06-27-2015, 04:56 PM | #141 |
Senior Member
Join Date: Apr 2015
Drives: 2015 BRZ
Location: SL,UT
Posts: 111
Thanks: 11
Thanked 58 Times in 30 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
So...those sensors for the downpipe. How did yours go? Due to the bung locations only one of mine barely reaches (I could probably play it like a guitar string) and the other is about two inches too short. So I'm going to have to lengthen mine.
Anyone else ran into that? |
06-27-2015, 04:59 PM | #142 | |
Senior Member
Join Date: Dec 2013
Drives: 2013 Hot Lava
Location: New Bedford
Posts: 215
Thanks: 42
Thanked 44 Times in 34 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Sent from my SAMSUNG-SM-N900A using Tapatalk |
|
06-27-2015, 05:12 PM | #143 |
Senior Member
Join Date: Apr 2015
Drives: 2015 BRZ
Location: SL,UT
Posts: 111
Thanks: 11
Thanked 58 Times in 30 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
I'm not using the clips. I tried swapping them since one is longer than the other. But even then I was an inch or so away from the plug.
|
06-27-2015, 05:20 PM | #144 |
Senior Member
Join Date: Dec 2013
Drives: 2013 Hot Lava
Location: New Bedford
Posts: 215
Thanks: 42
Thanked 44 Times in 34 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
|
06-27-2015, 05:23 PM | #145 | |
Senior Member
Join Date: Jul 2012
Drives: 2013 SWP BRZ
Location: New York
Posts: 2,240
Thanks: 458
Thanked 878 Times in 556 Posts
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
|
Quote:
My front O2 sensor was too short but bending the plug bracket down allowed enough space to connect it. |
|
06-27-2015, 05:24 PM | #146 |
Senior Member
Join Date: Jul 2012
Drives: 2013 FRS Whiteout
Location: MIA
Posts: 1,545
Thanks: 557
Thanked 469 Times in 340 Posts
Mentioned: 33 Post(s)
Tagged: 5 Thread(s)
|
Update, still leaking. Tried a new flange, several gaskets and oil pan sealant. It leaks and only where the turbo and flange meet. I'm removing the turbo and taking a good look at it as something can't be right, this isn't normal and this leak can't be so persistent.
__________________
GTX2867R, moto-tuned , tomei op , motiv fp , Invidia Q300 ti , Rota titan 17x9 +42 , nt555 255/40 , ST coilovers w/cascam , Hotchkis sways
|
06-27-2015, 05:24 PM | #147 |
Senior Member
Join Date: Apr 2015
Drives: 2015 BRZ
Location: SL,UT
Posts: 111
Thanks: 11
Thanked 58 Times in 30 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
Nope. The car has 1500 miles total. Everything is stock. I took a pic but it's really just me pulling on a wire showing about an inch between the plug and the connector. It's the gray one that won't reach. It's going the shortest path too.
|
06-27-2015, 05:25 PM | #148 | |
Senior Member
Join Date: Apr 2015
Drives: 2015 BRZ
Location: SL,UT
Posts: 111
Thanks: 11
Thanked 58 Times in 30 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Hopefully that be fancy one will fix it. |
|
06-27-2015, 06:05 PM | #149 |
Senior Member
Join Date: Dec 2013
Drives: 2013 Hot Lava
Location: New Bedford
Posts: 215
Thanks: 42
Thanked 44 Times in 34 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
Hey yomny how did u mount the intercooler to the crash bar?
Sent from my SAMSUNG-SM-N900A using Tapatalk |
06-27-2015, 06:13 PM | #150 | |
Senior Member
Join Date: Jul 2012
Drives: 2013 FRS Whiteout
Location: MIA
Posts: 1,545
Thanks: 557
Thanked 469 Times in 340 Posts
Mentioned: 33 Post(s)
Tagged: 5 Thread(s)
|
Quote:
This is with sealant, freshly installed, let it cure for 24hrs.. Here is its 24hrs later after a drive and letting it cool down.. leaking! its not horrible but you could see the oil between the sealant. Here's third paper gasket, oem, already saturated with oil, the day after leaked. Here's the O-ring flange, no paper gasket.. leaking. Here's the new flange, the opening for the drain is almost twice as big as the turbo's opening, meaning anything and everything coming out of that turbo oil drain hole should fall well within, well it doesn't lol.
__________________
GTX2867R, moto-tuned , tomei op , motiv fp , Invidia Q300 ti , Rota titan 17x9 +42 , nt555 255/40 , ST coilovers w/cascam , Hotchkis sways
|
|
06-27-2015, 06:43 PM | #151 |
Senior Member
Join Date: Apr 2015
Drives: 2015 BRZ
Location: SL,UT
Posts: 111
Thanks: 11
Thanked 58 Times in 30 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
|
06-27-2015, 07:03 PM | #152 | |
Senior Member
Join Date: Jul 2012
Drives: 2013 FRS Whiteout
Location: MIA
Posts: 1,545
Thanks: 557
Thanked 469 Times in 340 Posts
Mentioned: 33 Post(s)
Tagged: 5 Thread(s)
|
Quote:
@drambo136 Check out this thread, first post you'll see a few good pics of the cutting areas and how to mount. Notice the crash beam on the passenger side has a square hole right in front of the intercooler coupler, I had to cut this open to reach the nut for the bolt secure the intercooler mounting tab, the driver side already has access. http://www.ft86club.com/forums/showthread.php?t=81623
__________________
GTX2867R, moto-tuned , tomei op , motiv fp , Invidia Q300 ti , Rota titan 17x9 +42 , nt555 255/40 , ST coilovers w/cascam , Hotchkis sways
|
|
06-27-2015, 08:56 PM | #154 |
Join Date: Nov 2012
Drives: JDL Turbo FRS, 335SC BRZ (ret)
Location: Lehigh Valley, PA
Posts: 932
Thanks: 368
Thanked 1,547 Times in 525 Posts
Mentioned: 380 Post(s)
Tagged: 6 Thread(s)
|
Those little drips are a pita @yomny. Hate to say it but really common with aftermarket turbo installs. Best thing I can say is don't use paper gaskets and clean the heck out of everything with brake cleaner before putting on any sealant. Then careful with the torque. Overdoing it will have the same effect. It is a low pressure system on the drain side (and coolant side really...) so you don't need torque so much, but a broad clean surface for the gasket maker to stick to and not lift off.
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
HKS Supercharger owners thread | wbradley | Forced Induction | 1048 | 10-12-2023 08:03 PM |
P&L Turbo kit Owners thread | Hawaiian | Forced Induction | 73 | 07-07-2018 02:31 AM |
To Greddy Turbo Owners (or SBD/Zage Turbo).... Melted Radiator Fans? General Opinion? | xuimod | Forced Induction | 106 | 09-01-2016 07:33 PM |
**Offical 213/323/626/818 owners thread** | mr. slim | Southern California | 71 | 10-07-2013 12:58 PM |
P&L Turbo Owners Topic Thread | GTB/ZR-1 | Forced Induction | 4 | 09-01-2013 06:27 PM |