|
Engine, Exhaust, Transmission Discuss the FR-S | 86 | BRZ engine, exhaust and drivetrain. |
|
Thread Tools | Search this Thread |
07-22-2018, 04:03 PM | #15 |
Senior Member
Join Date: Nov 2016
Drives: 2017 BRZ
Location: USA
Posts: 655
Thanks: 326
Thanked 258 Times in 177 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
I'm not sure, but it has worked for some people who've replaced the driveshaft, and is relatively easy to try and doesn't involve buying parts. It might be that the pinion yoke is balanced separately, so when the driveshaft is bolted up, there is potential for the balancing effects on each to interfere. Again I'm not positive tho.
|
The Following User Says Thank You to gtengr For This Useful Post: | jcw99 (07-23-2018) |
07-22-2018, 04:22 PM | #16 | |
義理チョコ
Join Date: Sep 2014
Drives: a 13 e8h frs
Location: vantucky, wa
Posts: 31,889
Thanks: 52,177
Thanked 36,539 Times in 18,937 Posts
Mentioned: 1108 Post(s)
Tagged: 9 Thread(s)
|
Quote:
__________________
|
|
07-22-2018, 05:20 PM | #17 |
Senior Member
Join Date: May 2013
Drives: 2013 FR-S, white, MT
Location: Puyallup, WA
Posts: 29,892
Thanks: 28,825
Thanked 31,876 Times in 16,444 Posts
Mentioned: 709 Post(s)
Tagged: 2 Thread(s)
|
It would seem to me that the first step would be to measure the pinion angles.
If they were "off", then, since the transmission is aftermarket, to move the transmission up or down or rotate the differential. I'd still have the driveshaft checked for balance. Easy for me to say, as I ease in the air conditioned bedroom to take a looong Sunday afternoon nap humfrz |
The Following User Says Thank You to humfrz For This Useful Post: | Ultramaroon (07-22-2018) |
07-22-2018, 05:37 PM | #18 | |
義理チョコ
Join Date: Sep 2014
Drives: a 13 e8h frs
Location: vantucky, wa
Posts: 31,889
Thanks: 52,177
Thanked 36,539 Times in 18,937 Posts
Mentioned: 1108 Post(s)
Tagged: 9 Thread(s)
|
Quote:
__________________
|
|
The Following User Says Thank You to Ultramaroon For This Useful Post: | humfrz (07-22-2018) |
07-27-2018, 01:51 AM | #19 |
Senior Member
Join Date: Sep 2013
Drives: frs
Location: The depths
Posts: 749
Thanks: 355
Thanked 427 Times in 241 Posts
Mentioned: 5 Post(s)
Tagged: 2 Thread(s)
|
No shop local, and I have tried that. Gonna pull the driveshaft and use the shaft end to check angle.
__________________
|
07-27-2018, 01:52 AM | #20 |
Senior Member
Join Date: Sep 2013
Drives: frs
Location: The depths
Posts: 749
Thanks: 355
Thanked 427 Times in 241 Posts
Mentioned: 5 Post(s)
Tagged: 2 Thread(s)
|
Yes, I’ve tried all four possibilities
__________________
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
WTB: 3.7 or 3.9:1 ring and pinion | Salemate | Canada Classifieds | 0 | 01-25-2018 09:52 AM |
WTB ring and pinion | Salemate | Canada Classifieds | 0 | 03-13-2016 02:07 PM |
Considering going to 3.727 gear/pinion in 6MT | HotLavaMann | Engine, Exhaust, Transmission | 83 | 01-10-2015 10:34 AM |
Change FD ratio to 4.56 by changing only pinion | peachch | Engine, Exhaust, Transmission | 1 | 08-31-2013 01:25 PM |
MFactory Ring and Pinion Sets | JMPoole | Engine, Exhaust, Bolt-Ons | 14 | 07-31-2013 12:09 PM |