FT-86 SpeedFactory - V1 Cat Back Exhaust - Your feedback wanted! - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

FT-86 SpeedFactory · 09-04-2012, 12:21 AM

FT-86 Speed Factory has been working on this exhaust for a couple weeks now. We have got this version to a beta test stage and have been driving around with it for the last week. We will be racing with it at the SCCA Solo Nationals this week and then take it into production.

We set out to build this version to be the exhaust that won't annoy the girlfriend or yourself, won't attract attention from the police, and frankly be something that can be used in a daily driver / weekend warrior car. You hear the exhaust when you want to, by letting the RPM's wrap out with your foot firmly on the floor, and don't hear it when cruising at 3000 RPM down the highway. It is also not overly loud when shifting normally on your morning commute to work. To keep the ruckus down during normal driving we had to use a heavier muffler. Testing showed us that the lighter mufflers increased noise in the RPM ranges for daily commutes and is not something we wanted in our V1 system. We will have lighter exhausts for our V2 and V3 due out later this year. The number one goal for the V1 is sound and daily drive-ability, and I firmly believe that has been accomplished here.

V1 BETA SPECS:
2.5" T304 Stainless Catback to Mufler
Minimal bends, as straight as possible
3.5" Stainless Angle Cut tips ( possible 4" on finial version you help decide )
Made in the U.S.A
V-Band Clamp for rear section
Up to a 7 Wheel HP Gain in the RPM range
Up to a 3 FT LB in Torque Gain in the RPM range
Doesn't annoy the Girlfriend / Wife

We are looking for your feedback to help make this exhaust one of the best out there for a daily driver / weekend warrior.

Pics

Videos

Start up and rev from exterior
[ame="http://www.youtube.com/watch?v=nhjkOvByLSI"]FT-86 Speed Factory V1 Exhaust - YouTube[/ame]

Drive by from exterior
[ame="http://www.youtube.com/watch?v=4175rHkAkAs"]FT-86 Speed Factory V1 Exhaust - Drive By - YouTube[/ame]

Interior video of launch and full throttle
[ame="http://www.youtube.com/watch?v=wmcj_SqTGmw"]FT-86 Speed Factory Catback Exhaust V1 - Launch - YouTube[/ame]

Interior video of normal driving conditions
[ame="http://www.youtube.com/watch?v=d7EAYQDPYDE"]FT-86 Speed Factory V1 Exhaust - Inside Driving - YouTube[/ame]

Dyno Video ( 4th gear )
[ame="http://www.youtube.com/watch?v=h8munnC0YHs"]FT - 86 SpeedFactory Scion FR-S dyno of our V1 exhaust - YouTube[/ame]

Dyno Chart ( 4th gear )

Lee358 · 09-04-2012, 12:27 AM

hm not to bad guys i think for what it is it sounds like a good solution cant wait to see your lighter louder v2 and v3 see if you can bump that 7hp up a bit.. also 4in tips

WolfsFang · 09-04-2012, 12:46 AM

this sounds amazing, i think this is an amazing exhaust for DD for the avg person. Now i hope your V2 or V3 will just be straight with no big muffler like the SRT end (if that makes sense)

Lee358 · 09-04-2012, 12:51 AM

ohh! almost forgot Price Matters!

brichard0625 · 09-04-2012, 02:30 AM

hmmm....i like it...and 4inch tips

FT-86 SpeedFactory · 09-04-2012, 08:46 AM

I must be getting old. I thought the 3.5" were pretty solid.

We'll get some photos up with 4" tips ASAP.

JoeBoxer · 09-04-2012, 09:11 AM

4" for sure but otherwise looks good.

brichard0625 · 09-04-2012, 09:24 AM

Quote:

Originally Posted by FT-86 SpeedFactory

I must be getting old. I thought the 3.5" were pretty solid.

We'll get some photos up with 4" tips ASAP.

3.5 still looks good but i think it looks a little more aggressive when the exhaust gaps are filled up a little more.

ngabdala · 09-04-2012, 09:26 AM

3" piping 4" tips

drifter · 09-04-2012, 01:21 PM

was everything else stock in those videos besides the exhaust?

YoKeutla · 09-04-2012, 01:30 PM

Quote:

Originally Posted by drifter

was everything else stock in those videos besides the exhaust?

Yes, stock baseline then nothing but the cat-back was installed.

Car has approximately 2500 miles, I believe.

EDIT: Not sure on all the videos! Just the Dyno. There may have been a drop-in filter installed on the other videos. I will let JB respond to that.

RE-EDIT: Just asked JB and the car was in-fact all stock minus the cat-back exhaust.

ATL BRZ · 09-04-2012, 01:45 PM

Really like the sound of this one!! Looking forward to pricing and I'm voting for 4" tips please!!

Hotlava86 · 09-04-2012, 02:44 PM

Jeremy! i want mine! i'll test it for you and post an AWESOME review!

JSK · 09-04-2012, 06:58 PM

They said it is a "heavier muffler" compared to other systems but does anyone know the actual weight or how it compares to stock?

09-04-2012, 12:21 AM	#1
FT-86 SpeedFactory Join Date: Jul 2012 Drives: 2013 Scion FR-S Location: Des Moines, IA Posts: 7,694 Thanks: 1,298 Thanked 3,578 Times in 1,253 Posts Mentioned: 341 Post(s) Tagged: 5 Thread(s)	FT-86 SpeedFactory - V1 Cat Back Exhaust - Your feedback wanted! FT-86 Speed Factory has been working on this exhaust for a couple weeks now. We have got this version to a beta test stage and have been driving around with it for the last week. We will be racing with it at the SCCA Solo Nationals this week and then take it into production. We set out to build this version to be the exhaust that won't annoy the girlfriend or yourself, won't attract attention from the police, and frankly be something that can be used in a daily driver / weekend warrior car. You hear the exhaust when you want to, by letting the RPM's wrap out with your foot firmly on the floor, and don't hear it when cruising at 3000 RPM down the highway. It is also not overly loud when shifting normally on your morning commute to work. To keep the ruckus down during normal driving we had to use a heavier muffler. Testing showed us that the lighter mufflers increased noise in the RPM ranges for daily commutes and is not something we wanted in our V1 system. We will have lighter exhausts for our V2 and V3 due out later this year. The number one goal for the V1 is sound and daily drive-ability, and I firmly believe that has been accomplished here. V1 BETA SPECS: 2.5" T304 Stainless Catback to Mufler Minimal bends, as straight as possible 3.5" Stainless Angle Cut tips ( possible 4" on finial version you help decide ) Made in the U.S.A V-Band Clamp for rear section Up to a 7 Wheel HP Gain in the RPM range Up to a 3 FT LB in Torque Gain in the RPM range Doesn't annoy the Girlfriend / Wife We are looking for your feedback to help make this exhaust one of the best out there for a daily driver / weekend warrior. Pics Videos Start up and rev from exterior [ame="http://www.youtube.com/watch?v=nhjkOvByLSI"]FT-86 Speed Factory V1 Exhaust - YouTube[/ame] Drive by from exterior [ame="http://www.youtube.com/watch?v=4175rHkAkAs"]FT-86 Speed Factory V1 Exhaust - Drive By - YouTube[/ame] Interior video of launch and full throttle [ame="http://www.youtube.com/watch?v=wmcj_SqTGmw"]FT-86 Speed Factory Catback Exhaust V1 - Launch - YouTube[/ame] Interior video of normal driving conditions [ame="http://www.youtube.com/watch?v=d7EAYQDPYDE"]FT-86 Speed Factory V1 Exhaust - Inside Driving - YouTube[/ame] Dyno Video ( 4th gear ) [ame="http://www.youtube.com/watch?v=h8munnC0YHs"]FT - 86 SpeedFactory Scion FR-S dyno of our V1 exhaust - YouTube[/ame] Dyno Chart ( 4th gear )

09-04-2012, 12:46 AM	#3
WolfsFang Scrape Master Join Date: Jun 2012 Drives: Goal: Oldest FRS State Side Location: North NJ Posts: 1,161 Thanks: 238 Thanked 412 Times in 238 Posts Mentioned: 10 Post(s) Tagged: 0 Thread(s)	this sounds amazing, i think this is an amazing exhaust for DD for the avg person. Now i hope your V2 or V3 will just be straight with no big muffler like the SRT end (if that makes sense) __________________ You do realize comparing the BRZ to the FR-S is like comparing which hand you love masterbating too right?

09-04-2012, 02:30 AM	#5
brichard0625 Senior Member Join Date: Jun 2012 Drives: 2013 Scion Frs(Scarlet) Location: Bronx, NY Posts: 907 Thanks: 172 Thanked 386 Times in 177 Posts Mentioned: 4 Post(s) Tagged: 0 Thread(s)	hmmm....i like it...and 4inch tips __________________

09-04-2012, 09:26 AM	#9
ngabdala Vortech Supercharged Join Date: Apr 2012 Drives: WRB BRZ 6MT LTD Location: Massachusetts Posts: 1,447 Thanks: 1,897 Thanked 467 Times in 283 Posts Mentioned: 13 Post(s) Tagged: 1 Thread(s)	3" piping 4" tips __________________ Powered by Vortech, ECS Tuning, and JDL Auto Design

09-04-2012, 02:44 PM	#13
Hotlava86 Senior Member Join Date: Jul 2012 Drives: 2013 Hot lava Fr-s, 2007 Mazda 3 Location: kansas city missouri Posts: 282 Thanks: 30 Thanked 60 Times in 41 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	Jeremy! i want mine! i'll test it for you and post an AWESOME review! __________________ Raising the bar one step at a time! Kansas City FR-S/BRZ Facebook group. https://www.facebook.com/groups/452909128083343/ Hotlava86's Build thread!http://www.ft86club.com/forums/showthread.php?t=14152

09-04-2012, 12:27 AM	#2
Lee358 Senior Member Join Date: Jun 2012 Drives: nissan frontier, DGM MT BRZ Location: North nj Posts: 1,576 Thanks: 404 Thanked 418 Times in 254 Posts Mentioned: 7 Post(s) Tagged: 0 Thread(s)	hm not to bad guys i think for what it is it sounds like a good solution cant wait to see your lighter louder v2 and v3 see if you can bump that 7hp up a bit.. also 4in tips

09-04-2012, 12:51 AM	#4
Lee358 Senior Member Join Date: Jun 2012 Drives: nissan frontier, DGM MT BRZ Location: North nj Posts: 1,576 Thanks: 404 Thanked 418 Times in 254 Posts Mentioned: 7 Post(s) Tagged: 0 Thread(s)	ohh! almost forgot Price Matters!

09-04-2012, 08:46 AM	#6
FT-86 SpeedFactory Join Date: Jul 2012 Drives: 2013 Scion FR-S Location: Des Moines, IA Posts: 7,694 Thanks: 1,298 Thanked 3,578 Times in 1,253 Posts Mentioned: 341 Post(s) Tagged: 5 Thread(s)	I must be getting old. I thought the 3.5" were pretty solid. We'll get some photos up with 4" tips ASAP.

09-04-2012, 09:11 AM	#7
JoeBoxer Senior Member Join Date: Jul 2012 Drives: Whiteout FR-S Location: Arkansas Posts: 4,154 Thanks: 1,666 Thanked 1,627 Times in 997 Posts Mentioned: 72 Post(s) Tagged: 0 Thread(s)	4" for sure but otherwise looks good.

09-04-2012, 01:21 PM	#10
drifter Senior Member Join Date: Jun 2012 Drives: truck and old car Location: CA Posts: 295 Thanks: 120 Thanked 168 Times in 66 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	was everything else stock in those videos besides the exhaust?

09-04-2012, 01:45 PM	#12
ATL BRZ Driving Coach Join Date: Jun 2012 Drives: BRZ Location: Atlanta Posts: 3,666 Thanks: 3,723 Thanked 4,136 Times in 1,707 Posts Mentioned: 90 Post(s) Tagged: 6 Thread(s)	Really like the sound of this one!! Looking forward to pricing and I'm voting for 4" tips please!!

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
SRT header back exhaust brand new	scioneric	Engine, Exhaust, Bolt-Ons	5	09-19-2012 11:10 AM
Nice cat-back exhaust!	Chad	FR-S & 86 Photos, Videos, Wallpapers, Gallery Forum	11	08-29-2012 02:55 PM
Custom Axle back Exhaust	Do Boy	Engine, Exhaust, Transmission	13	08-19-2012 07:54 AM

User Name		Remember Me?
Password