Afr Bung Placement for Gauge - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Saskatuon · 12-05-2021, 12:55 AM

I am looking to run a wideband AFR gauge but im not exactly sure where i should weld the bung, i have a borla uel header, invidia overpipe and front pipe. i will be retaining both my existing sensors. Any help/pics are greatly appreciated! Thanks!

Ashikabi · 12-05-2021, 01:07 AM

Holley claims the best place for wideband sensors is as close to 18"from the collector as possible. Obviously that's not where the stock front one is, so I'd say anywhere in the header rearward of the stock front o2

Sent from my ONEPLUS A5010 using Tapatalk

whataboutbob · 12-05-2021, 02:42 AM

After the merge collector if you want to see the combined AFR from all cylinders.

Saskatuon · 12-05-2021, 02:56 AM

Quote:

Originally Posted by whataboutbob

After the merge collector if you want to see the combined AFR from all cylinders.

i was thinking of this but there is really no room on the header itself with the rear 02 taking up most of the space. would the front of the front pipe be a good option? i haven't been under to see if it would have clearance yet.

whataboutbob · 12-05-2021, 03:09 AM

Quote:

Originally Posted by Saskatuon

i was thinking of this but there is really no room on the header itself with the rear 02 taking up most of the space. would the front of the front pipe be a good option? i haven't been under to see if it would have clearance yet.

I've also put a bung there. As long as you don't have a gasket leak between the output flange on the header and the input flange on the front pipe I think on the front pipe before any cats would also work. You may need to orient the bung so that when the sensor is installed that you don't have a space conflict between the installed sensor and the firewall when the front pipe is bolted up.

Grady · 12-05-2021, 07:17 PM

Front pipe is a good place for one.

12-05-2021, 12:55 AM	#1
Saskatuon Junior Member Join Date: Sep 2016 Drives: 2017 Brz Location: washington Posts: 7 Thanks: 0 Thanked 0 Times in 0 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	Afr Bung Placement for Gauge I am looking to run a wideband AFR gauge but im not exactly sure where i should weld the bung, i have a borla uel header, invidia overpipe and front pipe. i will be retaining both my existing sensors. Any help/pics are greatly appreciated! Thanks!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Afr bung on overpipe	sroby	Engine, Exhaust, Transmission	11	03-28-2017 10:46 PM
02 bung in front pipe	ort895	Engine, Exhaust, Transmission	5	03-28-2016 12:23 AM
A/F Wideband O2 Sensor Bung Location	FyeaFRS	Engine, Exhaust, Transmission	2	06-01-2015 09:17 AM
HELP: O2 bung on Rev Works header stripped?	btoast	Engine, Exhaust, Transmission	9	12-21-2014 06:11 AM
Aftermarket gauge placement	CyberFormula	Scion FR-S / Toyota 86 GT86 General Forum	22	08-18-2012 01:01 AM

12-05-2021, 01:07 AM	#2
Ashikabi Senior Member Join Date: Aug 2014 Drives: 2013 FR-S Location: Northwest Iowa Posts: 7,354 Thanks: 454 Thanked 4,542 Times in 2,947 Posts Mentioned: 59 Post(s) Tagged: 5 Thread(s)	Holley claims the best place for wideband sensors is as close to 18"from the collector as possible. Obviously that's not where the stock front one is, so I'd say anywhere in the header rearward of the stock front o2 Sent from my ONEPLUS A5010 using Tapatalk

User Name		Remember Me?
Password