|
Cosmetic Modification (Interior/Exterior/Lighting) Discussions about cosmetic mods. |
|
Thread Tools | Search this Thread |
02-10-2014, 04:43 PM | #1 |
Senior Member
Join Date: Apr 2013
Drives: 2013 FRS hot lava
Location: renton,wa
Posts: 201
Thanks: 169
Thanked 81 Times in 59 Posts
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
|
Winjet wobble
I just got a set of winjet headlights today. While I was checking them out I noticed that the right headlight projector seems to have a tiny bit of play. Anyone else with winjets experience a small amount of "looseness/play" with the projectors?
|
02-10-2014, 07:11 PM | #2 |
Member
Join Date: Dec 2013
Drives: Whiteout FRS
Location: Reseda,CA
Posts: 41
Thanks: 6
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Yeah, seems to wobble a bit for many other headlights as well, but that's fine.
Aslong as the alignment of the beam doesn't mess up while your driving you should be fine. retrofitted some projectors on mine since I hated the ones that came with it and holds well, wobbles a bit but sits properly in there without play while driving |
02-10-2014, 10:57 PM | #5 |
Member
Join Date: Dec 2013
Drives: Whiteout FRS
Location: Reseda,CA
Posts: 41
Thanks: 6
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
not needed..
|
02-11-2014, 12:52 AM | #6 |
Senior Member
Join Date: Jul 2012
Drives: '23 CWP BRZ
Location: Jacksonville, FL
Posts: 1,665
Thanks: 1,262
Thanked 1,126 Times in 533 Posts
Mentioned: 45 Post(s)
Tagged: 0 Thread(s)
|
|
02-11-2014, 02:47 PM | #7 |
Senior Member
Join Date: Apr 2013
Drives: 2013 FRS hot lava
Location: renton,wa
Posts: 201
Thanks: 169
Thanked 81 Times in 59 Posts
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
|
Bouncy....well its the projector itself that seems to have play. If i grasp the back of the projector and wiggle it or shake the whole light assembly, the projector moves a bit and makes a light clunk noise like something might be loose.
|
02-11-2014, 04:20 PM | #8 |
Senior Member
Join Date: Apr 2013
Drives: 2013 FRS hot lava
Location: renton,wa
Posts: 201
Thanks: 169
Thanked 81 Times in 59 Posts
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
|
I played with the driver side light a bit. It does the same thing. Since the movement is so minimal I'm going to assume its normal and I am just too anal. I'll check the stock lights when I pull them out.
|
02-11-2014, 05:23 PM | #9 |
Troll Hunter
Join Date: Aug 2013
Drives: fr-s, tundra
Location: Somewhere
Posts: 1,424
Thanks: 1,695
Thanked 922 Times in 470 Posts
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
|
If you notice shake in the project's cutoff, then that is wrong. IE you're driving on a bumpy road and your cutoff moves up and down independent of your travel.
you can usually prevent shake in the cutoff by tightening the projector. not sure how it works on the winjet, speaking from experience with other retrofits
__________________
|
02-11-2014, 08:21 PM | #10 |
Senior Member
Join Date: Jun 2013
Drives: RX-7 / BRZ
Location: USA
Posts: 2,343
Thanks: 1,026
Thanked 2,501 Times in 1,081 Posts
Mentioned: 27 Post(s)
Tagged: 0 Thread(s)
|
This is very common with spyder aftermarket lights on many platforms too, one easy solution is to apply 3m weatherstripping to the bottom of the lights. (The 3m weatherstripping comes in a 8' roll for around $30.00 with tape already applied to one side.) Stick it to either the bottom of the bumper or the bottom of the light, this will stiffen up the lights, and dampen any vibrations. The weatherstripping can be found at any auto parts store. A lot of times it is due to the plastic housing, cheaper/less plastic, ect.
|
The Following User Says Thank You to Kiske For This Useful Post: | beaver_scott (02-11-2014) |
02-11-2014, 10:00 PM | #11 |
Senior Member
Join Date: Jul 2012
Drives: 2013 Asphalt FR-S Manual
Location: Whitby, ON, Canada
Posts: 6,716
Thanks: 7,875
Thanked 3,351 Times in 2,134 Posts
Mentioned: 99 Post(s)
Tagged: 1 Thread(s)
|
^^ It sounds like it's the actual projector inside the housing that is loose, not the whole housing bouncing around in the car?
__________________
Light travels faster than sound, so people may appear to be bright until you hear them speak... flickr |
02-11-2014, 10:02 PM | #12 |
Senior Member
Join Date: Apr 2013
Drives: 2013 FRS hot lava
Location: renton,wa
Posts: 201
Thanks: 169
Thanked 81 Times in 59 Posts
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
|
|
02-14-2014, 03:55 PM | #13 |
Senior Member
Join Date: Jun 2012
Drives: Argento FR-S
Location: Socal
Posts: 392
Thanks: 296
Thanked 247 Times in 123 Posts
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
|
Just got mine earlier this week and I'm having the same issue on the passenger side headlight. My beam of light bounces up and down everytime I hit a bump or crack on the road. Anyone know if this is covered under Winjet's warranty?
|
02-14-2014, 04:24 PM | #14 | |
Senior Member
Join Date: Apr 2013
Drives: 2013 FRS hot lava
Location: renton,wa
Posts: 201
Thanks: 169
Thanked 81 Times in 59 Posts
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
|
Winjet wobble
Quote:
Crap. Guess I better hold off on installing mine until I figure out how to tighten the projector. I don't want bouncy lights! |
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Crank Pully Wobble... With video | Norcalmav23 | Engine, Exhaust, Transmission | 33 | 09-25-2019 07:26 PM |
Wobble, falling apart, loose joints? | imravenit | Issues | Warranty | Recalls / TSB | 25 | 03-29-2015 10:02 PM |
Winjet HID Size? | Jeremehh | Cosmetic Modification (Interior/Exterior/Lighting) | 9 | 03-10-2014 02:28 AM |
FS: Winjet Chrome Headlights | civicdrivr | Exterior Parts (Aero, Lighting, Etc.) | 6 | 01-16-2014 11:33 PM |
Custom Purple Winjet and Black Winjet Headlights | xclusive_brett | Cosmetic Modification (Interior/Exterior/Lighting) | 35 | 12-17-2013 08:28 AM |