Edelbrock E-Force Supercharger

[FuzzyFunk]

Originally Posted by tracerit

I'm at 30k miles now. I was under the impression that if I installed it myself, there would be NO warranty on anything. So I was figuring having a shop install it, but if I do that then I'll pay the quoted $800 install fee for only 6k miles left of warranty on the limited power train, and have a 3 year warranty on the superhcarger itself. Doesn't seem worthwhile to pay a shop to do it then.

But if I install it myself, will I still have the 3 year warranty on the supercharger? I can roll the dice and waive the 6,000 remaining miles of the limited power train warranty to save $800 and installing it myself.

Yes i believe the 3year/36K warranty, which ever comes first, for the sc is still in viable. I would contact Edelbrock just to make sure though.

[sam69]

Originally Posted by sam69

Ok just scanned this whole thread looking for the size of the intercooler radiator ie; length x height x width so if
some one can help out that would be so

Bump !
Surely someone can help me out with the measurement maybe I need to offer money ....

[86fun]

Here, this should help mate.


These are hand welded so I would imagine sizes might vary a bit.

[BigFatFlip]

Originally Posted by 86fun

Here, this should help mate.


These are hand welded so I would imagine sizes might vary a bit.

I think somebody owes someone a beer

[86fun]

Originally Posted by BigFatFlip

I think somebody owes someone a beer

I'll take a 1L Hofbräu at the Bavarian in Manly NSW Please!


...oh the memories... at least the ones which I didn't lose drinking there!


If anyone needs measurements, I'm not installing for another week so I have everything readily available to measure.

[sam69]

Thanks for that just comparing size against the Sprintex core .

Long way to send a beer but if you ever come to the land of Oz 86 fun let me know and I'll shout you a couple a beers

[-Phil]

Originally Posted by tracerit

In the quest to pinch more pennies, would I be able to rent an Ecutek hardware kit from say motoeast (or does @CounterSpace Garage offer rental kits too?) for $70 ($350 up front, $270 refunded on return), buy an Ecutek license (which is needed) for $350 and then download the CARB tune for free, this would end up being $5070 total ($4650 kit, $70 Ecutek hardware, $350 Ecutek license, $0 CARB tune).

I'd save $330 instead of getting the CARB kit for $5400. Unless I need to get the CARB kit to get the CARB sticker, which now sounds obvious...

Shoot us a PM We'll help you out.

[tracerit]

Is the carb exempt eo certification a sticker or is it stamped on the kit somewhere?

[switchlanez]

Originally Posted by tracerit

Is the carb exempt eo certification a sticker or is it stamped on the kit somewhere?

It's a sticker and supposedly not available yet. Not sure when Edelbrock will start delivering them.

[Edelbrock LLC]

Originally Posted by switchlanez

It's a sticker and supposedly not available yet. Not sure when Edelbrock will start delivering them.

For everyone asking about the E.O. Number sticker.

As soon as we obtain the E.O. # which we will make sure to announce, you would simply call in to our sale staff. We will verify your purchase and the official sticker will be shipped out to you.

- Eddie L.
Edelbrock LLC

[Phantobe]

What file format is the carb tune in?

Sent from my SM-G900V using Tapatalk

[BigFatFlip]

Originally Posted by Phantobe

What file format is the carb tune in?

Sent from my SM-G900V using Tapatalk

It's a .bin file (ecutek)

[avishenoy1]

Originally Posted by 86fun

I'll take a 1L Hofbräu at the Bavarian in Manly NSW Please!


...oh the memories... at least the ones which I didn't lose drinking there!


If anyone needs measurements, I'm not installing for another week so I have everything readily available to measure.

Could you please post measurements of the SC heat exchanger core? I'm curious as to how it compares in size/SA to the Harrop/Cosworth twin core designs.

[BigFatFlip]

Originally Posted by avishenoy1

Could you please post measurements of the SC heat exchanger core? I'm curious as to how it compares in size/SA to the Harrop/Cosworth twin core designs.

I can't speak for @86fun but that one might be a little bit more difficult to do since it involves disassembly of the SC manifold, which may or may not be considered "tampering" and may void the warranty. I believe there have been pics posted earlier that you might be able to questimate the size. How about calling Edelbrock tech service? They might be able to look it up for you.