|
Suspension | Chassis | Brakes -- Sponsored by 949 Racing Relating to suspension, chassis, and brakes. Sponsored by 949 Racing. |
|
Thread Tools | Search this Thread |
03-14-2021, 11:24 PM | #1 |
Senior Member
Join Date: May 2020
Drives: BRZ ts
Location: SACRAMENTO
Posts: 752
Thanks: 411
Thanked 788 Times in 301 Posts
Mentioned: 8 Post(s)
Tagged: 1 Thread(s)
|
Stuck Wilwood Pistons
When I went to rebuild my calipers and blow the pistons out of the calipers a couple wouldn’t come out. Most come out but a few don’t budge.
I have a couple thoughts. 1) hit them with a heat gun to help liberate them and then hit them with air. 2) a solvent to break down crud and old seals. 3) insert a rubber stopper I can compress with a nut and bolt and then apply some torque to liberate them. 4) breakdown the calipers via side bolts and some combination of #1&3 |
03-14-2021, 11:38 PM | #2 |
Senior Member
Join Date: Feb 2014
Drives: 2023 BRZ
Location: Denver, CO
Posts: 1,810
Thanks: 1,485
Thanked 1,252 Times in 677 Posts
Mentioned: 34 Post(s)
Tagged: 2 Thread(s)
|
Put the other pistons back in just a little bit and use a clamp to keep them there. Then use compressed air.
__________________
Director of Rocky Mountain 86CUP
|
03-15-2021, 10:13 AM | #3 |
Senior Member
Join Date: Oct 2013
Drives: BRZ, Noble M400, AC-LS7,1956 AC
Location: Wi/Fl
Posts: 1,022
Thanks: 328
Thanked 867 Times in 471 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
If these are track calipers then there is no dust shield and should be serviced regularly.
The dust shield keeps water and dirt out of the pistons. Pat is right on, use a clamp on the good ones, holding the good ones in place and use air and WD 40. You should be able to move the pistons back in and out a little several times to get the lub in there. The build up of dirt or corrosion should come loose. Unless that piston has not been working at all. Last edited by ls1ac; 03-15-2021 at 10:23 AM. |
03-15-2021, 11:31 AM | #4 |
Senior Member
Join Date: Feb 2014
Drives: 2023 BRZ
Location: Denver, CO
Posts: 1,810
Thanks: 1,485
Thanked 1,252 Times in 677 Posts
Mentioned: 34 Post(s)
Tagged: 2 Thread(s)
|
Then hit the outside of the pistons really well with a green Scotch Brite pad.
__________________
Director of Rocky Mountain 86CUP
|
The Following User Says Thank You to Pat For This Useful Post: | dpfarr (03-15-2021) |
03-15-2021, 11:51 AM | #5 |
Senior Member
Join Date: Jan 2018
Drives: Crapcan
Location: Oregon
Posts: 11,191
Thanks: 18,232
Thanked 16,358 Times in 7,398 Posts
Mentioned: 108 Post(s)
Tagged: 0 Thread(s)
|
Calipers with square o-rings by chance? If so you will want to split the bodys and use a combination of compressed air and some kind of inside puller like your rubber stopper idea. Rock the piston while you put air pressure to it. What I tend to see with Wilwood calipers with square orings is if the caliper body gets deflection it shears the corner of the oring and it gets bound between the piston and the body causing the issue you are having. Don’t think heat is going to help.
Sent from my iPhone using Tapatalk
__________________
"Experience is the hardest kind of teacher. It gives you the test first and the lesson afterward." -Oscar Wilde.
|
The Following User Says Thank You to NoHaveMSG For This Useful Post: | dpfarr (03-15-2021) |
03-15-2021, 09:15 PM | #6 |
Senior Member
Join Date: May 2020
Drives: BRZ ts
Location: SACRAMENTO
Posts: 752
Thanks: 411
Thanked 788 Times in 301 Posts
Mentioned: 8 Post(s)
Tagged: 1 Thread(s)
|
Yea, square rings.
In regards to the clamp, I feel like using a thicker wood block between the pistons that move and a thinner one where they’re not is equivalent? Is using wd40 inside calipers body not a big deal? I’m probably going to get them powder coated again anyways so I guess hitting them with brake cleaner after using wd40 would be doable. |
03-15-2021, 09:45 PM | #7 |
Senior Member
Join Date: Feb 2014
Drives: 2023 BRZ
Location: Denver, CO
Posts: 1,810
Thanks: 1,485
Thanked 1,252 Times in 677 Posts
Mentioned: 34 Post(s)
Tagged: 2 Thread(s)
|
A wood block should work just fine as long as it is precisely the right thickness.
__________________
Director of Rocky Mountain 86CUP
|
03-15-2021, 09:46 PM | #8 | |
Senior Member
Join Date: Jan 2018
Drives: Crapcan
Location: Oregon
Posts: 11,191
Thanks: 18,232
Thanked 16,358 Times in 7,398 Posts
Mentioned: 108 Post(s)
Tagged: 0 Thread(s)
|
Quote:
You are replacing the orings anyway, WD isn’t going to hurt anything else. Check the piston bores for burs before you put new ones in. Using the thick/thin wood block like that should work. Watch your fingers, those things are going to come out at Mach 10. Sent from my iPhone using Tapatalk
__________________
"Experience is the hardest kind of teacher. It gives you the test first and the lesson afterward." -Oscar Wilde.
|
|
03-16-2021, 02:56 PM | #9 |
Senior Member
Join Date: Oct 2013
Drives: BRZ, Noble M400, AC-LS7,1956 AC
Location: Wi/Fl
Posts: 1,022
Thanks: 328
Thanked 867 Times in 471 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
The problem with a wood block is that the opposing piston will come out. If it is a 4 piston then you can use the block for two but the one opposing the stuck one will pop out.
|
The Following User Says Thank You to ls1ac For This Useful Post: | dpfarr (03-17-2021) |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
RR racing BBK - 4 pistons | Lorico | Suspension | Chassis | Brakes -- Sponsored by 949 Racing | 9 | 01-31-2017 02:55 AM |
Wilwood 2 Piece aluminum hat front BBK 6 Pistons | Kazuya | Canada Classifieds | 13 | 01-22-2016 10:39 PM |
13.5:1 Pistons | woode | Forced Induction | 13 | 04-27-2014 11:06 PM |
CP Pistons for FA20 | MattR | Engine, Exhaust, Transmission | 1 | 10-04-2012 07:22 PM |