12-31-2017, 10:11 AM | #841 |
Senior Member
Join Date: Sep 2017
Drives: 2022 BRZ Limited Silver
Location: Jacksonville, FL
Posts: 2,532
Thanks: 882
Thanked 2,045 Times in 1,188 Posts
Mentioned: 68 Post(s)
Tagged: 0 Thread(s)
|
Tactrix EcuFlash Info for BRZ 86 FRS Rom flash update and logging
I just went through your config again and still didn’t see OilTemp. Turns out Tapatalk only shows the tail end of your config. I had to read your post in a web browser to see the whole thing. What CalID are you on? I see several channels I’d like to snag. Edit: never mind I see in the config it says ZA1JA01G. I’m on B01C. Darn. |
12-31-2017, 10:25 PM | #842 |
Banned
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
|
@ermax
For oil temp in your B01C use same scaling as A01G subsiture in ram address below. Ot will come out as celcius though B01C/B01D Oil temp address Ram_Engine_Oil_Temperature FFF8DC20 |
02-09-2018, 03:12 PM | #843 | |
Road-hole
Join Date: Jul 2014
Drives: 2013 Whiteout FR-S
Location: Gilbert, Arizona
Posts: 1,112
Thanks: 272
Thanked 479 Times in 292 Posts
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
|
Arduino based Boost control
Quote:
If you use an arduino based flex fuel analyzer it would be extremely easy to add a second voltage output to control boost based on e85 content. Have it run waste gate pressure at 50hz and 12psi at 135hz. I could write the code for anyone who's interested for an arduino based flex fuel and integrated boost control. Jaden |
|
02-10-2018, 01:00 PM | #844 | |
Road-hole
Join Date: Jul 2014
Drives: 2013 Whiteout FR-S
Location: Gilbert, Arizona
Posts: 1,112
Thanks: 272
Thanked 479 Times in 292 Posts
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
|
Additionally...
Quote:
It's time we started seeing and using canbus for the benefits instead of just the negatives. IOW, we don't have to be able to program everything into the engine ecu. We can start creating our own controllers for additional features. A simple algorithm that will adjust voltage output going to an electronic boost controller based on gear inputs as well. So it would be incrementally increased based on a combination of FF sensor freq and reported gear. Jaden p.s. In a way this would be even better than Ecutek's solution because you aren't limited by the number of inputs, i.e. you can keep both O2 sensors and still have flex fuel AND boost control. Last edited by Jaden; 02-10-2018 at 01:15 PM. |
|
The Following 2 Users Say Thank You to Jaden For This Useful Post: | eddieflyinv (02-10-2018), XCO (02-21-2018) |
02-28-2018, 05:09 PM | #845 |
Senior Member
Join Date: Feb 2015
Drives: Toyota GT86
Location: Europe
Posts: 919
Thanks: 369
Thanked 554 Times in 301 Posts
Mentioned: 40 Post(s)
Tagged: 2 Thread(s)
|
Can anyone help with the correct RAM address for logging AFR command on B01C?
Thanks.
__________________
|
02-28-2018, 06:29 PM | #846 |
Senior Member
Join Date: Sep 2017
Drives: 2022 BRZ Limited Silver
Location: Jacksonville, FL
Posts: 2,532
Thanks: 882
Thanked 2,045 Times in 1,188 Posts
Mentioned: 68 Post(s)
Tagged: 0 Thread(s)
|
|
02-28-2018, 07:22 PM | #847 |
Senior Member
Join Date: Feb 2015
Drives: Toyota GT86
Location: Europe
Posts: 919
Thanks: 369
Thanked 554 Times in 301 Posts
Mentioned: 40 Post(s)
Tagged: 2 Thread(s)
|
I have that one, thanks. What I look for is targeted AFR or AFR_Command. It's not super important, but it would be nice to have.
__________________
Last edited by Tor; 02-28-2018 at 08:25 PM. Reason: Deleted a second question - solved with Kodename47's definitions. |
02-28-2018, 10:14 PM | #848 |
Senior Member
Join Date: Sep 2017
Drives: 2022 BRZ Limited Silver
Location: Jacksonville, FL
Posts: 2,532
Thanks: 882
Thanked 2,045 Times in 1,188 Posts
Mentioned: 68 Post(s)
Tagged: 0 Thread(s)
|
Tactrix EcuFlash Info for BRZ 86 FRS Rom flash update and logging
|
The Following User Says Thank You to ermax For This Useful Post: | Tor (02-28-2018) |
02-28-2018, 10:22 PM | #849 |
Senior Member
Join Date: Feb 2015
Drives: Toyota GT86
Location: Europe
Posts: 919
Thanks: 369
Thanked 554 Times in 301 Posts
Mentioned: 40 Post(s)
Tagged: 2 Thread(s)
|
Thanks a lot!
__________________
|
03-10-2018, 07:19 PM | #850 |
Banned
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
|
Added ZA1JN10C USA 2018 Manual rom to first post
|
The Following User Says Thank You to steve99 For This Useful Post: | solidONE (03-11-2018) |
03-10-2018, 07:24 PM | #851 |
Senior Member
Join Date: Feb 2015
Drives: Toyota GT86
Location: Europe
Posts: 919
Thanks: 369
Thanked 554 Times in 301 Posts
Mentioned: 40 Post(s)
Tagged: 2 Thread(s)
|
I'll contribute with a bit better B01C logcfg.txt than the earlier ones linked.
c/f mph/kph bar/psi - default metric.
__________________
|
03-31-2018, 07:57 PM | #852 |
Senior Member
Join Date: Apr 2013
Drives: 2013 FR-S
Location: Seattle
Posts: 806
Thanks: 202
Thanked 320 Times in 199 Posts
Mentioned: 18 Post(s)
Tagged: 1 Thread(s)
|
@steve99 now that OFT is based on A01I, which of these files has the correct addresses?
__________________
2013 Whiteout 6AT FR-S | Perrin Inlet Tube + 2.75" CAI | OpenFlash Header | P&L Catback | 4.88 Final Drive | Dialed in OFT 2.0x Stage 2 E85 | 18x8 Enkei Raijin + 225/40 Michelin Pilot Super Sport | 17x7 Stock + 215/45 Michelin X-Ice Xi-2
|
03-31-2018, 09:46 PM | #853 | |
Banned
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
|
Quote:
Luckly A01I and A01G ecu ram addresses for logging are same, ie jist use A01G ram addresses |
|
04-05-2018, 10:11 PM | #854 |
Banned
Join Date: Dec 2013
Drives: FT86
Location: Australia
Posts: 7,998
Thanks: 1,035
Thanked 4,987 Times in 2,981 Posts
Mentioned: 598 Post(s)
Tagged: 2 Thread(s)
|
Added ZA1JN00P 2018 australian Manual, this is very likely same as ZA1JN00Q but not confirmed yet
|
|
|
Tags |
ecuflash, tactrix, taxtrix, tuning |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
ECUFlash - Getting close! | xjohnx | Software Tuning | 698 | 03-22-2015 12:10 PM |
EcuTek Flash finished but now it shows only a Partial Flash... | Cross | Software Tuning | 32 | 02-12-2014 10:55 AM |
Tactrix Openport | jamesm | Engine, Exhaust, Bolt-Ons | 1 | 01-28-2014 08:27 PM |
Visconti Tuning - Latest BRZ Flash Info | Visconti | Software Tuning | 6530 | 12-24-2013 10:18 PM |
Overboost Protection With OFT/EcuFlash? | FrX | Software Tuning | 9 | 10-23-2013 07:27 AM |