03-03-2019, 04:44 AM | #1 |
Member
Join Date: Feb 2019
Drives: 1800whp gt86
Location: dubai
Posts: 10
Thanks: 0
Thanked 26 Times in 8 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
a gt86 @ 1800whp LSX
Hey everyone ,( my English is not good)
This is my first thread on this forum and sorry to start very hard So we launched project to reach 1800whp on GT86 and will need your full support to reach that the best we I can, I will write all detail I have and remained me if I forget something So I will start by Engine: 427 LSX block 1. Callies ultra billet connecting rod 2. Callies crank 3. Diamond piston Mast heads Shaun billet intake ECU: ( I will need to vote ) 1. MoteC M150( with c1212 dash ) 2. Fueltech FT600 Fuel system: Dual injectors system 1. Primary 1800cc ID 2. Secondary Atomizer 7500cc to support the car to run on full methanol Fuel pumps 1. triple DW in tank 415lb fuel pump 2. mechanical fuel pump for secondary system fuel tanks 1. main tank for pump gas 2. anodized secondary tank for methanol fuel regulator 1. 2000HP DW for primary 2. 3000hp DW for secondary Turbo kit and exhaust : Twin 74mm turbos Twin 40mm wastage 3.5 inch down pipe to the finder and 3 inch to the back Twin Water to air cooler intercooler Water reservoir Drive train : Transmission 1. PPG Sequential TR6060 2. Quad plate clutch ?? what brand to use ??? Drive shaft 3. Custom by driveshaft shop Rear end o Here where I need your advice >> what can handle 1800whp???? Roll cage: 10 point with chassis support ( is there anything ready or should I do it at the shop ?) Front bar for radiator mount Back wi need to some bracket for diff and suspension Please let me know If I forget something and will answer all of you back |
03-03-2019, 09:40 AM | #2 |
Senior Member
Join Date: Oct 2016
Drives: 2017 WR BLUE BRZ
Location: San Jose
Posts: 641
Thanks: 608
Thanked 502 Times in 249 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
|
For 1800 hp, I’d probably start looking at a 9”. Drive shaft shop may be able to help if you don’t want to dab it yourself. http://www.driveshaftshop.com/kit-ca...manual-6-speed
Wheel hubs and suspension needs to be addressed too. Should be fun! |
03-03-2019, 11:46 AM | #4 |
Member
Join Date: Dec 2017
Drives: jrsc_brz
Location: boston
Posts: 966
Thanks: 726
Thanked 675 Times in 336 Posts
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
|
This is the best 1st post in the history of time
|
The Following User Says Thank You to HaXx For This Useful Post: | EAGLE5 (03-03-2019) |
03-03-2019, 12:13 PM | #6 |
Senior Member
Join Date: Sep 2015
Drives: 2016 Halo FRS
Location: US
Posts: 414
Thanks: 290
Thanked 161 Times in 106 Posts
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
|
Dudes from Dubai. Yall laughing, guy wipes his ass with 100s lol
|
The Following 3 Users Say Thank You to Trust86 For This Useful Post: |
03-03-2019, 12:26 PM | #7 |
Wes
Join Date: Feb 2017
Drives: Artisan Spirits '17 86
Location: Toronto
Posts: 2,792
Thanks: 1,163
Thanked 1,673 Times in 993 Posts
Mentioned: 21 Post(s)
Tagged: 0 Thread(s)
|
This is probably his 10th side hobby project lol, something to do on tuesday evenings
__________________
Instagram: @gt86ws
|
03-03-2019, 01:39 PM | #8 |
Dismember
Join Date: Mar 2013
Drives: 2013 Red Scion FR-S
Location: Castro Valley
Posts: 5,557
Thanks: 2,152
Thanked 3,999 Times in 2,155 Posts
Mentioned: 43 Post(s)
Tagged: 1 Thread(s)
|
If you're at all serious, you should contact a shop in the US that does this on a regular basis. You can order a 2000HP LSX all put together for you by somebody who knows what they're doing. Or you can put it together yourself and watch it blow up a few times until you figure out how to do things right. Any car that makes this much power should have little or nothing to do with the original car.
__________________
|
03-03-2019, 01:40 PM | #9 |
Senior Member
Join Date: Jul 2014
Drives: 2020 Hakone
Location: London, Ont
Posts: 69,845
Thanks: 61,656
Thanked 108,283 Times in 46,456 Posts
Mentioned: 2494 Post(s)
Tagged: 50 Thread(s)
|
Fictional shopping list from internet is fictional.
__________________
Racecar spelled backwards is Racecar, because Racecar.
|
03-03-2019, 02:04 PM | #10 |
Senior Member
Join Date: Jul 2014
Drives: 14 BSP Edelbrock BRZ
Location: Lon Gisland
Posts: 806
Thanks: 113
Thanked 450 Times in 256 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
This is going to be such an insane task you are better off with a tube frame and then dropping the body on top of it if you like the looks of a BRZ. 1800 hp will give you a better power to weight ratio than a Konigsegg One:1. Whatever you do for a rear end better be narrow, you're going to need 20" wide tires to have any traction.
|
03-03-2019, 02:26 PM | #11 |
Weight Weenie
Join Date: Aug 2015
Drives: 15 FR-S
Location: Canada
Posts: 2,584
Thanks: 5,007
Thanked 2,330 Times in 1,346 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
I did something similar in a weekend. It's pretty simples
|
03-03-2019, 09:17 PM | #12 |
Senior Member
Join Date: Mar 2017
Drives: Q5 + BRZ + M796
Location: Santa Rosa, CA
Posts: 7,882
Thanks: 5,665
Thanked 5,802 Times in 3,297 Posts
Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
|
I’m a little confused by all you guys. The guy is in Dubai. Do you guys have any clue what they are doing over there? There are lots of people with deep pockets.
Meanwhile in Dubai... [ame]https://m.youtube.com/watch?v=tA8ElgCit1A[/ame] Maybe consider a billet block like this Alpha car, but if they can reach 2000hp with almost half the displacement then it is doable. [ame]https://m.youtube.com/watch?v=35Ah6yNMGK4[/ame] https://www.amsperformance.com/project/alpha-omega-gtr/
__________________
My Build | K24 Turbo Swap | *K24T BRZ SOLD*
Last edited by Irace86.2.0; 03-04-2019 at 01:15 AM. |
03-04-2019, 08:20 AM | #13 |
Senior Member
Join Date: Mar 2013
Drives: 2JZ FRS
Location: Pure Automotive Performance
Posts: 1,378
Thanks: 97
Thanked 1,354 Times in 621 Posts
Mentioned: 27 Post(s)
Tagged: 2 Thread(s)
|
probably going to need more than 74mm's, that trans is going to be questionable, and our custom 9" with axles/hubs is barely enough to hold our 2j (axle/hub wise) , let alone the torque that v8 would make. Id do a solid rear axle and 4 link. Fueltech would be fine for a car like that since i doubt you would be integrating many oem features lol. Im liking the build sheet though, looks awesome
__________________
|
The Following User Says Thank You to spitfire481 For This Useful Post: | Sportsguy83 (03-04-2019) |
03-04-2019, 09:58 AM | #14 |
Member
Join Date: Feb 2019
Drives: 1800whp gt86
Location: dubai
Posts: 10
Thanks: 0
Thanked 26 Times in 8 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
So let us see i just recived my block and head.. A small mistake.. The heads are Dart
|
|
|
Thread Tools | Search this Thread |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
EVERYTHING TRD FRS/GT86 | imravenit | BRZ Photos, Videos, Wallpapers, Gallery Forum | 3 | 10-27-2014 12:11 PM |
H6 GT86 | radroach | Scion FR-S / Toyota 86 GT86 General Forum | 12 | 11-20-2013 03:37 PM |
WRC Car: TMG GT86 CS-R3 | riyal | AFRICA | 8 | 11-19-2013 02:03 PM |
GT86 OEM Option Pin Stripes (anyone done this to their 86/GT86/FRS/BRZ)??? | jbsali | Cosmetic Modification (Interior/Exterior/Lighting) | 27 | 07-28-2013 11:10 PM |
MEETING 'MR GT86' - Tada San drives GT86 in Scotland (Pistonheads) | RadOnc | Scion FR-S / Toyota 86 GT86 General Forum | 15 | 11-23-2012 08:42 AM |