|
Software Tuning Discuss all software tuning topics. |
|
Thread Tools | Search this Thread |
09-14-2015, 02:28 PM | #1 |
Senior Member
Join Date: Jan 2015
Drives: 2013 BRZ Limited White
Location: San Antonio
Posts: 356
Thanks: 91
Thanked 192 Times in 100 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Need help disabling high rev cold start with OFT
Is there a DIY or canned tune for disabling the high rev cold start? I think this car has given me a nasty case of ringing in the ears (tinnitus). I have always had a very vague ringing, but it was so low volume that I never gave it a second thought. Ever since I installed OFH and Perrin 2.5" it seems to have gotten worse. Now it's to the point where I feel like my head is going to explode when I'm sitting alone in a quiet room.
The only thing I can think that would cause this is the car. I think it's the header and exhaust, combined with the amplifying effect of starting it in the garage. It doesn't actually cause me any pain or anything, but it literally shakes the entire house during the high rev cold start. Light fixtures on both floors rattle like crazy until the revs drop. When I start it up in the outdoor parking lot at work, it doesn't seem that bad. Either have to get rid of this cold start, or put the stock parts back on. I'd rather eliminate the cold start because I don't want to deal with effort or expense of reinstalling the stock parts, plus I don't really want to give up the extra power. Right now I'm running a canned E85 UEL OFT tune. The high rev cold start lasts about 50 seconds. For the time being, I'm just wearing shooting range ear protection when I start it up. I really hope I haven't permanently damaged my ears.. the ringing is unbearable and there's no cure and not much for treatment, as far as I can tell. |
09-14-2015, 02:42 PM | #2 |
Senior Member
Join Date: Jan 2015
Drives: 2013 BRZ Limited White
Location: San Antonio
Posts: 356
Thanks: 91
Thanked 192 Times in 100 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Ok, I just found this after digging through another thread on the topic:
1. download romraider software from the link provided on downloads page. 2. download thr romraider definitions 3. on romraider site read the how to use romraider info 4. open your tune file in romraider 5. alter required tables, dont alter anything that you dont understand 6. save modified tune file 7. load modified tune file to your OFT 8. FLASH modified tune to car 9. enjoy, drink beer I guess I'll give it a shot.. though being a novice, I don't know if this will be specific enough for me. Was hoping for a step by step diy with screenshots, if that exists anywhere. I can probably figure it out I guess. |
09-14-2015, 04:00 PM | #4 |
Senior Member
Join Date: Nov 2012
Drives: Toyota GT86
Location: Belgium
Posts: 452
Thanks: 88
Thanked 386 Times in 183 Posts
Mentioned: 4 Post(s)
Tagged: 1 Thread(s)
|
Very old screenshot (almost a year old) but it shows what needs to be changed:
__________________
"Oversteer is when your ass hits the wall, Understeer is when your face hits the wall!" - Unknown Stockcar driver
BeNeLux FB group: GT86/BRZ Owners |
09-14-2015, 04:08 PM | #5 |
Senior Member
Join Date: Jan 2015
Drives: 2013 BRZ Limited White
Location: San Antonio
Posts: 356
Thanks: 91
Thanked 192 Times in 100 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Thanks elBarto, thanks Boxxy
|
The Following User Says Thank You to MikeM7 For This Useful Post: | jawn (09-14-2015) |
09-14-2015, 04:12 PM | #6 |
Senior Member
Join Date: Nov 2012
Drives: Toyota GT86
Location: Belgium
Posts: 452
Thanks: 88
Thanked 386 Times in 183 Posts
Mentioned: 4 Post(s)
Tagged: 1 Thread(s)
|
This is a (very) quick How-to I created for the Dutch GT86/BRZ community.
I translated it very quickly for you. Just use the parts you need. Steve99 has also some nice topics about this. RomRaider (RR) - Start RomRaider, it will tell that there are no definitions configuered, ignore this. - We are going to add the OFT one for the correct callId * Go to ECU defintion manager * add the correct definition for your calid (something like OFT_ZA1JB01C.xml) press 'Apply' and 'Save' * Open the rom You will see this: Ignore it, it's normal with OFT roms Edit the necessary tables to your liking. (my example is the Launch Control) Now we are going to save it, press on the harddrive icon and give it a name (ex: stg2_UEL_Cold_start.bin) Open OpenFlash Manager, upload it to the OFT and flash the car.
__________________
"Oversteer is when your ass hits the wall, Understeer is when your face hits the wall!" - Unknown Stockcar driver
BeNeLux FB group: GT86/BRZ Owners |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Disable high Rev cold start | Raven604 | Engine, Exhaust, Transmission | 408 | 03-28-2022 10:27 AM |
Cold start | JG | Engine, Exhaust, Transmission | 8 | 08-29-2015 02:55 AM |
Cold start question | ggiddix | Engine, Exhaust, Transmission | 8 | 02-06-2015 10:27 PM |
E85 cold start | Turdinator | Software Tuning | 8 | 08-29-2014 11:12 AM |
White Smoke cold start up in Cold Weather (turbo cars) | whitefrs | Forced Induction | 17 | 09-25-2013 05:05 PM |