rechecked clearances, admired the look, which is so much better!
and then fired it up.
Major difference in sound. A very low tone growl but not obnoxious or too loud.
Now it sounds like a sports car ! Took it for a drive and its what I was hoping for. Nice deep tone, smooth and not obnoxious at all.. No drone either from what I am able to tell so far. The tips look great from any angle and really dresses up the rear!
One of the easier exhaust systems I ever installed.
Glad I decided not to go for the Milltek.. saved $1K in the process and ended up with the sound I was looking for.
Thanks to @humfrz for the sound clip and suggestion!

Last edited by Mikem53; 01-09-2014 at 07:52 PM.
Mikem53 is offline   Reply With Quote
The Following 5 Users Say Thank You to Mikem53 For This Useful Post:
brenesk91 (01-08-2014), Gunman (01-08-2014), humfrz (01-08-2014), Ryan@Nameless (01-09-2014), SirBrass (01-08-2014)
Old 01-08-2014, 05:09 PM   #2
bleakhand
Junior Member
 
Join Date: Dec 2013
Drives: 2014 BRZ
Location: Minneapolis
Posts: 9
Thanks: 0
Thanked 1 Time in 1 Post
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Garage
Curious about how is the 4" muffler comparing to the 5" in sound?
bleakhand is offline   Reply With Quote
Old 01-08-2014, 05:22 PM   #3
Mikem53
Senior Member
 
Join Date: Apr 2013
Drives: FR-S 6MT
Location: Somewhere in Space
Posts: 1,565
Thanks: 500
Thanked 882 Times in 433 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by bleakhand View Post
Curious about how is the 4" muffler comparing to the 5" in sound?
I don't know.. I went for the quiet one.. It's plenty loud for me. A noticeable difference from stock. These are real pipes.. Not just a large muffler can like OEM. Sounds nice..
Mikem53 is offline   Reply With Quote
Old 01-08-2014, 07:26 PM   #4
humfrz
Senior Member
 
Join Date: May 2013
Drives: 2013 FR-S, white, MT
Location: Puyallup, WA
Posts: 29,868
Thanks: 28,790
Thanked 31,816 Times in 16,425 Posts
Mentioned: 708 Post(s)
Tagged: 2 Thread(s)
Quote:
Originally Posted by Mikem53 View Post
My Nameless axleback 2.5" with 5" mufflers arrived yesterday, ............!
Good show, Mikem53 ....... congratulations on sticking with the install and not whimping out like I did....

(maybe I just didn't use enough foul language on the hangars ..... )

I'm glad you like the sound ..... you do realize it adds at least 10 whp ..... according to my ear dyno ....

humfrz
humfrz is offline   Reply With Quote
Old 01-08-2014, 07:33 PM   #5
WRB5titch
Senior Member
 
Join Date: Aug 2013
Drives: WRBrz
Location: SoCal
Posts: 142
Thanks: 374
Thanked 67 Times in 41 Posts
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by bleakhand View Post
Curious about how is the 4" muffler comparing to the 5" in sound?
I have the 4" muffler but I haven't been in an 86 with the 5" muffler so I can't give a direct comparison. BUT I can compare it to @DAEMANO who has the TRD axleback and my nameless is only so slightly louder than the TRD (from inside the cabin anyway)

I'm not complaining though, I love the sound.
WRB5titch is offline   Reply With Quote
Old 01-08-2014, 07:59 PM   #6
Mikem53
Senior Member
 
Join Date: Apr 2013
Drives: FR-S 6MT
Location: Somewhere in Space
Posts: 1,565
Thanks: 500
Thanked 882 Times in 433 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by humfrz View Post
Good show, Mikem53 ....... congratulations on sticking with the install and not whimping out like I did....

(maybe I just didn't use enough foul language on the hangars ..... )

I'm glad you like the sound ..... you do realize it adds at least 10 whp ..... according to my ear dyno ....

humfrz
I thought about folding the seat down and tossing it in the back and taking it to a muffler shop.. but since it warmed up some here in NC,
I thought I would have a go at it.. with the ramps and my creeper..
it was cake.
Mikem53 is offline   Reply With Quote
The Following User Says Thank You to Mikem53 For This Useful Post:
humfrz (01-08-2014)
Old 01-08-2014, 08:52 PM   #7
wlwarfield
VTECLOL
 
wlwarfield's Avatar
 
Join Date: Aug 2013
Drives: 2011 STi & 2013 F150 SVT Raptor
Location: Fort Worth, Texas
Posts: 355
Thanks: 169
Thanked 184 Times in 105 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Garage
I have had a Nameless Exhaust on my STi for a year and half now. I love it. Great quality, fitment, & sound
__________________
follow me on Instagram @wlwarfield
OFFICIAL Texas BRZ, FRS, GT86 Facebook Page
OFFICIAL NM86CLUB Facebook Page
2011 Subaru Impreza WRX STi sedan
2013 Ford F-150 SVT Raptor
wlwarfield is offline   Reply With Quote
Old 01-08-2014, 08:59 PM   #8
FR-S Matt
Banned
 
Join Date: Nov 2012
Drives: 2013 Ultramarine FR-S MT
Location: Round Rock, TX
Posts: 3,941
Thanks: 679
Thanked 1,771 Times in 1,111 Posts
Mentioned: 38 Post(s)
Tagged: 0 Thread(s)
Garage
I loved my Nameless axleback when I had it by itself. I made a mistake of going with a 3" exhaust and made it too loud and droney. Had I have gone 2.5", I probably would have been just fine with the stock midpipe. Amazing quality on their parts.
FR-S Matt is offline   Reply With Quote
Old 01-09-2014, 12:28 AM   #9
ALbadboy
Senior Member
 
ALbadboy's Avatar
 
Join Date: Sep 2012
Drives: 2013 Subaru BRZ Limited (WRB MT)
Location: Mobile, Alabama
Posts: 146
Thanks: 19
Thanked 62 Times in 33 Posts
Mentioned: 18 Post(s)
Tagged: 1 Thread(s)
Mine came in today as well, we must have been put in the same batch. I definitely agree. Nice low growl, zero drone, & looks great. 10/10 would order again.
ALbadboy is offline   Reply With Quote
The Following User Says Thank You to ALbadboy For This Useful Post:
Ryan@Nameless (01-09-2014)
Old 01-09-2014, 07:39 AM   #10
Mikem53
Senior Member
 
Join Date: Apr 2013
Drives: FR-S 6MT
Location: Somewhere in Space
Posts: 1,565
Thanks: 500
Thanked 882 Times in 433 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by ALbadboy View Post
Mine came in today as well, we must have been put in the same batch. I definitely agree. Nice low growl, zero drone, & looks great. 10/10 would order again.
Ordered Black Friday.. Took awhile.. but worth the wait..
Mikem53 is offline   Reply With Quote
Old 01-09-2014, 09:14 AM   #11
zc06_kisstherain
 
zc06_kisstherain's Avatar
 
Join Date: Aug 2012
Drives: SWP BRZ
Location: NJ
Posts: 3,177
Thanks: 723
Thanked 667 Times in 507 Posts
Mentioned: 15 Post(s)
Tagged: 2 Thread(s)
Garage
I love mine with 2.5 4" muffler.
I paired up with Motiv front pipe catless. sounds great
zc06_kisstherain is offline   Reply With Quote
Old 01-09-2014, 05:49 PM   #12
Ryan@Nameless
Senior Member
 
Ryan@Nameless's Avatar
 
Join Date: Jun 2012
Drives: 2014 SWP BRZ Limited
Location: Vancouver, WA
Posts: 114
Thanks: 102
Thanked 462 Times in 78 Posts
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Glad you enjoy it!

-Ryan @ Nameless
Ryan@Nameless is offline   Reply With Quote
Old 10-21-2015, 02:50 PM   #13
Cmorris8848
Senior Member
 
Cmorris8848's Avatar
 
Join Date: Apr 2015
Drives: CWP 2015 BRZ Stock
Location: Valdosta, GA
Posts: 280
Thanks: 346
Thanked 168 Times in 109 Posts
Mentioned: 2 Post(s)
Tagged: 1 Thread(s)
I realize this is a dead thread, but I'm looking to purchase a Nameless Axle back soon, and this was the first thread that popped up when searching on Google. I have a few questions:

1) Did you order off of Nameless's site, and if not, what site?

2) About how long did it take to get to you?

Thank you in advance to any help
Cmorris8848 is offline   Reply With Quote
Old 10-21-2015, 03:14 PM   #14
MisterSheep
Killed Scion
 
MisterSheep's Avatar
 
Join Date: Jun 2015
Drives: 2013 FR-S Whiteout
Location: East Bay, CA
Posts: 7,721
Thanks: 8,285
Thanked 7,307 Times in 4,485 Posts
Mentioned: 334 Post(s)
Tagged: 185 Thread(s)
Garage
Quote:
Originally Posted by Cmorris8848 View Post
I realize this is a dead thread, but I'm looking to purchase a Nameless Axle back soon, and this was the first thread that popped up when searching on Google. I have a few questions:

1) Did you order off of Nameless's site, and if not, what site?

2) About how long did it take to get to you?

Thank you in advance to any help
I would cross shop and see which has the best prices with shipping etc. Usually it's a good idea to buy directly from the manufacturer but sometimes there might be a cheaper option.
__________________
Miyuki みゆき "Beautiful Snow" The Whiteout FR-S
Instagram: trevor.parque
Quote:
Originally Posted by KR-S 86 View Post
What are you talking about? You just killed one of the worst brands in history according to enthusiasts. People will be worshipping you like sheep.
MisterSheep is offline   Reply With Quote
 
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Nameless axle back and downpipe Cade01 Engine, Exhaust, Bolt-Ons 23 12-28-2013 08:32 PM
Works ABM vs. Nameless axle back 4in mufflers BlackyRose Engine, Exhaust, Transmission 12 08-29-2013 11:11 PM
Possible trade? Nameless axle-back for Perrin Resonated Cat-back GTB/ZR-1 Engine, Exhaust, Bolt-Ons 0 03-26-2013 01:51 PM
Nameless Performance Revised Offset Axle Back Exhaust stockysnail Engine, Exhaust, Transmission 23 03-19-2013 12:23 PM


All times are GMT -4. The time now is 12:05 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.

Garage vBulletin Plugins by Drive Thru Online, Inc.