07-30-2018, 07:34 PM | #29 |
Senior Member
Join Date: Sep 2015
Drives: 2015 frs
Location: Ca
Posts: 511
Thanks: 426
Thanked 196 Times in 148 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
Dry sump
Dry sump arrived
|
The Following 3 Users Say Thank You to Zer0 For This Useful Post: |
08-01-2018, 12:48 PM | #31 |
Senior Member
Join Date: Sep 2015
Drives: 2015 frs
Location: Ca
Posts: 511
Thanks: 426
Thanked 196 Times in 148 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
S.P.E.C super twin clutch assembly
|
The Following User Says Thank You to Zer0 For This Useful Post: | JeremyR (08-01-2018) |
08-03-2018, 03:15 PM | #32 |
Senior Member
Join Date: Sep 2015
Drives: 2015 frs
Location: Ca
Posts: 511
Thanks: 426
Thanked 196 Times in 148 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
ATI Super Damper and supercharger pulley.
|
The Following User Says Thank You to Zer0 For This Useful Post: | DustinS (08-03-2018) |
08-06-2018, 01:00 PM | #33 |
Senior Member
Join Date: Sep 2015
Drives: 2015 frs
Location: Ca
Posts: 511
Thanks: 426
Thanked 196 Times in 148 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
A few more parts arrived
|
The Following 4 Users Say Thank You to Zer0 For This Useful Post: |
08-07-2018, 08:41 PM | #35 |
Member
Join Date: May 2018
Drives: Soon
Location: Louisiana
Posts: 37
Thanks: 19
Thanked 21 Times in 16 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Following....
Curious what route you're going with trans and ECU? Sent from my SM-G965U using Tapatalk |
08-07-2018, 08:56 PM | #36 |
Senior Member
Join Date: Sep 2015
Drives: 2015 frs
Location: Ca
Posts: 511
Thanks: 426
Thanked 196 Times in 148 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
|
08-07-2018, 09:29 PM | #37 |
Senior Member
Join Date: Jul 2016
Drives: BRZ, WRX
Location: Sydney, Australia
Posts: 291
Thanks: 105
Thanked 962 Times in 233 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Nice project, subscribed.
__________________
|
The Following User Says Thank You to DIY For This Useful Post: | Zer0 (08-07-2018) |
08-11-2018, 10:24 PM | #38 |
Senior Member
Join Date: Sep 2015
Drives: 2015 frs
Location: Ca
Posts: 511
Thanks: 426
Thanked 196 Times in 148 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
The measurements on the engine side of my Vorshlag mounts won't work with a LT4. Not surprised they were designed for a LS swap. I was able to find laser cut motor side mount plates to use to make your own mounts, I also found laser cut tabs. I purchased both, and will use them to make my own engine side mounts that will hopefully work with my lower Crossmember side Vorshlag mounts. If not I will have to make that side as well. We will see how far back, and how much lower I can go with the engine
|
08-21-2018, 03:36 PM | #39 |
Member
Join Date: Aug 2016
Drives: 2015 Brz Limited
Location: New York
Posts: 34
Thanks: 7
Thanked 4 Times in 4 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Love the build so far! I don't know why but I never considered moving the heater hoses until this thread.
Will be following very closely as I plan on purchasing a wrecked camaro for its lt1 & Trans. |
The Following User Says Thank You to HawaiianMike For This Useful Post: | Zer0 (08-22-2018) |
08-22-2018, 02:47 AM | #40 |
Senior Member
Join Date: Sep 2015
Drives: 2015 frs
Location: Ca
Posts: 511
Thanks: 426
Thanked 196 Times in 148 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
Motor prep.
I removed the oil pump, replaced the plastic oil dumbbell with a aluminum machined unit, and swaped out the oil pan
|
08-22-2018, 02:53 AM | #41 |
Senior Member
Join Date: Sep 2015
Drives: 2015 frs
Location: Ca
Posts: 511
Thanks: 426
Thanked 196 Times in 148 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
Going to try to get the bell housing measurements this week, and clock it if necessary. Hopefully I get lucky, and don't need to adjust it's position.
|
08-25-2018, 09:43 PM | #42 |
Senior Member
Join Date: Sep 2015
Drives: 2015 frs
Location: Ca
Posts: 511
Thanks: 426
Thanked 196 Times in 148 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
Found out the timing chain cover, crankshaft snout length , and supercharger front snout is different from dry to wet sump engine. I bought a extra supercharger. I'm going to swap the front of the superchargers, and sell the one I bought setup for the wet sump LT1 motor with the crank pulley, oem shorty header manifolds, and coolant pump. Adapters would be needed to bolt the supercharger on to the LT1 heads, but they are available already.
Last edited by Zer0; 12-25-2018 at 07:58 PM. |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Andy0323's Back To Basics Build Thread <Long Term Project> | andy0323 | Member's Car Journals | 15 | 02-02-2018 12:16 AM |
long term and short term | brichard0625 | Engine, Exhaust, Transmission | 7 | 08-26-2013 08:56 AM |
Long term | Bt216 | Scion FR-S / Toyota 86 GT86 General Forum | 3 | 06-06-2013 11:58 PM |
Fuel Trims - Long term and short term | victorb | Engine, Exhaust, Transmission | 6 | 03-27-2013 02:18 PM |
Short Term and Long Term Fuel Trims | naikaidriver | Engine, Exhaust, Transmission | 3 | 03-18-2013 09:55 PM |