OFFICIAL Torque Android app PID/Misc Thread - Page 57 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Somerandom18 · 02-10-2017, 11:06 PM

Anyone know how accurate the HP reading is? I put in the gross weight (car with fluids) plus 200 lbs to account for me and junk. Says I'm putting down 197hp at 6900 rpm. Seems a bit high for an untuned car..

Sent from my Pixel XL using Tapatalk

Jajanken86 · 02-11-2017, 02:26 AM

Quote:

Originally Posted by Somerandom18

Anyone know how accurate the HP reading is? I put in the gross weight (car with fluids) plus 200 lbs to account for me and junk. Says I'm putting down 197hp at 6900 rpm. Seems a bit high for an untuned car..

Sent from my Pixel XL using Tapatalk

Is that BHP or WHP?

Sent from my iDroid

churchx · 02-11-2017, 06:20 AM

It's obd app reporting by some unknown calculations readings. Not something actually measured at crank or wheels as on dyno. So neither. Just "some reading" i wouldn't care about unlike eg. oil/water temps and so on ..

allowe · 02-17-2017, 09:56 AM

How accurate is WHP ??? I'd be stunned if it gave an accurate reading. I have an iPhone and I'm using dash command which was about 15 bucks. It has saved my life a lot using it to reset my codes and reading live data. The horsepower number on dash command seems to be almost on point.. but you'd never really know

Sent from my iPhone using Tapatalk

djwishbone · 03-18-2017, 12:15 PM

Has anyone ever tried to create their own ethanol gauge? Theoretically it should be possible right? Since most of us are using the rear O2 sensor for our flex fuel gauge input to the ecu. I can see the O2 sensor voltage, but I think it uses frequency and not just a standard voltage to relay ethanol level? Just wondering if anyone else has played with this. My delicious app is not very reliable stability wise and it would be awesome to get this integrated into my torque pro gauges!

Chronology · 04-12-2017, 04:59 PM

Anyone know the PID for gear selector?

BIAbenny · 04-19-2017, 11:04 AM

Apologize if someone have already mentioned it, but has there been a work around with shutting off the car with Torque on will cause the CEL U0073 come on? I have been hesitant to use the app on the track in case of a spin off or forgetting to quit the app after pitting the car.

GsxrMe · 04-19-2017, 07:19 PM

Quote:

Originally Posted by BIAbenny

Apologize if someone have already mentioned it, but has there been a work around with shutting off the car with Torque on will cause the CEL U0073 come on? I have been hesitant to use the app on the track in case of a spin off or forgetting to quit the app after pitting the car.

Ya i did it at the gym so many times, I just bought gauges. It really pisses me off too because I used my old Samsung S4 for the Torque app.

nos145 · 05-14-2017, 07:06 PM

Quote:

Originally Posted by BIAbenny

Apologize if someone have already mentioned it, but has there been a work around with shutting off the car with Torque on will cause the CEL U0073 come on? I have been hesitant to use the app on the track in case of a spin off or forgetting to quit the app after pitting the car.

I am interested in this as well. Has anyone been getting issues lately?

aRex · 06-20-2017, 10:39 PM

Looking for VVT angles; not available in torque pro app...

Overdrive · 07-12-2017, 08:44 PM

It's possible I missed it, but I did look through this thread just about completely. So is there a way of getting the oil temp PID to read in Fahrenheit? I already had Torque set to display things in °F, but the way the PID is detailed in this thread is for display in Celsius, so that's what gets displayed for that one gauge.

lazyluka · 07-12-2017, 10:45 PM

Quote:

Originally Posted by Overdrive

It's possible I missed it, but I did look through this thread just about completely. So is there a way of getting the oil temp PID to read in Fahrenheit? I already had Torque set to display things in °F, but the way the PID is detailed in this thread is for display in Celsius, so that's what gets displayed for that one gauge.

Have you tried to change the unit type and equation part in Torque?

From post #2:
Unit type: C
Equation: AC-40 (no space between A and C; "AC" is the location within the response)

Try:
Unit type: F
Equation: (AC-40)×1.8+32

You may also need to convert the Min and Max from C to F as well.

Overdrive · 07-13-2017, 09:36 AM

I did try that, but I think I may have jacked up the parentheses when I did. Thanks.

lazyluka · 07-13-2017, 03:44 PM

Quote:

Originally Posted by Overdrive

I did try that, but I think I may have jacked up the parentheses when I did. Thanks.

Also, try the * instead of the x for multiplication.

04-12-2017, 04:59 PM	#790
Chronology Senior Member Join Date: Aug 2016 Drives: 13' Satin White Pearl BRZ Location: Claremont, CA Posts: 193 Thanks: 44 Thanked 70 Times in 53 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Anyone know the PID for gear selector? __________________ RS*R Sport-I w/custom spring rate / Cusco Front/Rear Sways, Cusco Diff Brace / Cusco Power Brace (Rear/Front/Upper/Lower) / JDL UEL Headers / INVIDIA Q300 Ti / Valenti Revo Tails and rear backup/ EcuTek / Moto-East Flexfuel / Moto-East E85 tune

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Torque app for android question	Brody602	Electronics \| Audio \| NAV \| Infotainment	8	01-08-2015 04:53 PM
Torque for Android	Freeman	Scion FR-S / Toyota 86 GT86 General Forum	7	11-22-2012 11:05 PM
Android Torque app questions	Craig	Engine, Exhaust, Transmission	1	11-12-2012 04:14 PM
Bluetooth OBD scanner and Android Torque - less than 25 shipped	whataboutbob	Engine, Exhaust, Transmission	7	10-20-2012 01:15 PM
Android Tablet + torque	CharlieChaos	Electronics \| Audio \| NAV \| Infotainment	3	10-04-2012 08:23 PM

02-10-2017, 11:06 PM	#785
Somerandom18 Senior Member Join Date: Sep 2016 Drives: 2017 manual BRZ Location: USA Posts: 467 Thanks: 322 Thanked 178 Times in 111 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	Anyone know how accurate the HP reading is? I put in the gross weight (car with fluids) plus 200 lbs to account for me and junk. Says I'm putting down 197hp at 6900 rpm. Seems a bit high for an untuned car.. Sent from my Pixel XL using Tapatalk

02-11-2017, 06:20 AM	#787
churchx Senior Member Join Date: Mar 2015 Drives: 2014 GT86 Location: Latvia, Riga Posts: 4,333 Thanks: 696 Thanked 2,085 Times in 1,436 Posts Mentioned: 53 Post(s) Tagged: 1 Thread(s)	It's obd app reporting by some unknown calculations readings. Not something actually measured at crank or wheels as on dyno. So neither. Just "some reading" i wouldn't care about unlike eg. oil/water temps and so on ..

02-17-2017, 09:56 AM	#788
allowe Senior Member Join Date: Sep 2016 Drives: FR-S Location: mississauga Posts: 576 Thanks: 227 Thanked 122 Times in 89 Posts Mentioned: 7 Post(s) Tagged: 0 Thread(s)	How accurate is WHP ??? I'd be stunned if it gave an accurate reading. I have an iPhone and I'm using dash command which was about 15 bucks. It has saved my life a lot using it to reset my codes and reading live data. The horsepower number on dash command seems to be almost on point.. but you'd never really know Sent from my iPhone using Tapatalk

03-18-2017, 12:15 PM	#789
djwishbone Last Starfighter Join Date: Jul 2016 Drives: 2016 FR-S Series 2.0 Location: Sonoran Desert Posts: 118 Thanks: 36 Thanked 43 Times in 29 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Has anyone ever tried to create their own ethanol gauge? Theoretically it should be possible right? Since most of us are using the rear O2 sensor for our flex fuel gauge input to the ecu. I can see the O2 sensor voltage, but I think it uses frequency and not just a standard voltage to relay ethanol level? Just wondering if anyone else has played with this. My delicious app is not very reliable stability wise and it would be awesome to get this integrated into my torque pro gauges!

04-19-2017, 11:04 AM	#791
BIAbenny Junior Member Join Date: Nov 2014 Drives: 2013 Subaru BRZ Limited Location: Newton, MA Posts: 4 Thanks: 0 Thanked 0 Times in 0 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Apologize if someone have already mentioned it, but has there been a work around with shutting off the car with Torque on will cause the CEL U0073 come on? I have been hesitant to use the app on the track in case of a spin off or forgetting to quit the app after pitting the car.

06-20-2017, 10:39 PM	#794
aRex Junior Member Join Date: Sep 2016 Drives: '13 BRZ '97 Dak Location: STL Posts: 1 Thanks: 0 Thanked 0 Times in 0 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Looking for VVT angles; not available in torque pro app...

User Name		Remember Me?
Password