Drakiv's FBM Stage 2 Turbo project Shadow Build
Welcome to my Shadow build.....
http://www.ft86club.com/forums/pictu...ictureid=11053 http://www.ft86club.com/forums/pictu...ictureid=11002 http://www.ft86club.com/forums/pictu...ictureid=11050 http://www.ft86club.com/forums/pictu...ictureid=11051 http://www.ft86club.com/forums/pictu...ictureid=10425 http://www.ft86club.com/forums/pictu...ictureid=11077 Here are the current mods on the car as it sits: Huge thanks to LJ and his team @FullBlownMotorsports and Matt and his team over @JacksTransmissions Both companies were very helpful and extremely professional and I cannot say enough good things about both of them. Engine: 9.5:1 Arias Pistons FBM Connecting Rods FBM Stage 2 Block FBM Stage 2 heads FBM Stage 2 Turbo kit with GTX3582r Tial 44mm Wastegate Tial 50mm Q BOV FBM 4 bar map sensor FBM 19 row oil cooler kit FBM Radiator with shroud and slim fans FBM Silicone Radiator hoses FBM Dual Oil catch can FBM Oil Pan FBM Walbro 485 fuel pump kit FBM Fuel Rails ID 1700cc injectors FBM Surge tank with triple Walbro 485 pumps FBM Fuel return system with FBM 1:1 FPR Cusco Motor Mounts RaceSeng cam plate ReXpeed Carbon Fiber strut Mounts JDL 3" Overpipe-Frontpipe combo Perrin 3" Resonated cat back ECUTeK tuned by FBM on E85/91 Drivetrain: Clutch Masters twin plate clutch MTEC shift springs MTEC stainless steel clutch hose KARTboy Short Shifter with bushing PAR Engineering straight cut synchromesh 1st-6th gear set Velox Motorsports Billet Clutch Fork and Pivot Megan Racing Reinforced Transmission Mount Velox Motorsports Carbon Fiber driveshaft 3.73 Final drive upgrade w/ supra bearing and solid spacer Harrop Diff Cover Neo Synthetic 75W-90 RHD gear oil (Diff and Trans) Driveshaft shop 1000HP Pro-level axle & hub kit Exterior: Seibon TS Carbon Fiber hood Aerocatch hood pins Valenti Black edition sequential taillights Wheel/Tires: Forgestar F14 Wheels - 18x8.5 +35 Front and 18x9.5 +40 Rear Hankook Ventus V12 evo2 - 245/35/18 Front and 265/35/18 Rear Suspension: Feal 441 Coilovers Velox Rear LCA SPL PRO Rear End Links Adjustable Toe Arms by Velox SPL Bumpsteer Adjustable Front Tie Rod Ends SPL Trailing Arms Hotchkis Front End Links ST Suspensions Sway Bar Kit Front and Rear Interior: NRG 315mm Carbon Fiber Steering Wheel Red Stitching NRG Hub Adapter with resistors NRG Quick Release Ver. 3 Raceseng Ashiko Shift knob |
So here is my list of what I have planned and I will update this page later as I start to get things completed. It will be a somewhat slow start this first couple months because I am also planning my wedding, but once that is finished in March I will have some fairly hefty upgrades on the way. So please bare with me as I start my journey into this project. None of this is in order of what gets done first, it is just a rough list.
1. Seibon Carbon Fiber TS hood *Installed 2. Forgestar F14 wheels 18x8.5 +35 - 18x9.5 +40 *Installed 3. Feal 441 Coilovers *Installed 4. SPL PRO Rear End Links *Installed 5. FT-86 SpeedFactory Adjustable Toe Arms by Velox *Installed 6. SPL Bumpsteer Adjustable Front Tie Rod Ends *Installed 7. SPL Trailing Arms *Installed 8. Hotchkis Front End Links *Installed 9. ST Suspensions Sway Bar Kit Front and Rear *Installed 10. FT-86 SpeedFactory / Velox Rear LCA *Installed 11. MTEC shift springs *Installed 12. Megan Racing Transmission Mount *Installed 13. Velox Motorsports Billet Clutch Fork and Pivot *Installed 14. MTEC Stainless Steel Clutch Line *Installed 15. PAR Engineering straight cut synchromesh gear set *Installed 16. Velox Motorsports Carbon Fiber driveshaft *Installed 17. 3.73 Final drive upgrade w/ supra bearing and solid spacer *Installed 18. NRG 315mm Carbon Fiber Steering Wheel Red Stitching *Installed 19. NRG Hub Adapter with resistors *Installed 20. NRG Quick Release Ver. 3 *Installed 21. GCS Smoked 4th F1 Style Brake Light V2 *Installed 22. FBM stage 2 short block *Installed 23. FBM stage 2 heads *Installed 24. FBM head studs *Installed 25. FBM head gasket *Installed 26. FBM Stage 2 turbo kit *Installed 27. Clutchmasters Twin Disc *Installed 28. Driveshaft shop Pro-level axle & hub kit *Installed 29. Raceseng Cam plate *Installed 30. Cusco Reinforced Engine Mounts *Installed Still to come: Engine: Motec ECU Dry Sump kit Exterior: Wide Body Fenders Street Faction Engineering Chassis Mount Wing Charvonia Design V1 Rear Diffuser 6 Piston Front BBK and 4 Piston Rear BBK Dry Carbon Fiber Hood Dry Carbon Fiber Doors Dry Carbon Fiber Roof replacement Dry Carbon Fiber Trunk Wheels: HRE C105 or C100 18 x 12 -40 squared with 10mm spacers in rear Hoosier A7 315/30/18 squared Interior: Interior removal Full Roll Cage Racing seat with harness http://www.ft86club.com/forums/pictu...ictureid=10113 http://www.ft86club.com/forums/pictu...ictureid=10237 http://www.ft86club.com/forums/pictu...ictureid=10425 I have some of it ordered already, and my goal is to get this car finished by May of 2017. I will post pictures as I get equipment in and/or installed. Cheers! |
I purchased a 2015 BRZ Limited in Crystal Black Silica. So far the car has been a lot of fun, and I have done a few mods to it since I picked it up. Nothing major, just headers, an overpipe, and a catback with the support of an OFT stage 2 UEL tune on 91 octane (boooo California). But even with all of this, the power to me is lacking. And man, do I miss having a turbo. So I have been really racking my brain for a while now on what I wanted to do, buy a different car? Or upgrade the hell our of the BRZ. I really like the BRZ, the platform is amazing and really reminds me of my '93 RX7 sometimes....minus the power. So I finally decided that I want to go into the turbo realm with the BRZ. I will post some picture of how the car sits now, and will try to post updates as much as possible in the coming months. I am currently in talks with FullBlown Motorsports, and am looking into a stage 2 motor, stage 2 heads, and their stage 2 turbo kit. My goal is around 600 WHP, and before you ask why or what I plan to do with that type of power.....well, because I can first and foremost. I have plans for after the car is done, but that will be released much later.
http://www.ft86club.com/forums/pictu...pictureid=9033 http://www.ft86club.com/forums/pictu...pictureid=9750 http://www.ft86club.com/forums/pictu...pictureid=9297 |
I do say, good sir, this exquisite car will be quite pricey. I bid you adieu.
|
Got my Intec hi mount brake light and Valenti taillights installed that I got for Christmas. I just recently got around to installing them.
http://www.ft86club.com/forums/pictu...pictureid=9995 |
I've been in the same exact boat as you lately.. Been considering selling the FRS for a new EVO but the more and more I think about it the more I love my FRS. So in the future I plan to go down the same route as you, turbo with built engine. I really miss having the power of my old 94 twin turbo Z. But this car definately has the better feel to it and might be as tail happy as my old Z. Nonetheless I hope you have fun building your BRZ!
|
Ordered up my Forgestar F14 rims, got my Velox LCA's. Looking to get a set of Feal coilovers, and am in talks with PAR to get a new straight cut gear set. Will post pictures as everything starts to come in, for now here are the LCA's.
http://www.ft86club.com/forums/pictu...ictureid=10042 |
Installed red RallyArmor mud flaps yesterday, they came out pretty good. I also got my Seibon Carbon Fiber TS hood the other day, I am just waiting on my Aerocatch hood pins to come in so I can install it.
http://www.ft86club.com/forums/pictu...ictureid=10105 |
I see you changed the title.
|
Quote:
I did, what do you think? |
Wouldn't black snow be disgusting :)
|
Quote:
|
Quote:
Quote:
gozen reiji 午前零時 - midnight or Mayonaka 真夜中 - midnight,deep night |
Quote:
川側の雪の中で黒鬼 - black demon in the snow by the river side |
All times are GMT -4. The time now is 10:46 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by
Advanced User Tagging v3.3.0 (Lite) -
vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.