follow ft86club on our blog, twitter or facebook.
FT86CLUB
Ft86Club
Delicious Tuning
Register Garage Members List Calendar Search Today's Posts Mark Forums Read

Go Back   Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > Search Forums


Showing results 1 to 10 of 10
Search took 0.70 seconds.
Search: Posts Made By: ???
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 09-29-2014, 12:09 AM
Replies: 59
Views: 35,711
Posted By CSG Mike
??? the kit will not mess with bias unless you...

??? the kit will not mess with bias unless you inappropriately select pads and alter it yourself.
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 09-28-2014, 03:21 PM
Replies: 59
Views: 35,711
Posted By Dezoris
No you have to get pads for the CP8350 AP...

No you have to get pads for the CP8350 AP Calipers which is very common. And then same pads for rear oem size.
Forum: Suspension | Chassis | Brakes -- Sponsored by 949 Racing 09-28-2014, 02:36 PM
Replies: 59
Views: 35,711
Posted By Dezoris
The AP kit is probably the most tested on the...

The AP kit is probably the most tested on the Forums from track users. Its pretty consistent in terms of performance and it definately responds best with the same pad compound at all four corners...
Forum: Engine, Exhaust, Bolt-Ons 06-20-2014, 11:40 AM
Replies: 1,902
Views: 403,927
Posted By GrimmSpeed
The air straightener is often seen in many...

The air straightener is often seen in many different forms on LOTS of MAF sensors. A lot of people will mistakenly say that it is to smooth turbulent air before it crosses the MAF sensor, so the...
Forum: Forced Induction 06-20-2014, 07:57 AM
Replies: 124
Views: 94,903
Posted By shiro
:thumbsup: Pretty much summed it up. Though...

:thumbsup: Pretty much summed it up.

Though if you do go with another kit like FBM, you should consider their recirculating BOV. It should give you a smiliar (or same) effect that the Greddy kit...
Forum: Forced Induction 06-20-2014, 07:05 AM
Replies: 124
Views: 94,903
Posted By rocketbunny86
FBM should be equally good and with all the...

FBM should be equally good and with all the supporting mods for their kit even better....short piping is the plus but trimming crash beam is:thumbdown:

With no BOV the turbo flutters tututututu,I...
Forum: Engine, Exhaust, Bolt-Ons 06-19-2014, 09:04 PM
Replies: 1,902
Views: 403,927
Posted By Slysdexia
On the one hand, it is theoretically a...

On the one hand, it is theoretically a restriction in the pipe, but not one you would ever run into on this engine.

Anyway, the straightener is there to make sure that the air passing the MAF is...
Forum: Engine, Exhaust, Bolt-Ons 06-19-2014, 06:36 PM
Replies: 1,902
Views: 403,927
Posted By GrimmSpeed
I remember that day like the back of my hand. We...

I remember that day like the back of my hand. We had done 141 pulls, about 61 total miles at WOT. We were (and still are) using 91 octane, and it was 18 degree F outside, so humidity was not a...
Forum: Engine, Exhaust, Bolt-Ons 06-19-2014, 06:14 PM
Replies: 1,902
Views: 403,927
Posted By GrimmSpeed
Yeah, and neither does ours :( I've read too...

Yeah, and neither does ours :( I've read too much on this forum about people having them same exact problem, and all the time they've put into fixing it and dealer visits, etc.



Hahahahaha,...
Forum: Southeast 02-10-2014, 05:41 PM
Replies: 19
Views: 5,492
Posted By hypermax
$50 for 3 pulls

$50 for 3 pulls
Showing results 1 to 10 of 10

 
Forum Jump

All times are GMT -4. The time now is 11:40 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.

Garage vBulletin Plugins by Drive Thru Online, Inc.