12-18-2013, 12:26 PM | #1 |
Senior Member
|
MoTeC FT86
MoTeC is happy to announce the release of an M1 Package for the Toyota 86 2012 FA20D. Currently compatible with the Manual Transmission versions of the following vehicles: Toyota 86, Subaru BRZ and Scion FR-S models from 2012 onward. A licensed Toyota 86 2012 FA20D Package together with an activated M150 ECU and optional loom, combines to become a fully programmable replacement for the factory-fitted Toyota 86 ECU. No rewiring is necessary with the optional loom, which plugs into the stock wiring harness using the original sensors and fuel system. All original functions are maintained Works with all of the stock componentry, including: Power steering ABS Stability control Air conditioner Dashboard Adds powerful extra capabilities, including: Turbo or supercharger control Launch control Traction control Gear Shift ignition cutting • Pre-configured physical settings for Engine Displacement, Fuel Density, Stoichiometric Ratio, Fuel Pressure, and Injector Linearisation, which allow for simplified engine start-up prior to tuning. • Pre-configured control of OE coolant fans with 3 temperature • Fully integrates with these original systems: Direct Injection, thresholds. Stability, Dash, Power Steering, ABS, Air Conditioner, Purge • Pre-configured transient fuelling compensation using physical Canister, and Alternator control. Cruise Control is not supported. Lambda Control is supported with optional LTC and Bosch LSU4.9 Sensor. • Pre-configured wheel speed detection via CAN from OE ABS system, allowing gear detection via engine speed / wheel speed estimate. • Pre-configured sensor calibrations for Original Equipment (OE) speed estimate. sensors and engine triggers. • Gearbox position detection via optional sensor. • Pre-configured control of port and direct injectors with a tunable balance table. • Configurable boost control for a single turbo. • Pre-configured reference mode for engine synchronization and • Configurable anti-lag for single turbo with Ignition Timing Limit, control of 4 camshafts with tunable inlet and exhaust timing Fuel Volume Trim, Ignition Cut, Engine Speed Limit, Boost Aim tables. and Throttle Aim tables. • Pre-configured on-board knock control for each cylinder with 2 • Gearbox shift request via Up Shift Switch / Down Shift Switch OE knock sensors and selectable center frequency. or Gear Lever Force sensor. Contact me for more info Sean@Titanmotorsports.com |
12-18-2013, 02:14 PM | #2 |
Banned
|
Very Nice
|
12-18-2013, 03:51 PM | #3 |
Senior Member
Join Date: Nov 2011
Drives: car
Location: cold
Posts: 599
Thanks: 72
Thanked 607 Times in 185 Posts
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
|
Can you explain how the DI + Port fuel mapping and control logic works? On the most basic level: is it pulsewidth and fuel pressure lookup tables? Or does it calculate a fuel quantity and then figure out what injection is needed to get there?
How is the DI injector flow characterized with regard to pulsewidth and fuel pressure? How much tuning is going to be needed to get the high pressure fuel pump to control fuel setpoint accurately? Does the system support multiple DI injections? How is the split between the two injections controlled and the start of injection? How does that relate to the port injection control? How is the tip-in acceleration fuel handled in both port and DI injection modes? |
The Following User Says Thank You to arghx7 For This Useful Post: | SkullWorks (12-18-2013) |
12-18-2013, 05:44 PM | #4 | |
Senior Member
|
Quote:
As mentioned please contact Sean@titanmotorsports.com |
|
12-18-2013, 06:04 PM | #5 | |
Banned
Join Date: Mar 2012
Drives: SSM LT MT BRZ
Location: SoCal
Posts: 1,033
Thanks: 803
Thanked 754 Times in 328 Posts
Mentioned: 23 Post(s)
Tagged: 1 Thread(s)
|
Quote:
Would it be too mch to ask that you simply make the info (as you understand it) public knowledge? It is information that would benefit more than the person asking the question. |
|
12-18-2013, 06:14 PM | #6 | |
Senior Member
|
Quote:
I will try to have him respond on the forum, but he works mainly with emails. |
|
02-25-2021, 02:24 AM | #7 |
Member
Join Date: Jul 2013
Drives:
Posts: 96
Thanks: 8
Thanked 7 Times in 7 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
i also bought this product from TItan..
recommended ECU also recommended Seller |
02-25-2021, 02:11 PM | #8 |
Senior Member
Join Date: Aug 2018
Drives: turbo frs
Location: worldwide
Posts: 173
Thanks: 122
Thanked 8 Times in 7 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
5570$ Just fo motec
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
FT86 vs. RX-7 FD | FutureFT86 | FR-S / BRZ vs.... | 148 | 01-05-2020 09:48 PM |
Evasive FT86 Service & Maintenance Thread Discount Labor for FT86 Members | Evasive Motorsports | Southern California | 423 | 10-01-2018 12:49 PM |
Motec M1 Plug N Play | FullBlown | Forced Induction | 89 | 05-09-2014 12:45 PM |
FT86 new look | Kimsey47 | Site Announcements / Questions / Issues | 5 | 11-19-2013 09:36 PM |
What do you like other than the FT86??? | Coconut | Off-Topic Lounge [WARNING: NO POLITICS] | 59 | 04-15-2011 02:23 PM |