11-18-2014, 02:06 PM | #1 |
Senior Member
Join Date: Dec 2013
Drives: 13 BRZ Limited, 2000 Impreza Sport
Location: Eden Prairie, Minnesota
Posts: 139
Thanks: 80
Thanked 50 Times in 32 Posts
Mentioned: 2 Post(s)
Tagged: 2 Thread(s)
|
Painting Inside OEM Tails
This was my approach to painting the guts of my oem tail lights. I didn't plan on making a diy when I did it so some steps are not documented thoroughly. But with a little common sense you will nail it, I have faith in you. Overall this DIY was a 6/10 difficulty. The most important part is patience. Note that this pertains to the painting process only, the thread I used as a guide to getting them open is here
http://www.ft86club.com/forums/showthread.php?t=12489 BEFORE I did not have a soldering iron handy, so I opted to heat a utility knife with a propane torch to do my cutting. I heated the blade red hot, cut about an inch, reheated, etc. It took about 40 minutes per side to open them, but I was happy with how clean the cuts turned out. I replaced the orange lamps with these. Be warned they had to be slightly trimmed on the bottom to fit, but not altogether difficult to do http://www.ebay.com/itm/like/120599815957?lpid=82 No fancy paint here, rusto for the housing and vht nightshade for the reflective bits. Very light dustings and a lot of time recommended. HINDSIGHT: I ended up painting the border a seperate color (white). If you opt to do this, paint the border color on first, then block it off and black out the rest. I did it backwards and it caused a lot of extra time taping. Also, the little reflective cove the blinker sits in is where most of the blinker light comes from. I only sprayed 1 light coat over this and blocked it off for the rest of the spraying to keep it somewhat reflective. To achieve a border, paint it the color of your choosing then block it off with this tape before spraying the rest of the housing. It worked perfectly. http://www.autobodytoolmart.com/3m-v...FcLtMgodYX0Ajg Pennies fit the recessed brake light circles perfectly, I like the effect it gave in the end. 3M carbon fiber vinyl wrap laid on top. I experimented wrapping different sections but in the end just kept the top. I wanted to stay subtle. Comparison, note rustoleum gloss white paint was used for the outline. Again, the best way to achieve this is to cover the outline with your chosen color, let it completely dry, lay a line of tape over the outline, spray the rest back. I screwed them back together and used this to keep the water out as recommended in previous posts. Dont worry, you cant see it with the trunk open! http://www.ebay.com/itm/like/271515501709?lpid=82 Only one side installed currently, I'll add better day and night pics once completely finished. The cf vinyl can only be seen up close, wrap it or don't! Total cost: about $30 Total time: 1 weekend to 1 week. Don't tape on uncured paint! I learned this lesson about 3 times during this project. GOOD LUCK
__________________
Innovate powered- Corn fed- FBM tuned
|
The Following 13 Users Say Thank You to poorsche For This Useful Post: | amaciose (11-19-2014), booyaka (11-25-2014), Cliu91 (11-21-2014), GotBRZ1691 (05-01-2015), itsbirdy (11-19-2014), Jake_86 (03-13-2015), Lorico (03-22-2015), PBlack09 (11-24-2014), Premium 615 (12-27-2015), randomthoughts (08-20-2015), Shedd22 (04-29-2015), tato.valverde (04-29-2015), willypongtb (11-21-2014) |
11-18-2014, 03:24 PM | #2 |
Join Date: Aug 2012
Drives: SWP BRZ
Location: NJ
Posts: 3,177
Thanks: 723
Thanked 667 Times in 507 Posts
Mentioned: 15 Post(s)
Tagged: 2 Thread(s)
|
wow! it looks great! but i dont have gut to do this project
|
The Following User Says Thank You to zc06_kisstherain For This Useful Post: | poorsche (11-18-2014) |
11-18-2014, 03:27 PM | #3 |
Senior Member
Join Date: Dec 2013
Drives: 13 BRZ Limited, 2000 Impreza Sport
Location: Eden Prairie, Minnesota
Posts: 139
Thanks: 80
Thanked 50 Times in 32 Posts
Mentioned: 2 Post(s)
Tagged: 2 Thread(s)
|
Oh its really not that bad!
__________________
Innovate powered- Corn fed- FBM tuned
|
11-18-2014, 09:08 PM | #5 |
Senior Member
Join Date: Oct 2013
Drives: Lightning Red '13 Limited BRZ
Location: Atlanta, GA
Posts: 346
Thanks: 87
Thanked 112 Times in 73 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
You could make some good money offering to do this for people. I wouldn't have the guts to do this myself either...
Sent from my Nexus 10 using Tapatalk |
The Following User Says Thank You to lastexile1987 For This Useful Post: | poorsche (11-21-2014) |
11-19-2014, 01:12 AM | #6 |
Senior Member
Join Date: Jun 2014
Drives: 2014 Satin White Pearl GTS auto
Location: Kyalami- South Africa
Posts: 301
Thanks: 11
Thanked 163 Times in 83 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
very very nice, and on a white car, it really does make a huge difference! now as stated above, if I only had the cojones to actually pull the trigger
__________________
2002 MR2 Spyder 2zz-GE Apexi PFC PPE Race header 8500 RPM of FUN
2014 37J 86 Auto |
The Following User Says Thank You to WesleyG For This Useful Post: | poorsche (11-21-2014) |
11-19-2014, 01:18 AM | #7 | |
Senior Member
Join Date: Dec 2013
Drives: 13 BRZ Limited, 2000 Impreza Sport
Location: Eden Prairie, Minnesota
Posts: 139
Thanks: 80
Thanked 50 Times in 32 Posts
Mentioned: 2 Post(s)
Tagged: 2 Thread(s)
|
Quote:
__________________
Innovate powered- Corn fed- FBM tuned
|
|
11-19-2014, 01:45 AM | #8 |
FRSKEE
Join Date: Aug 2013
Drives: 2014 Monogram Series Whiteout
Location: 909
Posts: 322
Thanks: 130
Thanked 83 Times in 67 Posts
Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
|
Need to do this. Already have an extra set of tails.
|
The Following User Says Thank You to Alain For This Useful Post: | poorsche (11-21-2014) |
11-19-2014, 03:07 AM | #9 |
Senior Member
Join Date: Dec 2013
Drives: 13 BRZ Limited, 2000 Impreza Sport
Location: Eden Prairie, Minnesota
Posts: 139
Thanks: 80
Thanked 50 Times in 32 Posts
Mentioned: 2 Post(s)
Tagged: 2 Thread(s)
|
Give it a go man, you have nothing to lose! I'd say that the most important material is the tape. Masking tape or even "painter's tape" do not cut it for doing the housing outline...I had a couple of re-do's before I was satisfied. I really recommend purchasing the tape in the link. If you pull the trigger on this be sure to post up some photos!
__________________
Innovate powered- Corn fed- FBM tuned
|
11-20-2014, 05:18 PM | #10 |
Senior Member
Join Date: Sep 2014
Drives: 2014 Frs
Location: California
Posts: 262
Thanks: 9
Thanked 70 Times in 49 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
Did you really just use dimes to cover up those LEDs when painting your brake lights?
|
11-20-2014, 05:29 PM | #11 |
Senior Member
Join Date: Dec 2013
Drives: 13 BRZ Limited, 2000 Impreza Sport
Location: Eden Prairie, Minnesota
Posts: 139
Thanks: 80
Thanked 50 Times in 32 Posts
Mentioned: 2 Post(s)
Tagged: 2 Thread(s)
|
No, pennies
__________________
Innovate powered- Corn fed- FBM tuned
|
11-20-2014, 05:30 PM | #12 |
Senior Member
Join Date: Sep 2014
Drives: 2014 Frs
Location: California
Posts: 262
Thanks: 9
Thanked 70 Times in 49 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
They are a perfect fit?
|
11-20-2014, 05:46 PM | #13 |
Senior Member
Join Date: Dec 2013
Drives: 13 BRZ Limited, 2000 Impreza Sport
Location: Eden Prairie, Minnesota
Posts: 139
Thanks: 80
Thanked 50 Times in 32 Posts
Mentioned: 2 Post(s)
Tagged: 2 Thread(s)
|
Perfect fit. When the paint dries, flip the light over, the pennies fall out and you have perfect red circles in their place.
__________________
Innovate powered- Corn fed- FBM tuned
|
11-20-2014, 08:01 PM | #14 | |
Never on Time Always Late
Join Date: Jun 2012
Drives: #silenced crickets
Location: Norcal
Posts: 578
Thanks: 86
Thanked 152 Times in 101 Posts
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
|
Quote:
I'd basically want something similar to yours -Keep chrome edge -Light tint on red led circle/side marker (use pennies) -Black everywhere else (except - see below) -Retain the chrome around/behind turn reflectors stopping 1/2 way from back (back,side,top,bottom chrome) back half, black in front of that all around -Paint the CF top portion black Can you post what rate you would charge for a cut/paint/assemble/ship job?
__________________
CO>CA Cartel
|
|
The Following User Says Thank You to Norkoastal For This Useful Post: | poorsche (11-20-2014) |
|
|
Tags |
housing, lights, oem, retrofit, tails |
Thread Tools | Search this Thread |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Trade: Black Spyder V1 Tails for Tom's Tails | Cross | Exterior Parts (Aero, Lighting, Etc.) | 3 | 07-05-2014 04:19 PM |
Painting tails red. Is it worth wet-sanding/clear coating? | nodeal | Cosmetic Modification (Interior/Exterior/Lighting) | 25 | 04-01-2014 05:17 PM |
Autobody Shop/Painting Near Me ? Issue with Painting Carbon Fiber Hood? | ScionFR-S | Cosmetic Modification (Interior/Exterior/Lighting) | 20 | 11-08-2013 01:51 PM |
Painting the inside of the FR-S | DealerFR-S | Cosmetic Modification (Interior/Exterior/Lighting) | 21 | 07-10-2013 11:29 PM |
WTT: MY USDM Tails for your JDM/ADM/UKDM Tails | ZC6BRZ | Exterior Parts (Aero, Lighting, Etc.) | 2 | 01-16-2013 11:24 AM |