Official OpenFlash Tablet FA20 Tuning Tech Discussion Thread

[steve99]

Originally Posted by shiv@vishnu

I would definitely revise the ignition map judging by the logs. Assuming you can't run higher grade fuel, the first step would be retard 1 degree under load between 5k-6k rpm. And retard 1.5 degrees above 6k and try again. And the re-test. You probably wont need to retard more than that.

Thanks

I try that and log again

[Nardi330]

Originally Posted by shiv@vishnu

I would definitely revise the ignition map judging by the logs. Assuming you can't run higher grade fuel, the first step would be retard 1 degree under load between 5k-6k rpm. And retard 1.5 degrees above 6k and try again. And the re-test. You probably wont need to retard more than that.

hi Shiv, should i also do the same as @steve99 mentioned that i have similar issue here.

here is my log:

http://www.datazap.me/u/nardi330/22-...2-12&solo=2-12

i'm running Perrin drop in filter, Perrin Over pipe, Perrin front pipe with high flow cat and Perrin catback. Would i be better to switch to stage 2 EL rom?

thanks.

[uncivilised]

my first log

http://www.datazap.me/u/uncivilised/...&data=1-7-8-11

first fill up for e85, filled 42 litres.

60km so far

stock car using stg2 el e85 tune

Am i on the right track so far? i realise ill need to drive more for the tune to settle. i notice the kc learned drops to 3 at around 6500rpm and iam is pegged at 1.


also if i flash to e85 stage 2 EL and still use a stock header, then later i add my 4-1 catless EL header (im waiting for them to be ceramic coated), will the tune adjust automatically to the header or will i need to reflash?

[01s0uljah]

Just got the OFT and tried loading the Stage 1 tunes the tablet but it says:

The file selected is not compliant

I'm using the OTS 1.58 release..

I also wiped the tunes that came with it.. :\

[Shiv@Openflash]

Originally Posted by 01s0uljah

Just got the OFT and tried loading the Stage 1 tunes the tablet but it says:

The file selected is not compliant

I'm using the OTS 1.58 release..

I also wiped the tunes that came with it.. :\

It sounds like you are trying to a load a ROM with a different CAL ID than your original. So if your original ROM is say, a A01C make sure you load a tune with the suffix A01C.

Any reason you didn't use the OTS tunes that it came pre-loaded with?

-shiv

[DarkSunrise]

Originally Posted by shiv@vishnu

It sounds like you are trying to a load a ROM with a different CAL ID than your original. So if your original ROM is say, a A01C make sure you load a tune with the suffix A01C.

Any reason you didn't use the OTS tunes that it came pre-loaded with?

-shiv

Shiv,

I'm thinking about buying an OFT to go along with the Nameless 4-2-1 EL header that was just released. Is there an OFT map that would work for this header? In other words, do you have a shelf map that would work for a catless EL header?

Thanks!

[Shiv@Openflash]

Originally Posted by DarkSunrise

Shiv,

I'm thinking about buying an OFT to go along with the Nameless 4-2-1 EL header that was just released. Is there an OFT map that would work for this header? In other words, do you have a shelf map that would work for a catless EL header?

Thanks!

Yes indeed. Just use our Stage 2 EL map

[Luckrider]

Originally Posted by DarkSunrise

Shiv,

I'm thinking about buying an OFT to go along with the Nameless 4-2-1 EL header that was just released. Is there an OFT map that would work for this header? In other words, do you have a shelf map that would work for a catless EL header?

Thanks!

Stage2 EL for 91+ or e85 comes preloaded right on the tablet

[gramicci101]

Newb question: is an OFT stage 1 (eventually stage 2) 91+ map something I can set and forget? I'm not going to use E85 or add forced induction, so I'm not going to get esoteric with it. Once flashed, I'd prefer to leave it alone and let it do its thing.

[Shiv@Openflash]

Originally Posted by gramicci101

Newb question: is an OFT stage 1 (eventually stage 2) 91+ map something I can set and forget? I'm not going to use E85 or add forced induction, so I'm not going to get esoteric with it. Once flashed, I'd prefer to leave it alone and let it do its thing.

That is the whole idea behind the the OTS maps.

[gramicci101]

Wonderful. Once I get to my next base I will buy one. I'm in transit right now, so I'll have to wait. Thanks for the quick response.

[01s0uljah]

Originally Posted by shiv@vishnu

It sounds like you are trying to a load a ROM with a different CAL ID than your original. So if your original ROM is say, a A01C make sure you load a tune with the suffix A01C.

Any reason you didn't use the OTS tunes that it came pre-loaded with?

-shiv

I didn't do my research and erased the ones it came with so I could load new ones in. I jumped the gun

I was able to get the stage 1 tune on and can instantly notice a difference. I'm new to the whole Open Flash Scene.. I'm running a completely stock Auto BRZ with a K/N air filter.. I'm guessing I should be running only Stage 1?

What would happen if I ran stage 2 on a stock car?

[Migero86]

Got my tablet in... Came pre-loaded with all I needed to cover my mods... Flashed the Stage2 UEL tune running on 94 oct and so far the car is running awesome... I am sure as I put more miles on the tune it will adapt even more. For now, its already running smoother then the OEM tune and this truly is how the car should be.

[Shiv@Openflash]

Originally Posted by 01s0uljah

I didn't do my research and erased the ones it came with so I could load new ones in. I jumped the gun

I was able to get the stage 1 tune on and can instantly notice a difference. I'm new to the whole Open Flash Scene.. I'm running a completely stock Auto BRZ with a K/N air filter.. I'm guessing I should be running only Stage 1?

What would happen if I ran stage 2 on a stock car?

Glad to hear it! On a stock car, definitely run a Stage 1 map as Stage 2 will likely make the car run a bit rich.

Shiv