AVO Turbo Kit Owners Topic

[protpibe]

Originally Posted by Astroboy

What clutch Are you guys running with this kit? I think I might have smoked my stock clutch

Sent from my LG-D850 using Tapatalk

Exedy stage 1. I like it, but the gear rattle is annoying as hell. I probably wouldn't use the flywheel if I had to go back and do it over

[Astroboy]

Originally Posted by protpibe

Exedy stage 1. I like it, but the gear rattle is annoying as hell. I probably wouldn't use the flywheel if I had to go back and do it over

Exedy stage 1 on your car? How much power are you making? Did because I think I remembered reading that the clutch is rated at 200tq

Sent from my LG-D850 using Tapatalk

[protpibe]

Originally Posted by Astroboy

Exedy stage 1 on your car? How much power are you making? Did because I think I remembered reading that the clutch is rated at 200tq

Sent from my LG-D850 using Tapatalk

I think around 240wtq (310whp) when I dyno'd it last, but I've since increased the boost. No slips anywhere. The exedy stage 1 is rated to 200tq, but it will hold much more. I'm assuming it comes at the cost of excessively fast wear lol

From what I remember reading, the exedy Stage 2 will have nearly an identical pedal feel, but be rated to a higher torque number.

[Astroboy]

Originally Posted by protpibe

I think around 240wtq (310whp) when I dyno'd it last, but I've since increased the boost. No slips anywhere. The exedy stage 1 is rated to 200tq, but it will hold much more. I'm assuming it comes at the cost of excessively fast wear lol

From what I remember reading, the exedy Stage 2 will have nearly an identical pedal feel, but be rated to a higher torque number.

Ok, it's official, I ordered my stage 2 then. Thanks. 2 more questions, would you recommend I swap my flywheel to since I burned my stock clutch, and how much stiffer is your exedy clutch compared to the oem one? I like the smooth pedal feel of my stock clutch

Sent from my LG-D850 using Tapatalk

[SkAsphalt]

Originally Posted by protpibe

Exedy stage 1. I like it, but the gear rattle is annoying as hell. I probably wouldn't use the flywheel if I had to go back and do it over

TRUTH!

But I guess we put up with it...because race car

[Draco_PR23]

I have the exedy stage 2 (old revision) and there were some of us with problems like gear lockup and stuff; there is a thread about it. The new stage 2 revision I think it uses oem flywheel... I'm in the process of getting a new clutch soon and people recommended me ACT

[Astroboy]

Originally Posted by Draco_PR23

I have the exedy stage 2 (old revision) and there were some of us with problems like gear lockup and stuff; there is a thread about it. The new stage 2 revision I think it uses oem flywheel... I'm in the process of getting a new clutch soon and people recommended me ACT

Did you install the exedy yourself? Which ones the old version? I ordered mine from ft86speedfactory

Sent from my LG-D850 using Tapatalk

[Draco_PR23]

Originally Posted by Astroboy

Did you install the exedy yourself? Which ones the old version? I ordered mine from ft86speedfactory

Sent from my LG-D850 using Tapatalk

Yes with a friend who is a mechanic, I installed the clutch by Sept/2014.

Here is some pics of the old rev. Stage 2, in the last pic you can see the P/N: http://www.ft86club.com/forums/showp...0&postcount=11

This is the thread about the problems we had: http://www.ft86club.com/forums/showthread.php?t=75445

[Astroboy]

Originally Posted by Draco_PR23

Yes with a friend who is a mechanic, I installed the clutch by Sept/2014.

Here is some pics of the old rev. Stage 2, in the last pic you can see the P/N: http://www.ft86club.com/forums/showp...0&postcount=11

This is the thread about the problems we had: http://www.ft86club.com/forums/showthread.php?t=75445

Does it come with instructions that show torque specs for clutch bolts? I'm going to install it with a friend to

Sent from my LG-D850 using Tapatalk

[Draco_PR23]

Originally Posted by Astroboy

Does it come with instructions that show torque specs for clutch bolts? I'm going to install it with a friend to

Sent from my LG-D850 using Tapatalk

It does have some overall instructions; about the torque specs you could found them in the service manual I think which you can find it in the forum. Also there is a diy thread which helped me a lot

[Astroboy]

@protpibe do you have any quarter mile times wile you were pushing 240whp? Dynojet correct

Sent from my LG-D850 using Tapatalk

[Astroboy]

Originally Posted by Draco_PR23

It does have some overall instructions; about the torque specs you could found them in the service manual I think which you can find it in the forum. Also there is a diy thread which helped me a lot

I'm about to install mine tomorrow, I want to know what lubricant I'm supposed to use on the throwout bearing. I might need to go to o'reilys to get it, but don't know what it's called. Also, what lubricant must I use on the shifter when reinstalling


Sent from my iPad using Tapatalk

[Astroboy]

Originally Posted by Draco_PR23

It does have some overall instructions; about the torque specs you could found them in the service manual I think which you can find it in the forum. Also there is a diy thread which helped me a lot

I finally installed mine yesterday, and after 5 miles, it started making a weird grinding noise when decelerating. Do you know what it could be?

Sent from my LG-D850 using Tapatalk

[Astroboy]

Originally Posted by protpibe

I think around 240wtq (310whp) when I dyno'd it last, but I've since increased the boost. No slips anywhere. The exedy stage 1 is rated to 200tq, but it will hold much more. I'm assuming it comes at the cost of excessively fast wear lol

From what I remember reading, the exedy Stage 2 will have nearly an identical pedal feel, but be rated to a higher torque number.

I really need your help with an issue I'm having. You see, I recently installed my clutch by myself, and now, i hear a gear grinding noise Every time I decelerate is this normal?

Sent from my LG-D850 using Tapatalk