|
BRZ First-Gen (2012+) -- General Topics All discussions about the first-gen Subaru BRZ coupe |
|
Thread Tools | Search this Thread |
02-06-2016, 09:15 PM | #1 |
Member
Join Date: Nov 2015
Drives: 06' Forester, 15 '3.6 OBW, 16' BRZ
Location: MD
Posts: 35
Thanks: 1
Thanked 11 Times in 5 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Rear License Plate FRAME
Two Questions:
1. The two black foam adhesive strips glued to the trunk lid under where the license plate attaches. I'm thinking the foam is a good (bad) sponge for water, however I understand it's purpose not to scratch the paint. Keep the foam on, or remove it? 2. I bought a Weathertech stainless steel license plate frame that has FOUR holes to attach the plate to the trunk. Trouble is, the trunk only has TWO screw holes (top) to attach the plate. WHAT have you all done to make the two lower holes look like the two upper holes? My Weathertech frame came with four silver plastic caps to cover the screw heads, but since I can't use screws and caps for the two bottom holes, it's going to look a bit goofy for my OCD. See frame here ------->http://www.weathertech.com/stainlessframe/ Thanks!! |
02-06-2016, 09:22 PM | #2 |
Senior Member
Join Date: Mar 2015
Drives: 2015 Subaru BRZ Limited CWP
Location: SoCal
Posts: 1,561
Thanks: 34
Thanked 669 Times in 469 Posts
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
|
superglue the plastic caps to the frame?
__________________
|
02-06-2016, 09:28 PM | #3 |
Senior Member
Join Date: Sep 2014
Drives: BRZ
Location: Los Angeles
Posts: 3,053
Thanks: 1,773
Thanked 2,451 Times in 1,271 Posts
Mentioned: 79 Post(s)
Tagged: 0 Thread(s)
|
The foam isn't absorbent like a sponge.
Foam also stops rattles. I still got scratches with the foam, so I used the dealer advertisement plate under the licence plate. Lower holes just glue the caps on OR cut the heads of the screws off, glue them on, and then put the caps over them. |
02-06-2016, 11:57 PM | #4 |
Senior Member
Join Date: Jan 2014
Drives: Toyota Highlander; Subaru BRZ (SWP)
Location: California
Posts: 431
Thanks: 137
Thanked 156 Times in 95 Posts
Mentioned: 1 Post(s)
Tagged: 2 Thread(s)
|
I do frameless. I added some foam between the frame and the paint. I also am using a black backplate that goes between the foam and the license plate.
__________________
"Wubalubadubdub! You're a wizard, Harry!"
-Captain Picard(4th incarnation of Dr. Who), Star Wars: Return of the Jar Jar |
02-07-2016, 12:03 AM | #5 |
Country Boy 4 Life
Join Date: Jul 2012
Drives: 19' & 06' Ridgelines, 13' FR-S
Location: EUGENE
Posts: 5,228
Thanks: 6,719
Thanked 5,291 Times in 2,720 Posts
Mentioned: 47 Post(s)
Tagged: 1 Thread(s)
|
I scrapped the foam off. Then put real 3M foam on. It's thicker. I had rusty screws, so I swapped them out for stainless.
|
02-07-2016, 01:13 AM | #6 | |
Senior Member
Join Date: Dec 2011
Drives: Flying in a Blue Dream
Location: California
Posts: 224
Thanks: 205
Thanked 123 Times in 75 Posts
Mentioned: 3 Post(s)
Tagged: 1 Thread(s)
|
Quote:
I put foam weather stripping on the back of the plate on all my vehicles. Doesn't hold water, stops rattles and prevents scratches. |
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
FR-S rear license plate frame suggestions? | tzhu07 | Scion FR-S / Toyota 86 GT86 General Forum | 58 | 03-12-2014 02:36 PM |
New license plate frame | Optimus Prime | FR-S & 86 Photos, Videos, Wallpapers, Gallery Forum | 3 | 07-19-2013 04:58 PM |
FS: First 86 License plate frame... | NorCal_Guy | Miscellaneous | 9 | 07-11-2013 05:50 PM |
Rear License Plate Frame | ashtray | Cosmetic Modification (Interior/Exterior/Lighting) | 19 | 07-23-2012 01:47 AM |
rear license plate frame | meekhotglass | Cosmetic Modification (Interior/Exterior/Lighting) | 1 | 06-20-2012 10:08 PM |