Tripjammer's WRB BRZ Limited

[tripjammer]

[ame]http://youtu.be/yVa5x1FNBbA[/ame]

After months waiting for a whiteout FR-S, I can across a BRZ limited in transit to a dealer in Denver, Colorado. I jumped on it and got an awesome deal. Had it delivered to my house in San Antonio. Diamond Express Delivery is top notch in their services.

Current mods:

Exterior
Perrin Shorty Antennae
Perrin Exhaust Tips
LED's fog Lights
LED's turn signals
LED's in clear corners
LED's in rear side marker lights
LED's in backup lights
JDM clear front side markers
Suntek Clear film on front bumper and lower rear bumper
Suntek Clear film on full hood
Suntek Carbon XP window tint
Optiguard Pro after complete polish and paint correction
Rexspeed Convex Mirrors





Interior
JPM Coachworks Alcantara instrument cover
JDM red STI start button
Weathertech front floor liners
LED's in door panels
LED's in sun visors
LED bulb in trunk light
LED bulb in map light
Weathertech trunk liner




Under the Hood
Dynotronics 93 Octane Ecutek tune
Perrin battery tie down
Perrin oil cap
Grimmspeed hood struts
TRD CAI
Perrin master cylinder brace (ordered)
Greddy radiator cap (ordered)

[tripjammer]

It's got 8 miles!








Real Dirty!




Jay you need to do your magic!


Ah, a little better.




At least the engine was clean...LOL!

[tripjammer]

At Jaysdetail getting much needed magic!


Magic I tell you!


Got3n molesting her tips....LOL!


Jay @ JaysDetailing finishing up the Optiguard. It's cure time!

[L3P47]

Welcome to the community man!

[tripjammer]

BRZ Parts Phase 1











The BRZ actually uses 7440 front and rear for the turn signals. They sent me 7443 for the front and 7440 for the rear.

[Subaruwrxfan]

Congrats man! Enjoy it!

[tripjammer]

Dammit I lost an LED bulb into the rear housing. Anybody know how to get it out?

[kwood9000]

Originally Posted by tripjammer

Dammit I lost an LED bulb into the rear housing. Anybody know how to get it out?

Maybe a vacuum cleaner or telescoping magnet might help.

By the way, if you think those reverse led lights are too dim, try some 360 degree type LEDs instead.

[tripjammer]

Originally Posted by kwood9000

Maybe a vacuum cleaner or telescoping magnet might help.

By the way, if you think those reverse led lights are too dim, try some 360 degree type LEDs instead.

Ohhhh, A telescoping magnet! Yeah!!!

[tripjammer]

The Red STI start button came in. I just have to install it....








Painters Tape is your friend!


Done! This was the easiest mod to do.

I followed these directions:

Pop the passenger side center stack lower cover (below the knee pad) off. Reach in from behind and pop the USB connector out (push forward). The next step is to unplug the connection and push the wiring back through the exposed hole. After that reach into the now vacant USB hole with your pointer finger and pull gently. It may require some tugging a bit, but it will eventually pop out. Just go slow and use some Painters tape to cover the area in front of the shifter.

Thanks Bugeyedwagon!

[subiestar]

Very nice first mods. I'd like to see pics of the fog LEDs.

[tripjammer]

Originally Posted by subiestar

Very nice first mods. I'd like to see pics of the fog LEDs.

I am waiting for my clear corners to come in before I do the LED fogs, so I can do them both at the same time. Already got amber LEDs for the clear corners too. I found that there is one more regular bulb in the rear tail lights, rear side marker light. I will replace that with an LED too.

Yeah my hands need some lotion.

[tripjammer]

I got the rear CREE led backup light removed from the left housing after it fell in earlier this week.


I used this...a telescoping screw driver with a magnet on it. Went to my mums house and she had one, and it worked! It pulled right out very easily.


Bright CREE LED Backup lights.

[tripjammer]

I tried to install my Grimspeed gas hood struts, but I gave up. I could not get those black screws to go in. I did not want to strip it.