Austin

[vanetix]

Originally Posted by Turkish

Anything in the evening during the week will work best for my work schedule. I am about to come off of having weekends off as a project I was working on is coming to a close. I imagine it would be easier to negotiate some sort of arrangement if we sit down to eat early like about 5-6pm. I believe the big dinner rush is generally between 6-8pm. As far as getting parking arranged, I think that will depend on the location and how much parking they have available.



I got my rear diff crush washers from the dealer today. I am a little hesitant to post the part #'s as there seemed to be some confusion from the parts dept on just "which differential" they went to? That said, if they aren't the right thing I can reuse the old ones by flipping them over and I do not want to confuse anyone with wrong part #'s!

Don't flip them! One side has a lip on it that is meant to crush down, the other side was a bit harder and didn't seal well in my experience. Source: I made the mistake of flipping it and had a small leak I had to worry about for 3000 miles

[Turkish]

Originally Posted by vanetix

Don't flip them! One side has a lip on it that is meant to crush down, the other side was a bit harder and didn't seal well in my experience. Source: I made the mistake of flipping it and had a small leak I had to worry about for 3000 miles

I guess I hope I have the right things then!

Sent from my SCH-I535 using Tapatalk

[missbrz]

@Turkish unfortunately something came up i got to go to houston first time in the morning so i wont be able to go to DIY Texas with the group . i really hope i can get these springs in soon though

[Turkish]

Originally Posted by missbrz

@Turkish unfortunately something came up i got to go to houston first time in the morning so i wont be able to go to DIY Texas with the group . i really hope i can get these springs in soon though

That's unfortunate, I hope all works out for the best! Maybe we can coordinate something with @trevorovert, since he will have his headers to install soon!?

[Turkish]

Updating the list, it looks like it will be me for 30 minutes and @Yellow13 for a couple hours. I'll be sure to call and cancel the second lift during my lunch break tomorrow.

[missbrz]

Originally Posted by Turkish

That's unfortunate, I hope all works out for the best! Maybe we can coordinate something with @trevorovert, since he will have his headers to install soon!?

that sounds good just let me know when you guys plan on going

[86-tundra]

Hopefully sometime next week I'll be there.. but I'll be there tomorrow too. around 5:30 probably. I've got a meeting till 5:30 but it probably won't last that long

i'll probably bring my camera and snap some pics of whatever installs are going on, FFS

who all is going and when are y'all gonna be there?

[FR-S Matt]

Originally Posted by Scottemad123

While I agree fully, there are no tuners of note even close to local. Yes there is a ECUtek master shop outside of San Antonio, but no mention of tunes from them on this board really, and I don't want to be their guinea pig. Not exactly excited about doing street logs for remote tunes either. Plus a little competition is nice, and I like seeing what the two sides bring to the table, will cause a little more innovation.

Boost Logic here in Austin has an Ecutek master tuner named Junior. He's been tuning Subaru's for at least 15 years. He did Po's turbo FR-S tune on the dyno. I am considering him tuning me on the dyno. Dynotronics in New Braunfels has a master tuner too, and D3 performance in Houston. There's quite a few, they're all just not on the forums a lot.

[Turkish]

Speaking of Po, when is he getting on the forum?

Sent from my SCH-I535 using Tapatalk

[Scottemad123]

Originally Posted by FR-S Matt

Boost Logic here in Austin has an Ecutek master tuner named Junior. He's been tuning Subaru's for at least 15 years. He did Po's turbo FR-S tune on the dyno. I am considering him tuning me on the dyno. Dynotronics in New Braunfels has a master tuner too, and D3 performance in Houston. There's quite a few, they're all just not on the forums a lot.

Blah, why can't delicious tuning or drift office be down here would be a much easier choice

What time are people wrenching tonight?

[Turkish]

Originally Posted by Scottemad123

What time are people wrenching tonight?

Reservations are for 5-9pm


Sent from my SCH-I535 using Tapatalk

[Scottemad123]

Knew I should have brought my coat to work...whoops.

[86-tundra]

Originally Posted by Scottemad123

Knew I should have brought my coat to work...whoops.

i'm in the same boat.. brought a change of clothes so I can head over after, but a little unprepared for the cold.

[FR-S Matt]

I will try to make it guys. Just had new carpet laid in my apartment so I had to move everything around in the place to make that happen. Almost like I was moving out but not.