If you could see Extreme Dimensions make a new part for frs/brz what would it be?
 

Just like the post says if you could see Extreme Dimensions make a new part what would it be?

Alot of the parts we make like the Gt Concept Kit and 86-R are exclusive to Extreme Dimensions!

Please post up what you would like to see us make and we can see if we can get it done!

Oem Carbon Creations Fenders, Different Wing Options, Hoods, Trunks, New Lip Kits, SideSplitters etc

post it up and if you have pictures of what you want as well or something similar post them!

A OEM style (and fitting) rear bumper with Quad tip exhaust openings.

Does anybody make it and you have any pictures?

There has been fabricated ones from the OEM bumper. But no real aftermarket direct OEM replacements.

@Extreme Dimensions if you are serious in this, please make the FRS release seris front lip
http://o.aolcdn.com/hss/storage/mida...ries-10-ny.jpg

We are always looking for new parts to build and thats pretty nice! any pictures of the rear?

I would love to see something that could replace the FRS OEM center console dash. If you didn't get a monogram or brz with dual climate control/push to start your stuck with a really tacky/cheap and lame as hell interior.

Just a thought as I have seen nothing on the market to mod that area.

BRZ Limited is so nice :O
http://media.caranddriver.com/images...s-1280x782.jpg

We don't do any interior parts just exterior but thanks for the input!

http://www.ft86club.com/forums/showthread.php?p=1459413

Here is a thread where a member fabricated one out of the OEM bumper.

+1

:eyebulge: quad tips

FT86SpeedFactory and a few other places sell push fit anodized aluminum rings for the base climate control.

Stylish (read: complimenting) front and rear wide fenders. Enough to allow more meat in the rear at the very least for us guys wanting to go straight.

Something original. Your only original (I think) piece is that sharp front lip.

Can we FINALLY get better shots of the "Sti concept" styled BRZ body kit and the one for the FR-S that aren't blurry pottato cam or photo shopped pictures then.

I'd push for fenders similar to DF-Aero/Todoroki that are not wider, for those of us not wanting a wider front fender than the rear quarters.

Also a few members have chimed in about smooth fenders without the cutout/garnish trim, and instead a clean bodyline for a sleeker look.

I'd recommend exploring options with the front grille, and maybe rear or side window louvers. The grille is hands down one of the most neglected parts of the car. And if you could offer an affordable alternative to TRD's high priced rear window louvers, you'd make a lot of people happy.

My .02

http://www.moto-verso.co.uk/wp-conte..._concept_6.jpg

TRD Griffon front bumper and front fender(might not be a wide body fender, or a wider fender that can fit oem bumper. So that one can order either front bumper or fender in stead of both together as a package).

Carbon fiber roof skin overlay.

http://www.hks-power.co.jp/en/produc...rts/index.html

That is the exhaust I ordered. The garnishes still maintain a very OEM look IMO. I looked into the TRD garnishes but to me they protrude too much.

I agree with @tahdizzle as this exhaust kit MSRP's for around $2200 and has to be shipped from Japan (for now anyway) It would be nice to have a bumper garnish that can accommodate a quad exhaust and doesn't stick 6 inches out the rear of the vehicle. That would really open up quad exhaust options from custom shops and other manufacturers

Would love to see a professionally done version of this...

I think this particular one has been floating around these forums for a while and someone custom fabricated this example from a real GTR wing.

http://s9.postimg.org/hggwpdjyn/AY0_F3344.jpg

Lower front vent replacement that is just a scoop - no fog or signal. Lot's of us have aftermarket lights with the signal in the headlight assembly.

http://www.ft86club.com/forums/showthread.php?t=55945

aggresive ducktail trunk and front hood with scoop

I'd like a paintable black cover to fit fairly closely over the mounting base for the radio antenna. The purpose would be to delete the tall antenna without installing a ridiculous looking shark fin. In other words keep the low profile of the existing antenna base. If a wire could be added inside the cover to maintain some radio functionality that would be a plus.

The street version of the Rocketbunny kit. The rear lip for people who likes the style but doesn't want to cut their bumper. If you make this I'll be your first customer XD

http://jonsibal.com/blog/wp-content/.../TRUST8616.jpg

I second this!

ALL IN FAVOR SAY I!

I third this lol

GT86 Aero Spoiler
 

Please make/get the GT86 Aero spoiler. Its awesome and its functional.

http://blog.guerillaracing.com/wp-co...2/10/86ad2.jpg

As far as I know nobody in the US currently has a knockoff of this and the legit one is $1200 plus.

They already are making them overseas, all you would need to do is buy a few and start stocking them. I'm nearly positive you would be the first in the US.

I'm still waiting to see pictures of your roof spoiler installed. It looks good on your site but there's no clear prictures of it from different angles

A flat low profile antenna (non shark fin)

http://www.ft86club.com/forums/showthread.php?t=12105

How about the rest of the kit too?

Lol wait. What. It's functional? Lol. :lol::lol:

A new cupholder design.

I would like to see an agressive poly rear bumper. I like poly and have never had a fiber or carbon parts fit perfect until I got my parts shipped from seibon or Cwest Japan. Not that I dont like your kits im just weary of US kits unless they are poly. Ill try to find a pic for you. Hell in a fee weeks ill have an LS2 put in so I would volenteer to test fit it and or be sponsored :-)

More aggressive widebody. Do it.
http://brzsuba.ru/wp-content/gallery/news/603.jpg
http://torquepost.files.wordpress.co...gt300-live.jpg

Second for Louvers that don't break the bank! (Photo credit @nataku)

http://i1283.photobucket.com/albums/...ps1b072d0d.jpg

For serious! I read it on the internet so it has to be true...

Any pictures of the concept kit actually fitted to a car? All the pictures I see look like renderings.

A rear diffuser that doesn't stick out as far as the driveway labs one. I know it doesn't stick out too far, but I'd like a less aggressive one that still serves as functional.

Even though this is only ever a minor inconvenience, I'd like to see a cover for the valet button in the trunk. My stuff is always sliding around and hitting it.

Make a real functional rear diffuser where the old one would be cut out. and I guess an exhaust would have to go with that. many have tried few have succeeded here